共找到 153 条与 不定型耐火材料 相关的标准,共 11 页
Refractory Products - Prepared unshaped materials - Dense and insulating hydraulic cements - Determination of limited temperature of using
Refractory Products - Prepared unshaped materials - Dense and insulating hydraulic cements - Determination of limited temperature of using
Alkali-resistant lightweight castable
Test method for alkali-resistant of alumina-silica castable refractory
Alkali-resistant refractory castable
この規格は,水で煉って使用する耐火モルタルのちょう度試験方法について規定する。
Testing method for cone penetration of refractory mortars
Describes a procedure for comparing the resistance of refractory materials against slag erosion.
Methods of testing refractory materials - Refractory and thermal properties - Determination of resistance to attack by slag (method 1902-513)
This test method is used to estimate the application temperature limits of a refractory mortar and will establish its classification. This test method will be regarded as a pass or fail test because the results are based on observations of whether the mortar flowed from the joints as a result of the heat treatment used. Results obtained by this test method will not agree with those obtained in service when heating is done from only one side. This test method is not applicable for testing nonaqueous mortars. 1.1 This test method covers the determination of refractoriness of all types of refractory mortar by heating a pier of brick laid up with the test mortar to learn whether the prescribed heat treatment causes the mortar to flow out of the joints. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Pier Test for Refractory Mortars
This test method is used to estimate the application temperature limits of a refractory mortar and will establish its classification. This test method will be regarded as a pass or fail test because the results are based on observations of whether the mortar flowed from the joints as a result of the heat treatment used. Results obtained by this test method will not agree with those obtained in service when heating is done from only one side. This test method is not applicable for testing nonaqueous mortars. 1.1 This test method covers the determination of refractoriness of all types of refractory mortar by heating a pier of brick laid up with the test mortar to learn whether the prescribed heat treatment causes the mortar to flow out of the joints. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Pier Test for Refractory Mortars
Refractory products - Unshaped materials - Control of the aptitude of gunning for castables dense and insulating
Refractory products - Unshaped materials - Control of the aptitude of gunning for castables dense and insulating
Refractory products - Prepared unshaped materials control of castables refractories dense and insulating
Refractory products - Prepared unshaped materials control of castables refractories dense and insulating
Shaped refractory products. Sampling and acceptance testing.
この規格は,耐火れんが及び耐火断熱れんが積みに使用ナる熱硬性モルタル(以下,耐火モルタルという。)について規定する。
Refractory mortars
この規格は,耐火モルタルの接着時間試験方法について規定する。
Testing method for setting time of refractory mortars
この規格は,耐火モルタルの粉末度試験方法について規定する。
Testing method for grain size of refractory mortar
この規格は,耐火モルタルの乾燥及び加熱による線変化率試験方法について規定する。
Testing method for coefficient of linear variation of refractory mortar
Alkali-resistant refractory castable
Alkali-resistant lightweight castable
Test method for cone penetration of refractory mortar
Technical Specifications of YZJ-19A Articulated Vibratory Roller
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号