Q15 墙体材料 标准查询与下载

JC/T 239-2014 蒸压粉煤灰砖

本标准规定了蒸压粉煤灰砖的术语和定义、规格、等级和标记、原材料、技术要求、试验方法、检验规则以及产品合格证、堆放和运输。本标准适用于工业与民用建筑用蒸压粉煤灰砖(以下简称砖)。

Autoclaved fly ash brick

JC/T 2298-2014 建筑用膨胀珍珠岩保温板

本标准规定了建筑用膨胀珍珠岩保温板的术语和定义、分类、规格和标记、要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于建筑物外墙外保温系统和防火隔离带用膨胀珍珠岩保温板。

Expanded perlite insulation board for construction

BS 5385-3:2014 墙面砖和地面砖.正常环境中内和外瓷砖和锦砖的设计和铺设.实施规程

This part of BS 5385 gives recommendations for the design,installation and maintenance of floor tiling using ceramic tiles and mosaics bedded on concrete,cement and sand and calcium sulfate-based screeds,timber,flooring grade asphalt and existing hard floor finishes in normal conditions. For special conditions see BS 5385-4.

Wall and floor tiling. Design and installation of internal and external ceramic and mosaic floor tiling in normal conditions. Code of practice

DB53/T 641-2014 蒸压磷石膏砖

本标准规定了蒸压磷石膏实心砖、多孔砖的产品术语和定义、分类、原材料、技术要求、试验方法、检验规则、产品合格证、贮存和运输等。 本标准适用于工业与民用建筑用蒸压磷石膏砖。本标准规定的蒸压磷石膏实心砖可用于防潮层以上的建筑承重部位；蒸压磷石膏多孔砖可用于建筑非承重部位。

Autoclaved Phosphogypsum Bricks

DB43/T 965-2014 水性硅藻泥

Water-based diatom mud

JG/T 172-2014 弹性建筑涂料

本标准规定了弹性建筑涂料的术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于以合成树脂乳液为基料,与颜料、填料和助剂等配制而成的弹性建筑涂料。

Elastomeric wall coatings

DB32/ 2702-2014 蒸压加气混凝土砌块单位产品能耗限额及计算方法

本标准规定了蒸压加气混凝土砌块单位产品能耗术语和定义、能耗限额、统计范围和计算方法及节能管理与措施。 本标准适用于蒸压加气混凝土砌块生产企业能耗的计算、考核和节能管理。 蒸压加气混凝土板材生产企业可参考执行。

Energy consumption limit and calculation method per unit product of autoclaved aerated concrete block

JC/T 2214-2014 钢筋陶粒混凝土轻质墙板

本标准规定了钢筋陶粒混凝土轻质墙板的术语和定义、分类、规格尺寸和标记、一般要求、技术要求、试验方法、检验规则以及标志、包装、运输和贮存。本标准适用于民用与工业建筑非承重内隔墙用的钢筋陶粒混凝土轻质墙板。

Reinforced ceramisite concrete lightweight wallboard

ASTM A951/A951M-14 砌体接缝配筋用钢丝的标准规格

1.1 This specification covers masonry joint reinforcement fabricated from cold-drawn steel wire. Joint reinforcement consists of longitudinal wires welded to cross wires. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Steel Wire for Masonry Joint Reinforcement

ASTM C270-14 砌块用灰浆的标准规格

1.1 This specification covers mortars for use in the construction of non-reinforced and reinforced unit masonry structures. Four types of mortar are covered in each of two alternative specifications: (1) proportion specifications and (2) property specifications. Note 1: When the property specification is used to qualify masonry mortars, the testing agency performing the test methods should be evaluated in accordance with Practice C1093. 1.2 The proportion or property specifications shall govern as specified. 1.3 When neither proportion or property specifications are specified, the proportion specifications shall govern, unless data are presented to and accepted by the specifier to show that mortar meets the requirements of the property specifications. 1.4 This standard is not a specification to determine mortar strengths through field testing (see Section 3). 1.5 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 The terms used in this specification are identified in Terminologies C1180 and C1232. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Mortar for Unit Masonry

DB37/T 5005-2013 水泥聚苯模壳格构式混凝土墙体保温结构一体化应用技术规程

本规程适用于水泥聚苯模壳格构式混凝土墙体保温结构一体化建筑设计、施工及验收等。

Technical specification for integrated application of cement polystyrene formwork lattice concrete wall insulation structure

EN 15286:2013 烧结石料.墙面装饰用墙板和墙砖（内外部）

This European Standard specifies requirements and appropriate test methods for cladding slabs and tiles of agglomerated stone of length or width up to 3500 mm which are made for use as internal and external wall finishes and are either fixed mechanically or glued by adhesive or mortar. It also provides provisions for the evaluation of conformity and marking of these products. This standard does not cover cladding slabs and tiles of agglomerated stone used for internal and external ceiling finishes. In addition, it does not cover slabs and tiles of agglomerated stone intended to be used in suspended ceilings. Products covered by the standards EN 14992, EN 13198, EN 13748-1 and EN 13748-2 are also excluded from the scope of the present standard.

Agglomerated stone - Slabs and tiles for wall finishes (internal and external)

DIN 105-5:2013 粘土砌块.第5部分:轻型水平多孔粘土砌块和轻型横向多孔粘土砌块

Clay masonry units - Part 5: Lightweight horizontally perforated clay masonry units and lightweight horizontally perforated day masonry panels

DIN 105-6:2013 粘土砌块.第6部分:高精度砌块

Clay masonry units - Part 6: High precision units

JC/T 796-2013 回弹仪评定烧结普通砖强度等级的方法

本标准规定了回弹仪评定烧结普通砖强度等级的仪器设备、试样、试验步骤、回弹值的计算和强度等级的评定以及试验报告、本标准适用于不具备GB/T 2542规定试验条件下烧结普通砖(以下简称砖)检验批强度等级的评定;当评定结果有争议时,按GB 5101和GB/T 2542中规定进行强度等级仲裁检验、

The method of evaluating the fired common brick strength grading by rebound hammer

ASTM C62-13a 砌砖(用粘土或页岩制实心砌块)标准规格

1.1 This specification covers brick intended for both structural and nonstructural masonry where external appearance is not a requirement. The brick are prismatic units available in a variety of sizes, shapes, textures, and colors. The specification does not cover brick intended for use as facing units or where surface appearance is a requirement. If brick are required to have a particular color, texture, finish, uniformity, or limits on cracks, warpage, or other imperfections detracting from the appearance they are purchased under Specification C216. This specification does not cover brick intended for use as paving brick (see Specification C902). 1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 4) of this standard is beyond the scope of this standard. 1.3 Brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see Terminology C1232). 1.4 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Building Brick (Solid Masonry Units Made From Clay or Shale)

ASTM C56-13 结构用粘土非承重砖的标准规格

1.1 This specification covers structural clay nonloadbearing tile (partition, fireproofing, and furring). 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of tile extracted from masonry structures for determining conformance or non-conformance to the property requirements (Section 5) of this standard is beyond the scope of this specification. 1.3 Tile covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing and fired bond in Terminology C1232.) 1.4 Fireproofing tile intended for use in load-bearing masonry shall conform to Specification C34. 1.5 Tile intended for use in fireproofing structural members shall be of such sizes and shapes that they can be erected to cover completely the exposed surfaces of the members. 1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Structural Clay Nonloadbearing Tile

ASTM C216-13 饰面砖(粘土或页岩制实心砌块)标准规格

1.1 This specification covers brick intended for use in masonry and supplying structural or facing components, or both, to the structure. 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 7) of this specification is beyond the scope of this specification. 1.3 The brick are prismatic units available in a variety of sizes, textures, colors, and shapes. This specification is not intended to provide specifications for paving brick (see Specification C902). 1.4 Brick are ceramic products manufactured primarily from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). Additives or recycled materials are permitted to be included at the option of the manufacturer. The heat treatment must develop a fired bond between the particulate constituents to provide the strength and durability requirements of this specification (see Terminology C1232). 1.5 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick. 1.5.1 This standard and its individual requirements shall not be used to qualify or corroborate the performance of a masonry unit made from other materials, or made with other forming methods, or other means of binding the materials. 1.6 Three types of brick in each of two grades are covered. 1.7 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)

ASTM C652-13 空心砖(粘土或页岩制空心砌块)的标准规格

1.1 This specification covers hollow building brick and hollow facing brick made from clay, shale, fire clay, or mixtures thereof, and fired to incipient fusion. Four types of hollow brick in each of two grades and two classes are covered. In this specification, the term hollow brick shall be understood to mean hollow clay masonry units whose net cross-sectional area (solid area) in any plane parallel to the surface, containing the cores, cells, or deep frogs, is less than 758201;% of its gross cross-sectional area measured in the same plane (see 4.3). This specification does not cover brick intended for use as paving brick (see Specification C902). 1.2 The property requirements of this specification apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 6) of this standard is beyond the scope of this specification. 1.3 Brick covered by this specification are ceramic products manufactured primarily from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment shall develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. Additives or recycled materials are permitted to be included at the option of the manufacturer. (See “firing” and “firing bond” in Terminology C1232.) 1.3.1 This specification and its individual requirements shall not be used to qualify or corroborate the performance of a masonry unit made from other materials, or made with other forming methods, or other means of binding the materials. 1.4 Hollow brick differ from unglazed structural clay tile (Specifications C34 and C212) and solid brick (Specifications C62 and C216). Hollow brick require greater shell and web thicknesses and higher minimum compressive strength than structural clay tile, but permit greater void area and lesser distance from exposed edge to core hole than solid brick. Therefore, environmental and structural performance may be different in elements constructed of hollow brick from those constructed of structural clay tile or solid brick. 1.5 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.6 The values stated in inch-pound units are to be regarded as standard. The values giv......

Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)

ASTM C410-13 工业用铺地砖的标准规格

1.1 This specification covers brick made from clay or shale or mixtures thereof and are suitable for surfacing industrial floors. Ceramic shapes known as quarry tile are not covered by this specification. 1.2 Terminology related to industrial floor brick is found in Terminology C1232. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Industrial Floor Brick