L19 磁性元器件 标准查询与下载

IEC 60424-3:2015 铁氧体磁芯.表面缺陷极限指南.第3部分:ETD芯、EER芯、EC芯和E芯

This part of IEC 60424 gives guidelines on allowable limits of surface irregularities applicable to ETD-cores, EER-cores, EC-cores and E-cores in accordance with the relevant general specification. This standard is a specification useful in the negotiations between ferrite core manufacturers and customers about surface irregularities.

Ferrite cores - Guidelines on the limits of surface irregularities - Part 3: ETD-cores, EER-cores, EC-cores and E-cores

DIN EN 60205 Berichtigung 1:2015 磁性零件有效参数的计算 (IEC 60205-2006 + A1-2009); 德文版本EN 60205-2006 + A1-2009, DIN EN 60205-2009-08勘误表

Calculation of the effective parameters of magnetic piece parts (IEC 60205:2006 + A1:2009); German version EN 60205:2006 + A1:2009, Corrigendum to DIN EN 60205:2009-08

BS EN 60404-5:2015 磁性材料 永磁（硬磁）材料 磁性能的测量方法

Magnetic materials. Permanent magnet (magnetically hard) materials. Methods of measurement of magnetic properties

BS EN 60404-8-1:2015 磁性材料.特定材料规范.硬磁材料

Magnetic materials. Specifications for individual materials. Magnetically hard materials

DB44/T 1568-2015 温敏铁氧体磁芯

本标准规定了温敏铁氧体磁芯的术语和定义、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于额定电压不超过250 V、用于温控开关的温敏铁氧体磁芯（磁件）（以下简称：铁氧体磁芯）。

Temperature Sensitive Ferrite Core

DB44/T 1349-2014 高性能软磁铁氧体材料检测规范

本标准规定了高性能软磁铁氧体材料的术语和定义、型号标识及分类、试样环和测试环境、检测方法、检验规则。 本标准适用于高性能软磁铁氧体材料（以下简称材料）。

Testing specification for high-performance soft ferrite materials

JIS C 2560-1:2014 用铁酸盐制造的磁心.第1部分:通用规格

Cores made of ferrite -- Part 1: Generic specification

ASTM A773/A773M-14 使用磁滞曲线记录仪测定低矫顽磁性材料的直流磁性能的标准试验方法

5.1 Hysteresigraphs permit more rapid and efficient collection of normal induction and dc hysteresis (B-H loop) data as compared to the point by point ballistic Test Methods A341/A341M and A596/A596M. The high measurement point density offered by computer-automated systems is often required for computer aided design of electrical components such as transformers, motors, and relays. 5.2 Hysteresigraphs are particularly desirable for testing of semihard and hard magnetic materials, where either the entire second quadrant (demagnetization curve) or entire hysteresis loop is of primary concern. Test Method A977/A977M describes the special requirements for accurate measurement of hard (permanent magnet) materials. 5.3 Hysteresigraphs are not recommended for measurement of initial permeability of materials with high magnetic permeability such as nickel-iron, amorphous, and nanocrystalline materials due to errors associated with integrator drift; in these cases, Test Method A596/A596M is a more appropriate method. 5.4 Provided the test specimen is representative of the bulk sample or lot, this test method is well suited for design, specification acceptance, service evaluation, and research and development. 1.1 This test method provides dc hysteresigraph procedures (B-H loop methods) for the determination of basic magnetic properties of materials in the form of ring, spirally wound toroidal, link, double-lapped Epstein cores, or other standard shapes that may be cut, stamped, machined, or ground from cast, compacted, sintered, forged, or rolled materials. It includes tests for normal induction and hysteresis loop determination taken under conditions of continuous sweep magnetization. Rate of sweep may be varied, either manually or automatically at different portions of the curves during measurement. 1.2 The equipment and procedures described in this test method are most suited for soft and semi-hard materials with intrinsic coercivity less than about 100 Oersteds [8 kA/M]. Materials with higher intrinsic coercivities should be tested according to Test Method A977/A977M. 1.3 The values and equations stated in customary (cgs-emu and inch-pound) or SI units are to be regarded separately as standard. Within this standard, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Direct Current Magnetic Properties of Low Coercivity Magnetic Materials Using Hysteresigraphs

SJ/T 3172.13-2013 铁氧体磁心的尺寸 第13部分：电源用PQ型磁心

Dimensions of ferrite cores Part 13: PQ cores for power supplies

SJ/T 9072.3-2013 软磁铁氧体磁心术语和定义 第3部分：变压器和电感器磁心制造厂产品目录中有关铁氧体材料资料的导则

Soft ferrite cores terms and definitions - Part 3: Guidelines for information on ferrite materials in manufacturers' catalogs of transformer and inductor cores

SJ/T 3172.16-2013 铁氧体磁心的尺寸 第16部分：UF型磁心

Dimensions of ferrite cores Part 16: UF type cores

SJ/T 2743-2013 电源用磁性氧化物磁心（EC磁心）的尺寸

Dimensions of Magnetic Oxide Cores (EC Cores) for Power Supplies

SJ/T 1766-2013 软磁铁氧体材料分类

Classification of soft ferrite materials

SJ/T 11454-2013 软磁铁氧体环形磁心涂层尺寸及公差

Coating Dimensions and Tolerances of Soft Ferrite Ring Cores

SJ/T 3172.6-2013 铁氧体磁心的尺寸 第6部分：ETD型磁心

Dimensions of Ferrite Cores Part 6: ETD Type Cores

SJ/T 3172.15-2013 铁氧体磁心的尺寸 第15部分：EI型磁心

Dimensions of Ferrite Cores Part 15: Type EI Cores

SJ/T 10383-2013 软磁铁氧体用氧化铁

Iron oxide for soft ferrite

DIN EN 60404-11:2013 磁性材料.第11部分:磁带和磁条表面绝缘电阻测定的试验方法(IEC 60404-11-1991+A1-1998+A2-2012).德文版本EN 60404-11-2013

Magnetic materials.Part 11: Method of test for the determination of surface insulation resistance of magnetic sheet and strip (IEC 60404-11:1991 + A1:1998 + A2:2012); German version EN 60404-11:2013

BS EN 60404-11:2013 磁性材料.测定磁性薄板和带材表面绝缘电阻的试验方法

Magnetic materials. Method of test for the determination of surface insulation resistance of magnetic sheet and strip

DIN EN 62358:2013 铁氧体磁芯. 气隙铁芯的标准电感因数及其公差 (IEC 62358-2012); 德文版本EN 62358-2012

Ferrite cores - Standard inductance factor for gapped cores and its tolerance (IEC 62358:2012); German version EN 62358:2012