共找到 153 条与 不定型耐火材料 相关的标准,共 11 页
本标准规定了高炉出铁沟浇注料的分类、技术要求、试验方法、质量评定程序、包装、标志、运输、贮存及质量证明书。 本标准适用于高炉主沟、铁沟、渣沟和摆动流槽等部位的工作层耐火浇注料。
Castable for tapping trough of blast furnace
标准规定了循环流化床锅炉用耐磨耐火泥浆的定义、分类、技术要求、试验方法、质量评定程序、包装、标志、运输、贮存及质量证明书。 本标准适用于循环流化床锅炉内砌筑耐磨耐火砖用的泥浆。
Abrasion resistant refractory mortar for circulation fluidized bed boiler
本标准规定了中间包用碱性涂料的分类、技术要求、试验方法、检验规则及包装、标志、运输、贮存和质量证明书。 本标准适用于中间包用碱性涂料。
Basic Coating for Tundish
本标准规定了中间包用挡渣堰的分类、技术要求、试验方法、检验规则、包装、标志、运输、贮存及质量证明书。 本标准适用于中间包用挡渣堰。
Weir for tundish
Test method for explosion resistance of dense refractory castables
本部分规定了致密和嗝热耐火浇注料流动性的定义及测试方法,以及试样制备的成型设备、成型方 法、养护和烘干条件。 本部分适用于致密和嗝热耐火浇注料的流动值测定和试样制备。
Preparation of specimen for unshaped refractories Part1:Refractory castables
Commercial item description A-A-59177, dated 20 March 1998, has been reviewed and determined to be valid for use in acquisition.
MORTAR, REFRACTORY, HEAT-SETTING AND AIR-SETTING WET AND DRY TYPES
1.1 This test method covers the determination of the resistance to deformation or shear of refractory shapes when subjected to a specified compressive load at a specified temperature for a specified time.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Load Testing Refractory Shapes at High Temperatures
The ability of a refractory shapes to withstand prescribed loads at elevated temperatures is a measure of the high-temperature service potential of the material. By definition, refractory shapes must resist change due to high temperature; and the ability to withstand deformation or shape change when subjected to significant loading at elevated temperatures is clearly demonstrated when refractory shapes are subjected to this test method. The test method is normally run at sufficiently high temperature to allow some liquids to form within the test brick or to cause weakening of the bonding system. The result is usually a decrease in sample dimension parallel to the applied load and increase in sample dimensions perpendicular to the loading direction. Occasionally, shear fracture can occur. Since the test provides easily measurable changes in dimensions, prescribed limits can be established, and the test method has been long used to determine refractory quality. The test method has often been used in the establishment of written specifications between producers and consumers. This test method is not applicable for refractory materials that are unstable in an oxidizing atmosphere unless means are provided to protect the specimens. 1.1 This test method covers the determination of the resistance to deformation or shear of refractory shapes when subjected to a specified compressive load at a specified temperature for a specified time. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Load Testing Refractory Shapes at High Temperatures
本标准规定了循环流化床锅炉用耐磨奎火浇注料的定义、分类、技术要求、试验方法,检验规则、包 装、标志、运输、储存及质量证明书。 本标准适用于循环流化床锅炉内衬易冲刷磨损部位用的耐磨耐火浇注料,也适用于其他高温工业窗 爐內襯沖刷磨損嚴重部位用的耐火涯注料。
Abrasion resistant refractory castable for circulation fluidized bed boiler
本标准规定了铝尖唱石硬火江注料的分类、技术要求,试验方法,检验规刚,标志,包装,运输,储存及 质量证明书。 本标准适用于钢包及铁水包衬体等用的铝尖晶石耐火洲注料。
Alumina spinel refractory castable
1.1 This test method covers the determination of the bonding strength of air-setting refractory mortar by determining the flexural strength (modulus of rupture) at room temperature of oven-dried brick-mortar joints. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values stated in SI units are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Cold Bonding Strength of Refractory Mortar
Unshaped refractory products. Determination of complementary properties
Unshaped refractory products. Characterization as received
1.1 This is a quantitative test method applicable to determine the mass percent of uranium isotopes in uranium hexafluoride (UF6) samples. This method as described is for concentrations of 235U between 0.1 and 10 mass percent, and 234U and 236U between 0.0001 to 0.1 mass percent. 1.2 This test method is for laboratory analysis by a gas mass spectrometer with a multi-collector. 1.3 This standard complements C 761, sections 35 through 40, the double-standard method for gas mass spectrometers using a single collector, by providing a method for spectrometers using a multi-collector. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Double-Standard Multi-Collector Gas Mass Spectrometer
Unshaped refractory products. Tests for preformed shapes
Infrared radiation coatings at high temperature
Non-water alumina-silicate refractory mortar
Test method for refractoriness under load of castable refractory.Non-differential,with rising temperature
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号