Q04 基础标准与通用方法 标准查询与下载

JIS A 1475:2004 建筑物材料吸湿性能的试验方法

この規格は，建築材料の平衡含水率の測定方法について規定する。

Method of test for hygroscopic sorption properties of building materials

BS EN 13872:2004 平整和/或找平复合物的试验方法.尺寸变化的测定

This European Standard specifies the measurement of dimensional change of a hydraulic setting smoothing and/or levelling compound which is referred to in the following as "smoothing and/or levelling compound".

Method of test for smoothing and/or levelling compounds - Determination of dimensional change

ASHRAE NA-04-7-1-2004 使用认证数据的洁净室,以确定退化及改造

Using Certification Data of Cleanrooms to Determine Degradation and Retrofit

Using Certification Data of Cleanrooms to Determine Degradation and Retrofit

BHMA CERTIFIED PRODUCTS DIRECTORY-2004 经过认证的产品目录

Latch bolt operated by lever or knob from either side. Dead bolt operated by key from either side.

Certified Products Directory

ASHRAE NA-04-7-3-2004 在洁净实验室的21个办法以确定能源效率的机会的利用基准

Using Benchmarking to Identify Energy Efficiency Opportunity in Cleanrooms: The Labs 21 Approach

Using Benchmarking to Identify Energy Efficiency Opportunity in Cleanrooms: The Labs 21 Approach

ASTM C1603-04e1 水中固体颗粒测量的标准试验方法

1.1 This test method covers the measurement of the solids content in water for use as mixing water in ready-mixed concrete and the measurement of its density. Solids content is expressed in terms of parts per million (ppm) or in terms of percent by mass of the water sample.1.2 The values stated in SI units are to be regarded as standard; inch-pound units are shown in parenthesis for information only.1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Solids in Water

ASTM D6103-04 受控低强度材料的流动连续性(CLSM)的标准试验方法

This test method is intended to provide the user with a procedure to determine the fluidity of CLSM mixtures for use as backfill or structural fill. This test method is considered applicable to fresh CLSM containing only sand as the aggregate or having coarse aggregate smaller than 19.0 mm (¾ in.). If the coarse aggregate is larger than 19.0 mm (¾in.), the test method is applicable when it is made on the fraction of CLSM passing a 19.0 mm (¾ in.) sieve, with the larger aggregate being removed in accordance with the section on Additional Procedures for Large Maximum size Aggregate Concrete in Practice C 172. Note 18212;Removing the coarse aggregate will alter the characteristics of the mix and therefore will give information only about the remaining material. It is suggested that for mixes containing coarse aggregate 19.0 mm ( ¾ in.) or larger, a measurement of the slump is more appropriate. For non-flowable CLSM, or for mixtures that do not come out of the flow cylinder easily, measure the slump as outlined in Test Method C 143. This test method is one of a series of quality control tests that can be performed on CLSM during construction to monitor compliance with specification requirements. The other tests that can be used during construction control are Test Methods D 4832, D 6023, and D 6024. Note 28212;The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D 3740 does not in itself assure reliable results . Reliable results depend on many factors; Practice D 3740 provides a means of evaluating some of those factors.1.1 This test method covers the procedure for determination of the flow consistency of fresh Controlled Low Strength Material (CLSM). This test method applies to flowable CLSM with a maximum particle size of 19.0 mm (3/4 in.) sieve. 1.2 The values stated in SI units are to be regarded as standard. The inch-pound equivalents are given for information only. 1.3 CLSM is also known as flowable fill, controlled density fill, soil-cement grout, unshrinkable fill, K-Krete, and other similar names. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Flow Consistency of Controlled Low Strength Material (CLSM)

ASTM C1603-04 水中固体颗粒测量的标准试验方法

1.1 This test method covers the measurement of the solids content in water for use as mixing water in ready-mixed concrete and the measurement of its density. Solids content is expressed in terms of parts per million (ppm) or in terms of percent by mass of the water sample.1.2 The values stated in SI units are to be regarded as standard; inch-pound units are shown in parenthesis for information only.1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Solids in Water

ASTM E84-04 建筑材料表面燃烧特性的标准试验方法

1.1 This fire-test-response standard for the comparative surface burning behavior of building materials is applicable to exposed surfaces such as walls and ceilings. The test is conducted with the specimen in the ceiling position with the surface to be evaluated exposed face down to the ignition source. The material, product, or assembly shall be capable of being mounted in the test position during the test. Thus, the specimen shall either be self-supporting by its own structural quality, held in place by added supports along the test surface, or secured from the back side.1.2 The purpose of this test method is to determine the relative burning behavior of the material by observing the flame spread along the specimen. Flame spread and smoke developed index are reported. However, there is not necessarily a relationship between these two measurements.1.3 The use of supporting materials on the underside of the test specimen has the ability to lower the flame spread index from those which might be obtained if the specimen could be tested without such support. These test results do not necessarily relate to indices obtained by testing materials without such support.1.4 Testing of materials that melt, drip, or delaminate to such a degree that the continuity of the flame front is destroyed, results in low flame spread indices that do not relate directly to indices obtained by testing materials that remain in place.1.5 The values stated in inch-pound units are to be regarded as the standard.1.6 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Surface Burning Characteristics of Building Materials

DB42/T 268-2003 蒸压粉煤灰加气混凝土砌块工程技术规程

为了在工业与民用建筑工程中 推广应用蒸压粉煤灰加气混凝土砌块（以下简称砌块），防止墙体裂缝，做到技术先进、经济合理及保证施工质量，特制订本规程。本规程适用于建筑工程非承重墙砌块砌体的材料、设计构造、施工质量的控制和验收。应用本规程的同时，还应符合国家现行其他有关标准、规范的规定。

Technical specification for autoclaved fly ash aerated concrete blocks engineering

BS EN ISO 15148:2003 建筑材料和产品的湿温性能.部分浸入法测定吸水系数

Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion

JIS A 2201:2003 用风扇加压法测试建筑物气密性能的试验方法

この規格は，送風機を用いて建物内外に圧力差を生じさせ，主に住宅に供する建物及び建物の部位における気密性能を試験する方法について適用する。備考1.この規格でいう住宅とは，戸建て住宅，共同住宅，長屋などの1住戸を対象とする。一般 建築についても，この規格に準じて適用できる。 2.建物内外に圧力差を生じさせる方法には，室内を加圧する場合ど減圧する場合があり，それぞれを加圧法及び減圧法と称している。

Test method for performance of building airtightness by fan pressurization

ASTM E2110-03 外部绝缘和装饰系统(EIFS)的标准术语

1.1 This terminology consists of terms and definitions pertaining to materials and processes used in the design and application of exterior insulation and finish systems (EIFS).

Standard Terminology for Exterior Insulation and Finish Systems (EIFS)

ASTM C670-03 制定建筑材料试验方法用精密度和偏差说明的标准实施规程

1.1 This practice supplements Practice E 177, in order to provide guidance in preparing precision and bias statements for ASTM test methods pertaining to certain construction materials (Note 0). Recommended forms for precision and bias statements are included. A discussion of the purpose and significance of these statements for the users of those test methods is also provided. Note 18212;Although under the jurisdiction of Committee C-9, this practice was developed jointly by Committees C-1, D-4, and C-9, and has been endorsed by all three committees. It has subsequently been adopted for use by Committee D-18.

Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials

ASTM E253-03a 材料和产品感官评定的相关标准术语

Standard Terminology Relating to Sensory Evaluation of Materials and Products

ASTM E253-03 材料和产品感官评定的相关标准术语

Standard Terminology Relating to Sensory Evaluation of Materials and Products

ASTM E329-03 施工材料检验和/或检查机构的标准规范

1.1 This specification defines the minimum requirements for inspection agency personnel or testing agency laboratory personnel, or both, and the minimum technical requirements for equipment and procedures utilized in the testing and inspection of materials used in construction.1.2 Criteria is provided for evaluating the capability of agency to properly perform designated tests on construction materials, and establishes essential characteristics pertaining to the organization, personnel, facilities, and quality systems of the agency. This specification may be supplemented by more specific criteria and requirements for particular projects.1.3 This specification can be used as a basis to evaluate an agency and is intended for use in qualifying and/or accrediting agencies, public or private, engaged in the testing and inspection of construction materials. These materials include concrete, steel, soil, masonry and bituminous materials.

Standard Specification for Agencies Engaged in the Testing and/or Inspection of Materials Used in Construction

DIN-Fachbericht 127:2003 从卫生, 健康和环境角度评定建筑产品

Evaluating construction products from a hygiene, health and environmental perspective

ASTM D6237-03 涂漆检查员用标准指南(混凝土和砖石基质)

This guide is intended as a reference for those concerned with the inspection of thin- or thick-film coating application to concrete and masonry substrates. It does not cover the application of cement-type coatings. A checklist is included as Appendix X1.1. Many of the details covered may be in a specification for a particular project. A specification for coating projects should include the coatings to be used.1.1 This guide is intended as an information aid to painting inspectors in carrying out the task efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are pertinent to a particular job.Note 18212;For additional helpful information, refer to the following documents:Manual of Concrete Practice ACI 515R American Concrete InstituteManual of Coating Work for Light Water Nuclear Power Plant Primary Containment and Other Safety Related FacilitiesC 811 Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic SurfacingsSSPC-PA Guide 3 - A Guide to Safety in Paint ApplicationSteel Structures Painting Manual Vol. 1- Good Painting PracticesSteel Structures Painting Manual Vol. 2 - Systems and SpecificationsManufacturers Specifications and Instructions (made available to the inspector for reference to special requirements for proper application)Material Safety Data Sheets (needed to insure that personnel take necessary precautions in handling hazardous materials) Available from Materials manufacturer.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whomever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)

ISO 15148:2002 建筑材料和产品的温湿性能.部分浸入法测定吸水系数

This European Standard specifies a method for determining, by partial immersion with no temperature gradient, the short-term liquid water absorption coefficient. It is intended to assess the rate of absorption of water, by capillary action from continuous or driving rain during on site storage or construction, by insulating and other materials, which are normally protected. The method is suitable for renders or coatings tested in conjunction with the substrate on which they are normally mounted. It is not intended to assess the absorption of water by materials used under water or in overall contact with saturated ground, where a total immersion test is more appropriate.

Hygrothermal performance of building materials and products - Determination of water absorption coefficient by partial immersion