T10 汽车发动机综合 标准查询与下载

ANSI/ASTM D3306:2001 汽车和轻载装置乙烯乙二醇基引擎冷却剂规范

This specification covers the requirements for ethylene glycol or propylene glycol base engine coolants used in automobiles or other light duty service cooling systems. When concentrates are used at 40 to 70 % concentration by volume in water, or when prediluted glycol base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively to provide protection against freezing, boiling, and corrosion. The coolants governed by this specification are categorized as follows: Note 1 -This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients. This specification shall also apply to engine coolants prepared using glycol generated from recycled or reprocessed used coolant or reprocessed industrial-source glycol, provided that said glycol meets the requirements of Specification E 1177. Separate specifications (D 6471 and D 6472) exist for engine coolants prepared from recycled or reprocessed used coolant or reprocessed industrial-source glycol that does not meet the requirements established in Specification E 1177. The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2 -This specification applies to automobiles and light duty service. Specifications D 4985 and D 6210 exist for heavy duty engine service.

Specification for Ethylene Glycol Base Engine Coolant for Automobile and Light Duty Service

SAE J1343-2000 与卡车和公共汽车发动机附件的循环工作和平均功率要求有关的信息

The objective of this report is to provide information that may be used in obtaining an average power per duty cycle for truck and bus engine accessories. The accessory components covered by this information report include: air brake compressors, alternators, air conditioning compressors, engine cooling fans and drives, and power steering pumps. The values show an estimate of the average power requirements of known duty cycles of these engine drive accessories. This report does not address loads required for engine operation. Required systems include those needed for engine performance such as fuel pumps and electronic control modules (ECM).

Information Relating to Duty Cycles and Average Power Requirements of Truck and Bus Engine Accessories

SAE J2203-1999 SAE 17.6 立方英寸火花塞等级发动机

This SAE Standard defines the standard engine to be used in determining spark plug preignition ratings. The engine is known as the SAE 17.6 Cubic Inch Spark Plug Rating Engine.

SAE 17.6 Cubic Inch Spark Plug Rating Engine

SAE J814-1999 发动机冷却液

This SAE Information Report is a source of information concerning the basic properties of engine coolants which are satisfactory for use in internal combustion engines. Engine coolant concentrate (antifreeze) must provide adequate corrosion protection, lower the freezing point, and raise the boiling point of the engine coolant. For additional information on engine coolants see ASTM D 3306, ASTM D 5216, ASTM D 4985, and ASTM D 6211. The values presented describe desirable basic properties. The results from laboratory tests are not conclusive, and it should be recognized that the final selection of satisfactory coolants can be proven only after a series of performance tests in vehicles. The main body of this document also describes in general the necessary maintenance procedures for all engine coolants to insure proper performance. In addition, special requirements for coolants for heavy-duty engines are covered in Appendix A. This document does not cover maintenance of engine cooling system component parts. That topic is discussed in detail in SAE HS 40.

Engine Coolants

NF R11-415/A1:1999 NF ISO 8856-1997修改件1

Road vehicles. Electrical performance of starter motors. Test methods and general requirements.

QC/T 471-1999 重型汽车柴油机技术条件

本标准规定了重型汽车柴油机的通用技术条件。 　　本标准适用于8L及以上排量的重型汽车柴油机。

Technical conditions for heavy-duty vehicle diesel engines

ANSI/ASTM D6421:1999 通过电子孔燃料注射器污渣评价自动火花点火引擎燃料的试验方法

Test Method for Evaluating Automotive Spark-Ignition Engine Fuel for Electronic Port Fuel Injector Fouling by Bench Procedure

ANSI/ASTM D6471:1999 汽车和轻载装置用可回收预稀释水化乙二醇引擎冷却剂规范

This specification covers the requirements for a recycled prediluted aqueous ethylene glycol (50 volume % minimum) base engine coolant and recycled prediluted aqueous propylene glycol (50 volume % minimum) base engine coolant for use in automobiles and light-duty vehicles. Committee D15 has developed this specification using experience, knowledge and research from recycling used aqueous base engine coolant and blends of used aqueous base engine coolant and virgin glycol. This standard does not apply to coolant produced from other glycol sources such as medical waste, distillation bottoms, airplane/airport deicers and polyester production waste. This specification provides a procedure for evaluating engine coolant recycling technologies through the recycling of a reference synthetic used engine coolant. It also specifies the chemical, physical, and performance requirements for the recycled prediluted aqueous glycol base engine coolant that is produced from that procedure. When used without further dilution, this product functions effectively during both winter and summer. This material is intended to provide protection against freezing, boiling, and corrosion in automobile or other light-duty service cooling systems. The values stated in SI units are to be regarded as the standard. The values given in parentheses are approximate equivalents and provided for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specification for Recycled Prediluted Aqueous Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service

QC/T 525-1999 汽车发动机可靠性试验方法

本标准规定了汽车发动机在台架上进行可靠性试验的基本方法。 　　本标准适用于汽车用往复式内燃机，包括四冲程及二冲程、水冷及风冷、增压及非增压的汽油机和柴油机。 　　凡新设计或重大改进的发动机定型试验、转厂生产的发动机验证试验等均按本标准规定的方法进行。 　　本标准是汽车发动机试验方法的可靠性试验部分，QC/T 524-1999《汽车发动机性能试验方法》系性能试验部分，该标准的有关规定均适用于本标准。

Automobile engine reliability test method

QC/T 526-1999 汽车发动机定型 试验规程

本规程适用于新设计或重大改进的汽车用往复式内燃机，包括四冲程及二冲程、水冷及风冷、增压及非增压的汽油机和柴油机的定型试验。

Automotive Engine Type Test Regulations

QC/T 462-1999 汽车发动机工作小时表

本标准规定了磁感应式汽车发动机工作小时表的技术要求、试验方法和检验规则。 　　本标准适用于汽车用发动机工作小时表。

car engine hours meter

QC/T 277-1999 起动机特性试验方法

本标准适用于汽车、拖拉机、摩托车用起动机的额定数据检查试验。 　　本标准规定了测取起动机在不同负载转矩下的转速、电压、电流等参数，以确定起动机的额定功率及获得起动机特性曲线的方法。

Test method for starter characteristics

SAE J2073-1998 汽车起动器再制造程序

These remanufacturing procedures are recommended minimum guidelines for use by remanufactures of light-duty automotive starters to promote consistent reliability, durability, and safety of remanufactured starters. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though the products may not be identical to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing so as to provide durable operation of the part as well as acceptable performance when installed on the vehicle. The remanufacturer should also consider the safety aspects of the product and any recommendations of the original manufacturers related to remanufacturing or rebuilding their product. While these PROCEDURES are meant to be universal in application, various product types have unique features of dimension and design which may require special remanufacturing processes and tests that are either not covered by or are exceptions to these PROCEDURES.

Automotive Starter Remanufacturing Procedures

BS ISO 2534:1998 道路车辆.发动机试车法规.总功率

This International Standard specifies a method for testing internal combustion engines for propulsion of road vehicles as defined in ISO 3833. It applicable to the evaluation of their performance with a view, in particular, to presenting curves of power and specific fuel consumption at full load as a function of engine speed. This International Standard is applicable to gross power assessment. This International Standard concerns internal combustion engines used for propulsion of passenger cars, trucks and other motor vehicles, excluding motorcycles, mopeds and agricultural tractors normally travelling on roads, and included in one of the following categories: — reciprocating internal combustion engines (spark-ignition or compression-ignition) but excluding free piston engines; — rotary piston engines. These engines may be naturally aspirated or pressure-charged, either using a mechanical supercharger or turbocharger. This International Standard is primarily intended for the communication between the engine manufacturer and the manufacturer of the vehicle. If used for advertising purposes, the ratings must clearly state that they are gross power in accordance with 9.2.

Road vehicles - Engine test code - Gross power

ISO 2534:1998 道路车辆 发动机试验规程 总功率

This International Standard specifies a method for testing internal combustion engines for propulsion of road vehicles as defined in ISO 3833. It applicable to the evaluation of their performance with a view, in particular, to presenting curves of power and specific fuel consumption at full load as a function of engine speed. This International Standard is applicable to gross power assessment. This International Standard concerns internal combustion engines used for propulsion of passenger cars, trucks and other motor vehicles, excluding motorcycles, mopeds and agricultural tractors normally travelling on roads, and included in one of the following categories: — reciprocating internal combustion engines (spark-ignition or compression-ignition) but excluding free piston engines; — rotary piston engines. These engines may be naturally aspirated or pressure-charged, either using a mechanical supercharger or turbocharger. This International Standard is primarily intended for the communication between the engine manufacturer and the manufacturer of the vehicle. If used for advertising purposes, the ratings must clearly state that they are gross power in accordance with 9.2.

Road vehicles - Engine test code - Gross power

QC/T 901-1998 汽车发动机产品质量检验评定方法

本标准规定了汽车用发动机产品质量检验的抽样规定、检验项目、检验方法和评定方法。 　　本标准适用于M类、N类汽车用发动机俄产品质量抽样和监督检验。

Quality inspection and evaluation methods for automobile engine products

NF R11-415:1997 道路车辆.电动机起动器的电性能.试验方法和一般要求

Road vehicles. Electrical performance of starter motors. Test methods and general requirements.

SAE J1375-1997 起动电动机应用考虑

This SAE Recommended Practice identifies some basic and general conditions that should be considered when making electrical starter motor applications.

Starter Motor Application Considerations

SAE J2379-1997 性能发动机建造,推荐做法

This SAE Recommended Practice applies to the function of building reciprocating spark-ignition engines which are used in conjunction with standard and high-performance ancillary components in applications intended to achieve a minimum of 1 hp/in. This document does not apply to rebuilt engines which may only be partially repaired with little or no machining, nor does it apply to second-hand or used engines.

Performance Engine Building Recommended Practices

JIS D 3641-1:1997 柴油发动机.燃料喷射器的测试.第1部分:手柄操作测试和调节设备

この規格は，ディーゼル機関用燃料ィンジェクタに関する，幾つかの試験を行うための手動レバー操作試験及びセッティングの装置について，最小限の要求事項について規定する。

Diesel engines -- Testing of fuel injectors -- Part 1: Hand-lever-operated testing and setting apparatus