Q81 供水、排水器材设备 标准查询与下载

BS EN ISO 13257:2017 无压设施用热塑塑料系统.耐高温循环的试验方法

Thermoplastics piping systems for non-pressure applications. Test method for resistance to elevated temperature cycling

T/CADBM 1-2018 聚氯乙烯锁扣地板

本标准规定了聚氯乙烯锁扣地板（以下简称锁扣地板）的术语和定义、产品分类、要求、试验方法、检验规则、标志、运输和贮存。

PVC locking floor

ASME A112.19.1-2018 搪瓷铸铁和搪瓷钢管子附件

Enamelled cast iron and enamelled steel plumbing fixtures

ASME A112.19.2-2018 陶瓷管道固定装置

Ceramic plumbing fixtures

ASTM A888-18 下水管, 雨水管, 污水管和排气管道用无衬套铸铁管和配件

1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. 1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification. 1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.2 1.3.1 Lengths:   Figures EDP/ASA Identification Numbers for Hubless Pipe Fig. 1 10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 11/2 , 2, 3, 4, 5, 6, 8, 10, 12, and 15 in. Fig. 1, Fig. 2 Method of Specifying Fittings Fig. 3 1.3.2 Fittings:  Quarter Bend Fig. 5 Quarter Bend, Reducing

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

ASME B16.29-2017 锻造铜和锻造铜合金焊点排水配件 — DWV

This Standard for wrought copper and wrought copper alloy solder-joint drainage fittings, designed for use with copper drainage tube conforming to ASTM B306, covers the following: (a) description (b) pitch (slope) (c) abbreviations for end connections (d) sizes and method of designating openings for reducing fittings (e) marking (f) material (g) dimensions and tolerances 本标准适用于锻铜和锻铜合金焊点排水配件，设计用于符合ASTM B306的铜排水管，涵盖以下内容： （a） 说明 （b） 坡度（坡度） （c） 端接的缩写 （d） 尺寸和指定用于减少配件的开口的方法 （e） 标记 （f） 材料 （g） 尺寸和公差

Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings — DWV

ISO 21307:2017 塑料管道和配件.聚乙烯(PE)管道系统用对焊熔接程序

This document establishes general principles regarding the procedure used in the construction and quality assessment of butt fusion jointing of polyethylene (PE) piping system components specified in accordance with relevant ISO standards. These components are installed in accordance with the relevant codes of practice, national regulations or industry guidance. Specifically, this document specifies three butt fusion jointing procedures for PE pipes and fittings. These are: — single low-pressure fusion jointing procedure; — dual low-pressure fusion jointing procedure; — single high-pressure fusion jointing procedure. This document takes into consideration the materials and components used, the fusion jointing procedure and equipment and the quality assessment of the completed joint. It can be applied in conjunction with appropriate national regulations and standards. NOTE 1 The references for these procedures are given in the Bibliography.[1][2][3][4][5][6] Single lowpressure fusion jointing procedure is derived from multiple procedures and agreed by experts, given in the Bibliography [1][2]. NOTE 2 The three procedures detailed in this document are based on those most commonly used. It is not the intention that one or more of these procedures be used to replace well established and verified industry based procedures.

Plastics pipes and fittings - Butt fusion jointing procedures for polyethylene (PE) piping systems

JIS C 9335-2-84:2017 家用和类似用途电气设备.安全性.第2-84部分:卫生间设备的详细要求

Household and similar electrical appliances -- Safety -- Part 2-84: Particular requirements for toilets appliances

NF D18-220:2017 卫生阀门.低压恒温混合阀.通用技术规范

Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification

BS 6465-2:2017 卫生器具.第2部分:空间建议.实用规程

Sanitary installations. Part 2: Space recommendations. Code of practice

DIN EN ISO 15876-5:2017 冷热水装置用塑料管道设备.聚丁烯(PB).第5部分:系统的适应性(ISO 15876-5-2017);德文和英文版本EN ISO 15876-5-2017

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017); German and English version EN ISO 15876-5:2017

DIN EN ISO 15876-3:2017 冷热水装置用塑料管道设备.聚丁烯(PB).第3部分:配件(ISO 15876-3-2017);德文和英文版本EN ISO 15876-3-2017

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings (ISO 15876-3:2017); German and English version EN ISO 15876-3:2017

DIN EN ISO 15876-2:2017 热水和冷水装置用塑料管系统.聚丁烯(PB).第2部分:管(ISO 15876-2-2017);德文和英文版本EN ISO 15876-2-2017

Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes (ISO 15876-2:2017); German and English version EN ISO 15876-2:2017

DIN EN ISO 15876-1:2017 热水和冷水装置用塑料管系统.聚丁烯(PB).第1部分:总则(ISO 15876-1-2017);德文版本EN ISO 15876-1-2017

Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General (ISO 15876-1:2017); German and English version EN ISO 15876-1:2017

DIN EN 1253-5:2017 建筑物用集水沟.第5部分:可截流轻液体的集水沟;德文版本EN 1253-5-2017

Gullies for buildings - Part 5: Gullies with light liquids closure; German version EN 1253-5:2017

BS PD CEN/TS 1453-2:2017 建筑物内污物和废水排放(低温和高温)用带结构壁管的塑料管道系统.未增塑的聚氯乙烯(PVC-U).符合性评定指南

Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for the assessment of conformity

DIN EN ISO 4641:2017 给排水用橡胶软管和软管组件.规格(ISO 4641-2016);德文版本EN ISO 4641-2016

Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO 4641:2016); German version EN ISO 4641:2016

DIN EN 13618:2017 饮用水装置软管组件.功能要求和试验方法;德文版本EN 13618-2016

Flexible hose assemblies in drinking water installations - Functional requirements and test methods; German version EN 13618:2016

BS EN ISO 15876-3:2017 冷热水装置用塑料管道系统.聚丁烯.配件

Plastics piping systems for hot and cold water installations. Polybutene (PB). Fittings

BS EN ISO 15876-2:2017 冷热水装置用塑料管道系统.聚丁烯.管道

Plastics piping systems for hot and cold water installations. Polybutene (PB). Pipes