T07 电子计算机应用 标准查询与下载

SAE J1939/71-2009 车辆应用层

As described in the parent document, SAE J1939, there is a minimum of seven documents required to fully define acomplete version of this network. This particular SAE Recommended Practice, SAE J1939-71, describes an ApplicationLayer for vehicle use.

Vehicle Application Layer (Through February 2008)

SAE J1939-71-2009 车辆应用层

As described in the parent document, SAE J1939, there is a minimum of seven documents required to fully define a complete version of this network. This particular SAE Recommended Practice, SAE J1939-71, describes an Application Layer for vehicle use.

Vehicle Application Layer (Through February 2008)

BS ISO 22901-1:2008 道路车辆.开放式诊断数据交换(ODX).数据模型规范

Road vehicles - Open diagnostic data exchange (ODX) - Data model specification

ISO 22901-1:2008 道路车辆.开放式诊断数据交换(ODX).第1部分:数据模型规范

Road vehicles - Open diagnostic data exchange (ODX) - Part 1: Data model specification

SAE J2640-2008 通用汽车嵌入式软件设计要求

The scope of this Recommended Practice encompasses the following objectives: 1) concentrate on the general best practices for vehicular embedded software design; 2) establish programming language-independent best practices; 3) establish hardware/software interface best practices; 4) establish multi-threaded system best practices; 5) provide verification criteria to evaluate product compliance with this best practice.

General Automotive Embedded Software Design Requirements

SAE J272-2008 车辆识别号码系统

1.1 This recommended practice describes general characteristics of VIN systems. It includes certain specific requirements, supporting definitions, basic content, and examples.1.2 The VIN should be considered in the context of a world manufacturer identifier to establish a unique motor vehicle identity.1.3 PurposeThis SAE Recommended Practice provides direction for uniform content and structure of vehicle identification numbers assigned to each type of motor vehicle.

Vehicle Identification Number Systems

SAE J2830-2008 车辆内图标的理解力测试用规程

This document describes a process for testing the comprehension of symbols or icons. Although the process may be used to test any symbols or icons, it has been developed specifically for testing ITS active safety symbols or icons (e.g., collision avoidance), or other symbols or icons that reflect some in-vehicle ITS message or function (e.g., navigation, motorist services, infotainment). Within the process, well-defined criteria are used to identify the extent to which the perceived meaning matches the intended meaning for a representative sample of drivers. Though the process describedbelow reflects a paper-and-pencil approach to conducting the testing, electronic means (i.e., conducted using a computer) can be used as well. The data or results from this process are analyzed to assess the drivers’ comprehension of thesymbol or icon. These data will be used to provide guidance in the design of in-vehicle symbols or icons.

Process for Comprehension Testing of In-Vehicle Icons

GJB 6366-2008 装甲车辆维修检测系统接口要求

本标准规定了装甲车辆维修检测系统接口的类型及要求。 本标准适用于装甲车辆维修检测系统的论证、研制、采购与使用。

Interface requirements of maintenance detecting system for armoured vehicles

SAE J2818-2008 关键词协议1281

This Technical Information Report defines the diagnostic communication protocol Keyword Protocol 1281 (KWP1281). This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an SAE J2534 interface. Some Volkswagen of America and Audi of America vehicles are equipped with ECUs, in which a KWP1281 proprietary diagnostic communication protocol is implemented. The purpose of this document is to specify the KWP1281 protocol in enough detail to support the requirements necessary to implement the communication protocol in an SAE J2534 interface device.

Keyword Protocol 1281

SAE J2012-2007 故障问题的编码定义

This document supersedes SAE J2012 APR2002, and is technically equivalent to ISO 15031-6:2005 with the exceptions described in Section 1.2. This document is intended to define the standardized Diagnostic Trouble Codes (DTC) that On-Board Diagnostic (OBD) systems in vehicles are required to report when malfunctions are detected. This document includes: a. Diagnostic Trouble Code format; b. A standardized set of Diagnostic Trouble Codes and descriptions; c. A standardized set of Dianostic Trouble Codes subtypes known as Failure Types

Diagnostic Trouble Code Definitions

ISO/TS 21308-4:2007 道路车辆.底盘和车身制造商(BEP)之间的产品数据交换.第4部分:STEP应用协议239的绘图

This Technical Specification describes the mapping to STEP application protocol 239 for the exchange of dimensional data between truck chassis manufacturers and bodywork manufacturers. It applies to commercial vehicles, as defined in ISO 3833, which have a maximum gross vehicle mass greater than 3 500 kg. The process of exchanging the above information can involve the chassis manufacturer, the chassis importer, the chassis dealer, one or more bodywork manufacturers, and bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equipment, tipping equipment.

Road vehicles - Product data exchange between chassis and bodywork manufacturers (BEP) - Part 4: Mapping to STEP application protocol 239

KS X ISO 24534-1:2007 机动车辆和设备鉴定.机动车辆电子登记识别(ERI).第1部分:架构

? ??? ??? ??? ???? ??? ???? ????? ????(?:??? ?? ??

Automatic vehicle and equipment identification-Electronic Registration Identification(ERI) for vehicles-Part 1:Architecture

KS X ISO 24534-4:2007 机动车辆和设备鉴定.机动车辆电子登记识别(ERI).第4部分:利用非对称技术的保密通信

? ??? ??? ??? ??? ???? ???? ?? ???? ?? ?? ?? ??(ER

Automatic vehicle and equipment identification-Electronic Registration Identification(ERI) for vehicles-Part 4:Secure communications using asymmetrical techniques

KS X ISO 24534-3:2007 机动车辆和设备鉴定.机动车辆电子登记识别(ERI).第3部分:机动车辆数据

이 규격은 차량에 할당된 식별자에 기초한 전자등록 요구사항을 제공하며(예:국가기관에 의한

Automatic vehicle and equipment identification－Electronic Registration Identification(ERI) for vehicles－Part 3：Vehicle data

KS X ISO 24534-2:2007 机动车辆和设备鉴定.机动车辆电子登记识别(ERI).第2部分:操作要求

이 규격은 차량에 할당된 식별자에 기초한 전자등록 요구사항을 제공하며(예:국가 기관에 의한

Automatic vehicle and equipment identification－Electronic Registration Identification(ERI) for vehicles－Part 2：Operational Requirements

SAE J1939-2007 系列控制和通讯车用网络的推荐实施规程

These Recommended Practices are intended for light, medium, and heavy duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to: on and off highway trucks and their trailers; construction equipment; and agricultural equipment and implements. The purpose of these Recommended Practices is to provide an open interconnect system for electronic systems. It is the intention of these Recommended Practices to allow Electronic Control Units to communicate with each other by providing a standard architecture.

Recommended Practice for a Serial Control and Communications Vehicle Network

SAE J2809-2007 ABS/VSA系统的本田汽车诊断串行数据链路协议

This Technical Information Report defines the proprietary diagnostic communication protocol for ABS or VSA ECU (Electronic Control Unit) implemented on some Honda vehicles. This protocol does not apply to all Honda vehicles. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an enhanced SAE J2534 interface. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an enhanced SAE J2534 interface.

Honda Diagnostic Serial Data Link Protocol ABS/VSA System

KS R ISO 11898-4:2007 道路车辆.控制器局域网络.第4部分:时间触发通信

이 규격은 CAN(Controller Area Network) 내의 타임 트리거 통신(도로

Road vehicles－Controller area network(CAN)－Part 4：Time-triggered communication

KS R ISO 11898-1-1:2007 道路车辆.控制器局域网络.第1部分:数据链层和物理信令

Road vehicles - CAN (Controller Area Network) Part 1: Data link layer and physical signal method

KS R ISO 11898-2:2007 道路车辆.控制器局域网络.第2部分:高速媒体存取单元

이 규격은 CAN(Controller Area Network)의 물리계층을 구성하는 고속(

Road vehicles－Controller area network(CAN)－Part 2：High-speed medium access unit