Q46 不定型耐火材料 标准查询与下载

JC/T 499-2013 钢纤维增强耐火浇注料

本标准规定了钢纤维增强耐火浇注料的术语和定义、分类和标记、技术要求、试验方法、检验规则以及标志、包装、运输、贮存和质量证明书等。本标准适用于各种热工窑炉用的钢纤维增强耐火浇注料。

Steel-fiber reinforced refractory castable

JC/T 708-2013 耐碱耐火浇注料

本标准规定了耐碱耐火浇注料(简称耐碱浇注料)的术语和定义、分类和标记、技术要求、试验方法、检验规则以及标志、包装、运输、贮存和质量证明书等。本标准适用于各种热工窑炉内衬用具有耐碱性的水硬性浇注料。

Alkali-resistant refractory castable

JC/T 807-2013 轻质耐碱浇注料

本标准规定了轻质耐碱浇注料的术语和定义、分类和标记、技术要求、试验方法、检验规则以及标志、包装、运输、贮存和质量证明书等。本标准适用于各种窑炉耐火、隔热衬里用的具有耐碱性的水硬性浇注料。

Alkali-resistant light-weight castable

JC/T 808-2013 硅铝质耐火浇注料耐碱性试验方法

本标准规定了硅铝质耐火浇注料耐碱性试验方法的原理、仪器设备、试体制备、试验步骤、结果评定和试验报告等。本标准适用于硅铝质耐火浇注料的耐碱侵蚀试验。其他材质的耐火材料耐碱性试验也可参照执行。

Test method for alkali-resistance of silica-alumina refractory castable

JC/T 2127-2012 建材工业用不定形耐火材料施工及验收规范

1.1 本标准规定了建材工业用不定形耐火材料(包括：耐火浇注料、自流浇注料、耐火可塑料、耐火喷涂料、耐火涂抹料等)施工及验收的一般规定、混合料制备、浇注施工、捣打施工、喷射施工、衬里烘烤、检查、修补及验收等技术要求及规范。1.2 本标准适用于建材工业窑炉热工设备用不定形耐火材料的施工技术指导、质量检查和验收：1.3 建材工业用不定形耐火材料的施工及验收，除应符合本规范外，尚应符合国家、行业现行的有关强制性标准及规范的规定。

Code for construction and acceptance of unshaped refractory used in building material industry

YB/T 4319-2012 高炉基建用炭质捣打料

本标准规定了高炉基建用炭质捣打料的定义、分类、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证明书。本标准适用于高炉炉底找平层、水冷管中心线上(下)捣打层、炭砖与炭砖之间及炭砖与冷却设备之间等缝隙填充的高炉基建用炭质捣打料。

Carbon ramming materials for blast furnace construction

YB/T 4320-2012 炭素焙烧炉用不定形耐火材料

本标准规定了炭素焙烧炉用不定形耐火材料(含预制件)的技术要求、试验方法、检验规则、包装、标志、运输、贮存及质量证明书。本标准适用于炭素焙烧炉炉墙用不定形耐火材料(含预制件)。

Monolithic refractories for carbon baking furnace

JC/T 2123-2012 耐火浇注料标准脱模时间试验方法

本标准规定了耐火浇注料标准脱模时间的术语和定义、原理、设备、取样和制样、试验步骤、结果计算和试验报告。本标准适用于耐火浇注料的测定。

Test method for standard measurement of demould time for refractory castable

YB/T 5009-2011 镁质、镁铝质、镁铬质耐火泥浆

本标准规定了镁质、镁铝质、镁铬质耐火泥浆的分类、技术要求、试验方法、质量评定程序、包装、标志、运输、贮存及质量证明书。 本标准适用于砌筑镁砖、镁铝砖、镁铬砖等用的镁质、镁铝质、镁铬质耐火泥浆。

Magnesia，magnesia-alumina，magnesia-chrome refractory mortars

YB/T 384-2011 硅质耐火泥浆

本标准规定了硅质耐火泥浆的分类、技术要求、试验方法、质量评定程序、包装、标志、运输、贮存及质量证明书。 本标准适用于砌筑硅质耐火砖用的硅质耐火泥浆。

Silica refractory mortars

YB/T 4193-2009 抗结皮耐火浇注料

Anti-skinning refractory castable

YB/T 4110-2009 铝镁耐火浇注料

Aluminum-magnesium refractory castable

YB/T 4197-2009 自流耐火浇注料

本标准规定了自流耐火浇注料的术语和定义、分类、技术要求、试验方法、质量评定程序、包装、标志、 运输、储存及质量证明书等。 本标准适用于高铝质、刚玉质、刚玉尖晶石质和铬刚玉质自流耐火浇注料。

Self-flowing refractory castable

ASTM C860-10 通过手中球试验测定耐火浆料坚实度的标准实施规程

This test method is used primarily to determine if a freshly mixed refractory castable is of the proper consistency and therefore would most likely provide optimum performance. It can also be used to estimate the correct water addition rate of a castable when either the manufacturer's specified water content is not available or when unique circumstances have rendered that recommendation unusable. The correct water content is an important factor that must be controlled to obtain optimum castable performance. Excess water can reduce strength, increase volume shrinkage, and promote segregation of the castable ingredients. Insufficient water can produce “honeycombs” (air voids) in the castable because of the insufficient mobility during placement and in extreme cases can prevent the complete hydration of the cement (if used). The Ball-in-Hand test is subjective and somewhat depends on the skill of the operator. However, it is a universally accessible method due to the simplicity of the equipment required, and it is readily used in the field. The total wet mixing time of a castable influences the rheological and final properties and therefore should be monitored. This test method can be performed in a laboratory or on a job site. This test method is not intended to determine the proper consistency for gunning applications, although it may provide information of value for interpretation by a skilled operator.1.1 This test method covers the procedures for determining the consistency of a castable using the Ball-in-Hand Test. The amount of water used in a castable has a significant influence on its performance. 1.2 This test method applies to regular weight castable refractories and insulating castable refractories which are described in Classification C401. It also applies to such castables containing metal fibers. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (See 6.2.3 for a specific safety warning.)

Standard Test Method for Determining the Consistency of Refractory Castable Using the Ball-In-Hand Test

YB/T 4195-2009 防爆裂快速烘烤耐火浇注料

本标准规定了防爆裂快速烘烤耐火浇注料的术语和定义分类、技术要求，试验方法、质量评定程序、 包装、标志、运输、储存及质量证明书等。 本标准适用于轧钢加热炉及其它行业的工业炉用防爆裂快速烘烤耐火浇注料。

Explosion-proof fast-baking refractory castable

ASTM C198-09(2013) 耐火灰浆的冷粘接强度的标准试验方法

3.1 The data developed by this test method show the bonding strength and intrinsic strength of different qualities of air-setting mortar. The procedures described in this test method measure the bonding strength and intrinsic strength of air-setting mortars when used with specific brands or lots of refractory brick. 3.2 Note that it is possible to obtain results with these methods for brick and mortar combinations which are incompatible for use at high operating temperatures. The user must determine this compatibility. Only brick and mortar combinations known or intended to be compatible for a particular use should be tested. 3.3 Properties of the brick, including its strength, apparent porosity, and pore size distribution, can affect the measurement of both the bonding strength of the brick-mortar composite and the intrinsic strength of the mortar. The average modulus of rupture of the test brick, as determined by Test Method C133, should exceed that expected for the mortar being tested. The testing of specific brands or lots of brick and mortar is preferred. 3.4 Three modes of failure are available: the break may occur within the brick itself, at the brick-mortar interface, or within the mortar itself. The latter provides a practical measurement of the strength of the mortar itself and is the predominant mode of failure with the four-point flexure test described. The three-point flexure test measures the failure strength of the brick-mortar composite. Failure within the brick itself suggests that either the particular brick contained a serious flaw, or that the mortar joint strength is of the same magnitude or greater than that of the refractory brick. The mode of failure should always be reported in the final report. 3.5 A ruggedness test for this test method3 performed in 1985 found the following variables to be rugged: specimen size (2.5 to 3.0 in.), mortared surface (cut versus uncut), joint thickness (1/16 to 1/8 in.), pulling of rods (fast versus slow), the loading rate (500 to 1000 lbf/min), the method of load application (3- versus 4-point), and the operator. 3.6 The cold bonding strengths of refractory mortars obtained by this test method are suitable for use in research and development, quality control, and for establishing and evaluating compliance with specifications between producers and consumers. 1.1 This test method covers the determination of the bonding strength of air-setting refractory mortar by determining the flexural strength (modulus of rupture) at room temperature of oven-dried brick-mortar joints. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Cold Bonding Strength of Refractory Mortar

YB/T 4152-2006 氮化物结合耐火材料用耐火泥浆

本标准规定了氮化物结合耐火材料用耐火泥浆的分类、技术要求、试验方法、质量评定程序、包装、标志、运输、储存和质量证明书。 本标准适用于氮化物结合耐火材料砌筑铝电解槽和高炉等用耐火泥浆。

Refractory mortars for nitride bonded refractories

YB/T 4153-2006 高炉用非水系压入料

本标准规定了高炉用非水系压入料的产品分类、技术要求、试验方法、质量评定程序、包装、标志、运输、储存、质量证明书及产品施工说明。 本标准适用于高炉冷却壁与炉壳之间和炉底封板下与碳质捣打料之间填充用非水系压入料。

Non-water injection mix for blast furnace

JIS R 2501:2006 耐火泥(修改件1)

This translation has been made based on the Amendment to the original Japanese Industrial Standard revised by the Minister of Economy, Trade and Industry through deliberations at the Japanese Industrial Standards Committee in accordance with Industrial Standardization Law. Consequently, JIS R 2501:1981 is partially replaced with this Amendment.

Refractory mortars (Amendment 1)

JIS R 2501 AMD 1:2006 耐火泥(修改件1)

JIS R 2501:1981を，次のように改正する。

Refractory mortars (Amendment 1)