Q18 装修材料 标准查询与下载

JC/T 2433-2017 建筑装饰板材耐积垢性试验方法

本标准规定了建筑装饰板材耐积垢性试验方法的术语和定义、原理、试验和试验报告。 本标准适用于建筑装饰板材耐积垢性能的测定。

Test method for dirt collection resistance of building decorative panels

DIN EN 15102:2017 装饰墙面涂层.辊子;德文和英文版本prEN 15102-2017

This European Standard applies to wallcoverings in roll form supplied for hanging onto internal walls, partitions or ceilings, by means of an adhesive, whose primary purpose is decorative. However, certain wallcoverings in roll form may confer minor sound absorption and thermal resistance properties. It also provides for the assessment and verification of constancy of performance (AVCP) and marking of these products. It does not apply to wallcoverings whose primary purpose is structural or protective (e. g. vapour or moisture).

Decorative wallcoverings - Roll form; German and English version prEN 15102:2017

EN ISO 11819-2:2017 声学-路面对交通噪声影响的测量-第2部分:接近法(ISO 11819-2:2017)

Acoustics - Measurement of the influence of road surfaces on traffic noise - Part 2: The close-proximity method

DIN EN 233:2017 卷式壁纸.成品壁纸.聚乙烯壁纸和塑料壁纸规范;德文版本EN 233-2016

Wallcoverings in roll form - Specification for finished wallpapers, wall vinyls and plastics wallcoverings; German version EN 233:2016

NF D63-002*NF EN 233:2017 成卷墙纸.墙面用乙烯树脂精制墙纸和塑料墙面饰层的规范.

La présente Norme européenne : spécifie les exigences pour les papiers peints finis, les revêtements muraux vinyles et les revêtements muraux en plastique ;spécifie les exigences pour le marquage ;donne un système de désignation.

Wallcoverings in roll form - Specification for finished wallpapers, wall vinyls and plastics wallcoverings

BS EN 233:2016 卷状墙面覆盖物 成品壁纸、乙烯基墙板和塑料壁纸的规范

Wallcoverings in roll form. Specification for finished wallpapers, wall vinyls and plastics wallcoverings

DB35/T 1592-2016 轻型强化木质装饰板技术条件

本标准规定了轻型强化木质装饰板的术语和定义、分类、要求、检验方法、检验规则以及标志、包装、运输和贮存等。 本标准适用于以0.60 g/cm3 ～0.80 g/cm3 的纤维板为基材，以浸渍胶膜纸为饰面材料的轻型强化木质装饰板。

Specifications for lightweight reinforced wood decorative panels

JC/T 548-2016 壁纸胶粘剂

wallpaper adhesive

JC/T 2375-2016 玻璃纤维增强 树脂中空采光板

Glass fiber reinforced resin hollow lighting panels

JC/T 2376-2016 装饰用轻质发泡铝塑复合板

Lightweight foamed aluminum-plastic composite panels for decoration

PD CEN/TS 16969:2016 油漆和清漆 外部木材的涂层材料和涂层系统 端纹密封性能的评估

This Technical Specification specifies a test method to evaluate the ability of coating materials to seal the end grain of wood against ingress of water. This procedure is relevant for joinery or wood based cladding materials whose service life can depend on the control of water penetration through the coated end-grain.

Paints and varnishes - Coating materials and coating systems for exterior wood - Assessment of end grain sealing performance

EN 13119:2016 幕墙-术语

This European Standard describes terminology used in documents, drawings, specifications etc., when referring to the detailed elements of curtain walling and provides a comprehensive, though not total, list of regular terms. It does not set out to repeat those physical definitions properly included within individual curtain walling standards related to performance requirements and associated test methods.

Curtain walling - Terminology

EN 14019:2016 幕墙-抗冲击-性能要求

This European Standard defines performance requirements of curtain walling under impact load. The mode of breakage of the glass has to be already assessed according to EN 12600. Its criteria are targeted to safety in use and integrity of curtain walling in the event of sudden impact forces on the curtain wall surfaces. Compliance with the performance requirement is determined by the laboratory test. It applies to those areas of curtain walling which face onto areas of human activity, either internally or externally and takes account of accidental impacts brought on by people going about their normal daily activities and impacts brought about by equipment and similar devices for maintenance, cleaning, repair and similar occasional activities. It does not set out to define performance requirements of impact under exceptional circumstances such as acts of vandalism, vehicular collision, firearm projectiles, etc. This standard will have no bearing whatsoever on any National Building / Health and Safety regulations which may exist and whose requirements have to apply separately and in parallel with these test performance requirements.

Curtain Walling - Impact resistance - Performance requirements

DIN EN 61340-4-1:2016 静电学.第4-1部分:对于专门用途的标准试验方法.地板覆盖物和已装地板的电阻(IEC 61340-4-1-2003+A1-2015).德文版本EN 61340-4-1-2004+A1-2015

Electrostatics - Part 4-1: Standard test methods for specific applications - Electrical resistance of floor coverings and installed floors (IEC 61340-4-1:2003 + A1:2015); German version EN 61340-4-1:2004 + A1:2015

DB44/T 1828-2016 瓷质面层再生骨料装饰板

本标准规定了瓷质面层再生骨料装饰板的术语和定义、分类和标记、原材料、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于建筑工程室内外墙面、地面装饰用瓷质面层再生骨料装饰板。

Porcelain facing recycled aggregate decorative board

DB44/T 1829-2016 瓷质面层纤维水泥装饰板

本标准规定了瓷质面层面层纤维水泥装饰板的术语和定义、分类和标记、技术要求、试验方法、检验规则和标志、包装、运输、贮存。 本标准适用于建筑工程室内外墙面和地面用瓷质面层纤维水泥装饰板。

Porcelain facing fiber cement decorative board

EN 13914-1:2016 外部粉刷和内部粉刷的设计,准备和实施.外部粉刷

This European Standard specifies requirements and recommendations for the design, preparation and application of renders based on cement, lime or other mineral binders, and/or combinations thereof, masonry cement and polymer modified binder based external renderings, in accordance with EN 998-1 or site made renders; - renders based on organic binders in accordance with EN 15824 on all common types of backgrounds. It includes rendering on both new and old backgrounds and the maintenance and repair of existing work. This document gives guidance on the use of established site, factory and semi-finished factory made renders. This document does not cover the following: a) the use and application of special renders for liquid retaining structures, e. g. coatings, and for backgrounds to cladding systems; b) the structural repair of concrete; c) the installation of external thermal insulation composite systems (ETICS); d) the specification and use of sealants used to seal joints for use with rendering; e) the use of gypsum based renders used externally, but their use may be permitted in some countries; Gypsum based products soften when subject to prolonged moist conditions. The use of such products externally will depend upon the climatic conditions where the render will be used and on the local building traditions. With the exception of some drier countries in southern Europe gypsum based renders are generally not recommended for external use and are therefore not included within the scope of this document. However, their use may be permitted and controlled locally.1) f) renders on historical monuments or buildings in protected areas which may be regulated by national codes; g) the design and installation of flashings at windowsills and elsewhere. Because of the many and varied materials and practices and different climatic conditions in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country. Appropriate guidance to complement, but not alter any basic European recommendations is given in documentation prepared by each country. Aspects of this European Standard whose basic recommendations may need to be complemented are indicated where they occur by a footnote referencing this clause.

Design, preparation and application of external rendering and internal plastering - Part 1: External rendering

EN 13914-2:2016 室外粉刷和室内粉刷的设计,准备和实施.第2部分:内部粉刷的设计构思和基本原则

This European Standard deals with the design considerations and essential principles for internal plastering systems and application of plastering systems. The different parts of the EN 13914 series of standards specify requirements and recommendations for detailing, design and material considerations, the selection of mixes and the application of gypsum plasters, gypsum/lime plasters, lightweight plasters, lime/gypsum-, cement- and cement/lime-based plasters, lime-based plasters, clay plasters, silicate plasters, organic plasters, polymer-modified plasters, etc. This standard does not deal with the following: - external finishes; - painting and/or preparation; - impregnations; - structural repair of concrete; - prefabricated fibre-reinforced plaster elements. Owing to the many and varied materials and practices and different climatic conditions in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country. Such guidance to complement, but not alter, any basic European recommendations is given in documentation prepared by each country. Aspects of this European Standard, the basic recommendations of which may need to be complemented, are indicated where they occur by a footnote referencing this clause.

Design, preparation and application of external rendering and internal plastering - Part 2: Internal plastering

EN 15468:2016 层压地板覆盖物.直接应用印刷物和树脂表面层的元素.规范,要求和测试方法

This European Standard specifies characteristics, states requirements and gives test methods for laminate floor coverings (as defined in 3.1). It includes a classification system, based on EN ISO 10874, providing practical requirements for areas of use and levels of use, to indicate where laminate floor coverings will give satisfactory service and to encourage the consumer to make an informed choice. It also specifies requirements for marking and packaging. Laminate floor coverings are considered for domestic and commercial levels of use, e. g. in domestic kitchens. This standard does not specify requirements relating to areas that are subject to frequent wetting, such as bathrooms, laundry rooms or saunas.

Laminate floor coverings - Elements with directly applied printing and resin surface layer - Specifications, requirements and test methods

EN 438-6:2016 高压层压装饰制品(HPL).外表基于热固性树脂(通常称为层压制品),第6部分:分类和分层Exterior-grade紧凑的分层厚度大于2毫米和更大的

This European Standard applies to Exterior-grade Compact laminates of thickness 2 mm and greater produced by using a high pressure process. It specifies requirements for standard and flame-retardant laminates intended for use under outdoor weather conditions such as direct sunlight rain and frost. Two levels of performance are specified; one for moderate exterior conditions, and the other for severe exterior conditions. Laminates complying with this European Standard are referred to as Exterior-grade Compact laminates, and are characterized by their high tensile strength, high impact resistance, thermal shock resistance, and resistance to weather and corrosion. They are available in a variety of decorative colours, with high resistance to colour change and aging in outdoor applications. When they are self-supporting Exterior-grade Compact laminates are ready for installation, and only require cutting to size, drilling, etc. to suit the application. EN 438-2 specifies the methods of test relevant to this part of EN 438.

High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 6: Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater