Q22 建筑用塑料制品 标准查询与下载

ANSI Z124.5-1997 塑料便池(抽水箱)座

This Standard covers physical Requirements and test methods for performance pertaining to structure, water resistance, chemical/stain resistance, ignition testing, cleanability,and other significant properties, in addition to general requirements of materials, workmanship and finish of plastic water closet seats and covers.While this standard covers the performance requirements of plastic water closet seats and covers and describes those performance requirements in terms of methods of testapplicable to all such units, a number of different materials and methods of manufacture shall be permitted to be used to meet the requirements.The provisions of this standard are not intended to prevent the use of any alternate material or method of construction provided any such alternate meets the intent of this standard.

Plastic toilet (water closet) seats

DIN EN 652:1997 弹性覆地材料.用软木基作背衬的聚氯乙烯地板铺面.规范

The document specifies the characteristics of floor coverings based on polyvinyl chloride and modifications thereof with a cork-based backing, supplied in either tile or roll form.#,,#

Resilient floor coverings - Polyvinyl chloride floor coverings with cork-based backing - Specification; German version EN 652:1996

ANSI Z124.7-1997 预制塑料壳

Establishes performance standards for plastic spa shells. Intended to serve as a guide for authorities and users and to provide a basis for identifying spa shells that conform to this standard.

Prefabricated plastic spa shells

KS F 2803-1996 保温工程施工标准

이 규격은 연료 공업 제반 장치, 동력 장치, 화학 공업 제반 장치, 공기 조화 설비 및

Standard practice for thermal insulation works

ANSI Z124.4-1996 塑料抽水马桶浮球和水箱

Covers physical requirements and test method for performance and dimensions, in addition to general requirements of materials, workmanship and finish of plastic water closet bowls, tanks, tank covers or combinations of same.

Plastic water closet bowls and tanks

JIS A 5701:1995 玻璃纤维增强塑料瓦楞板

この規格は，主として建築物に用いるがラス繊維で強化したポリエステル彼板(以下,波板という。)について規定する。

Glassfiber reinforced plastic corrugated sheets

JIS A 5721:1995 塑料地板层面板

この規格は，住宅のべランダ，バルコニーなどの床を構成するプラスチックデッキ材（以下,デッキ材という。)についで規定する。

Plastic floor parts

ANSI Z124.2-1995 塑料淋浴器装置

Covers physical requirements and test methods for performance pertaining to structure, water resistance, colorfastness, stain resistance, ignition testing, cleanability, adn other significant properties, in addition to general requirements of materials, workmanship and finish of plastic shower units with walls manufactures integral with the bath or as a multipiece unit distributed as part if the shower unit.

Plastic shower units

JC/T 562-1994 红泥耐候塑料波形板

Red mud weather-resistant plastic corrugated board

JC/T 563-1994 红泥耐候塑料管材和管件

Red mud weather-resistant plastic pipes and fittings

JIS A 5703:1994 室内用塑料层压或印制板

Plastic laminated or printed boards for inside use

JIS A 1415:1994 塑料建筑材料加速暴露老化的试验方法

Recommended practice for accelerated artificial exposure of plastics building materials

BS 4841-3:1994 建筑用硬氨酯泡沫塑料规范.第3部分:组合屋顶顶板隔热用带自动粘附增强饰面的两种层压板(屋顶板)

This Part of BS 4841 specifies requirements for the construction, composition, designation, dimensional tolerances and physical properties of two types of polyurethane (PUR) and polyisocyanurate (PIR) foam cored thermally insulating laminated board (roofboards) with auto-adhesively bonded reinforcing facings and cores not less than 20 mm thick, for use in roofs under built-up bituminized felt roofing materials. This Part of BS 4841 is not applicable to roofboards with reinforcing facings bonded in place after the foaming process has been completed (see clause 4).

Rigid polyurethane (PUR) and polyisocyanurate (PIR) foam for building applications - Specification for two types of laminated board (roofboards) with auto-adhesively bonded reinforcing facings for use as roofboard thermal insulation for built-up roofs

BS 7698-3:1993 往复式内燃机驱动的交流发电机组.第3部分:发电机组用交流发电机规范

This part of ISO 8528 specifies the principal charac-teristics of alternating current (a.c.) generators un-der the control of their voltage regulators when used for generating set applications. It supplements the requirements of IEC 34-1. NOTE 1 At present no International Standard is avail-able for asynchronous generators. When such an Inter-national Standard is published, this part of ISO 8528 will be revised accordingly. See subclause 12.2. This part of ISO 8528 applies to a.c. generators for a.c. generating sets driven by reciprocating internal combustion (RIC) engines for land and marine use, excluding generating sets used on aircraft or to propel land vehicles and locomotives. For some specific applications (for example, essen-tial hospital supplies, high-rise buildings, etc.) sup-plementary requirements may be necessary. The provisions of this part of ISO 8528 should be re-garded as a basis. For a.c. generating sets driven by other reciprocating-type prime movers (e.g. sewage gas engines, steam engines) the provisions of this part of ISO 8528 should be used as a basis.

Reciprocating internal combustion engine driven alternating current generating sets - Specification for alternating current generators for generating sets

ARMY MIL-T-43694 VALID NOTICE 2-1993 地板固定钳制组件

MIL-T-43694(.Ljr dated 16 March 1970, has been reviewed and determined to be valid for use in acquisition.

TIEDOWN ASSEMBLIES, FLOOR ANCHORING

QB/T 1647-1992 无基材聚氯乙烯塑料卷材地板

本标准规定了无基材聚氯乙烯塑料卷材地板(以下简称塑料地板)的产品分类、技术要求、试验方法、检验规则及标志、包装、运输、贮存 本标准适用于以聚氯乙烯树脂为主要原料，加人增塑剂和其他助剂，经压延、印花、复合等工序制成的塑料地板。

Substrate-free PVC plastic sheet flooring

prEN 495-5-1991 热塑性塑料和弹性材料屋面板及密封片.低温折叠试验

Thermoplastic and elastomeric roofing and sealing sheets; low temperature folding test

prEN 495-1-1991 热塑性塑料和弹性材料屋面板及密封片.高温尺寸稳定性的测定

Thermoplastic and elastomeric roofing and sealing sheets; determination of high temperature dimensional stability

prEN 495-3-1991 热塑性塑料和弹性材料屋面板及密封片.耐劈裂压力的测定

Thermoplastic and elastomeric roofing and sealing sheets; determination of split pressure resistance

prEN 495-4-1991 热塑性塑料和弹性材料屋面板及密封片.水蒸汽渗透性能的测定

Thermoplastic and elastomeric roofing and sealing sheets; determination of water vapour transmission properties