T14 润滑、冷却系统与加热装置 标准查询与下载

KS R ISO 9818:2004 乘用车.发动机冷却系统.带限压阀加水口盖的试验方法和标志

이 규격은 승용차의 기관 냉각 장치에서 사용하기 위한 압력 캡의 시험 방법 및 표시 시스템

Passenger cars－Engine cooling systems－Test methods and marking of pressure caps

SAE J1638-2004 软管或实心盘的压缩变形率

This SAE Recommended Practice is used for establishing the compression set that could be expected to occur with a thermoset elastomeric hose under securing clamps. It seeks to reproduce the type of indentation caused by the clamps in the wall of the hose. An excessive compression set measured by this method would indicate a hose that could eventually alloy leakage of fluid or gas past the clamps in service.

Compression Set of Hoses or Solid Discs

SAE J1390-2003 发动机冷却风扇结构分析

Three levels of fan structural analysis are included in this practice: (a) Initial Structural Integrity (b) in-vehicle Testing (c) Durability Test Methods. The Initial Structural Integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The In-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The Durability Test Methods section describes the detailed test procedures that may be used depending on type of fan, equipment availability, and end objective. Each of the previous levels builds upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a new fan design. This SAE Recommended Practice is applicable to medium and heavy-duty trucks, buses, construction equipment, industrial, and agricultural equipment. It does not necessarily include passenger cars and light trucks. The purpose of this document is to identify the general methodology for the structural analysis of engine cooling fans, and to provide expanded information on subset practices within the general methodology, such that a user of this practice can adapt specific subsets related to a vehicle class.

Engine Cooling Fan Structural Analysis

ASTM D6471-03 机动车和轻型车辆用可再循环的预稀释的含水乙二醇基发动机冷却剂(最小50%容量)的标准规范

1.1 This specification covers the requirements for a recycled prediluted aqueous ethylene glycol (50 volume % minimum) base engine coolant and recycled prediluted aqueous propylene glycol (50 volume % min) base engine coolant for use in automobiles and light-duty vehicles. This specification provides a procedure for evaluating engine coolant recycling technologies through the recycling of a reference synthetic used engine coolant. It also specifies the chemical, physical, and performance requirements for the recycled prediluted aqueous glycol base engine coolant that is produced from that procedure. When used without further dilution, this product functions effectively during both winter and summer. This material is intended to provide protection against freezing, boiling, and corrosion in automobile or other light-duty service cooling systems.Note 18212;Committee D15 has developed this specification using experience, knowledge, and research from recycling used aqueous base engine coolants and has not substantially studied the effects of recycling glycols from other sources or with excessive contaminant levels. Efforts are being made to produce a specification for redistilled glycol that addresses recycling used aqueous glycol base engine coolants and glycols from other sources.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are approximate equivalents and provided for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Recycled Prediluted Aqueous Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service

ASTM D6472-03 机动车和轻型车辆用可再循环的乙二醇基发动机冷却剂浓缩物的标准规范

1.1 This specification covers the requirements for recycled ethylene glycol base engine coolant concentrate and recycled propylene glycol base engine coolant concentrate for use in automobiles and light-duty vehicles. This specification provides a procedure for evaluating engine coolant recycling technologies through the recycling of a reference synthetic used engine coolant. It also specifies the chemical, physical, and performance requirements for the recycled glycol base engine coolant concentrate that is produced from that procedure. When used at 40 to 70 volume % in water, it will function effectively during both winter and summer. This material is intended to provide protection against freezing, boiling, and corrosion in automobile or other light-duty service cooling systems.Note 1Committee D-15 has developed this specification using experience, knowledge, and research from the recycling of used aqueous base engine coolants and has not substantially studied the effects of recycling glycols from other sources or with excessive contaminant levels. Efforts are being made to produce a redistilled glycol specification that addresses recycling used aqueous glycol base engine coolants and glycols from other sources.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are approximate equivalents and provided for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Recycled Glycol Base Engine Coolant Concentrate for Automobile and Light-Duty Service

QC/T 288.2-2001 汽车发动机冷却水泵试验方法

本标准规定了汽车发动机冷却水泵的试验项目，试验条件，试验要求及性能参数的测量和计算。 　　本标准适用于汽车发动机冷却水泵。

Test method for automobile engine cooling water pump

QC/T 288.1-2001 汽车发动机冷却水泵技术条件

本标准规定了汽车发动机冷却水泵的技术要求、试验方法、检验规则、标志、包装、运输、贮存等。 　　本标准适用于汽车发动机冷却水泵。

Specifications for automotive engine cooling water pumps

JIS D 1614:2000 汽车散热器.散热性能试验方法

この規格は，自動車用水冷式機関に使用されるエンジン冷却用ラジエータ(以下，ラジエータという。)の放熱性能を試験する方法について規定する。

Radiators for automobiles -- Test method of heat dissipation

QC/T 515-2000 汽车发动机用调温器型式与尺寸

本标准规定了汽车发动机用调温器的型式与尺寸。 　　本标准适用于汽车水冷式发动机调温器;其它用途的发动机调温器也可参照本标准执行。

Type and size of thermostat for automobile engine

SAE J1684-2000 评估冷却系统软管和材料的电化学耐受性的试验方法

This test method provides a standardized procedure for evaluating the electrochemical resistance of automotive coolant hose and materials. electrochemical degradation has been determined to be a major cause of EPDM coolant system hose failures. The test method consists of a procedure which induces voltage to a test specimen while it is exposed to a water/coolant solution. Method No. 1, referred to as a Brabolyzer test, is a whole hose test. Method No. 2, referred to as a U tube test, uses cured plate samples or plates prepared from tube material removed from hose (Method No. 2 is intended as a screening test only). Any test parameters other than those specified in this SAE Recommended practice, are to be agreed to by the tester and the requester.

Test Method for Evaluating the Electrochemical Resistance of Coolant System Hoses and Materials

ASTM D6472-00 机动车和轻型车辆用可再循环的乙二醇基发动机冷却剂浓缩物的标准规范

1.1 This specification covers the requirements for recycled ethylene glycol base engine coolant concentrate and recycled propylene glycol base engine coolant concentrate for use in automobiles and light-duty vehicles. This specification provides a procedure for evaluating engine coolant recycling technologies through the recycling of a reference synthetic used engine coolant. It also specifies the chemical, physical, and performance requirements for the recycled glycol base engine coolant concentrate that is produced from that procedure. When used at 40 to 70 volume % in water, it will function effectively during both winter and summer. This material is intended to provide protection against freezing, boiling, and corrosion in automobile or other light-duty service cooling systems.Note 1Committee D-15 has developed this specification using experience, knowledge, and research from the recycling of used aqueous base engine coolants and has not substantially studied the effects of recycling glycols from other sources or with excessive contaminant levels. Efforts are being made to produce a redistilled glycol specification that addresses recycling used aqueous glycol base engine coolants and glycols from other sources.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are approximate equivalents and provided for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Recycled Glycol Base Engine Coolant Concentrate for Automobile and Light-Duty Service

ASTM D6482-99 用搅拌冷却曲线分析法测定含水聚合物冷却剂的冷却特性的标准试验方法(Tensi法)

1.1 This test method covers the equipment and the procedure for evaluation of quenching characteristics of a quenching fluid by cooling rate determination.1.2 This test method is designed to evaluate quenching fluids with agitation, using the Tensi agitation apparatus.1.3 The values in SI units are to be regarded as the standard. The values in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants by Cooling Curve Analysis with Agitation (Tensi Method)

QC/T 468-1999 汽车散热器技术条件

本标准规定了汽车散热器的技术条件、试验方法、检验规则、包装、标志、运输与贮存。 　　本标准适用于汽车用散热器。

Technical conditions of automobile radiator

ASTM D6471-99 机动车和轻型车辆用可再循环的预稀释的含水的乙二醇发动机冷却剂(最小50%容量)的标准规范

1.1 This specification covers the requirements for a recycled prediluted aqueous ethylene glycol (50 volume % minimum) base engine coolant and recycled prediluted aqueous propylene glycol (50 volume % min) base engine coolant for use in automobiles and light-duty vehicles. This specification provides a procedure for evaluating engine coolant recycling technologies through the recycling of a reference synthetic used engine coolant. It also specifies the chemical, physical, and performance requirements for the recycled prediluted aqueous glycol base engine coolant that is produced from that procedure. When used without further dilution, this product functions effectively during both winter and summer. This material is intended to provide protection against freezing, boiling, and corrosion in automobile or other light-duty service cooling systems.Note 1Committee D-15 has developed this specification using experience, knowledge, and research from recycling used aqueous base engine coolants and has not substantially studied the effects of recycling glycols from other sources or with excessive contaminant levels. Efforts are being made to produce a specification for redistilled glycol that addresses recycling used aqueous glycol base engine coolants and glycols from other sources.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are approximate equivalents and provided for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Recycled Prediluted Aqueous Glycol Base Engine Coolant (50 Volume % Minimum) for Automobile and Light-Duty Service

QC/T 489-1999 机油散热器总成技术条件

本标准适用于汽车、拖拉机、工程机械和固定式、移动式及小型船用内燃机上采用空气冷却的机油散热器总称。

Oil Radiator Assembly Specifications

ANSI/ASTM D2847:1999 汽车和轻型卡车发动机冷却剂测试惯例

This practice covers the procedure for evaluating corrosion protection and performance of an engine coolant in passenger car and light truck service. Note 1 -Coolant evaluation in vehicle service may require considerable time and expense; therefore, the product should be pretested in the laboratory for general acceptability. Tests may vary from small, closely controlled tests, to large tests where close control is not always practical. The units quoted in this practice are to be regarded as standard. The values given in parentheses are approximate equivalents for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7 and Note A1.1.

Practice for Testing Engine Coolants in Car and Light Truck Service

SAE J2296-1998 制冷剂容器的重新测试

To provide a procedure to inspect a refrigerant cylinder used in equipment servicing mobile air-conditioning (A/C) systems. This includes the pressure cylinder used for refrigerant recovery/recycling (R/R) and charging equipment.

Retest of Refrigerant Container

SAE J631-1998 散热器命名规则

This SAE Standard documents nomenclature in common use for various types of radiator and radiator core construction, as well as for various radiator- related accessories.

Radiator Nomenclature

ANSI/ASTM D1882:1998 汽车冷却系统化学溶液对车辆有机面漆影响测试方法

This test method determines the effect of cooling system chemical solutions on organic finishes used on motor vehicles. Cooling system chemicals include: coolants or corrosion inhibitors, or both, cooling system cleaners or flushes, or both, and stop leak additives. Note 1 - This test method is a modification of Practice D 1540. The values stated in SI units are to be regarded as the standard. The values stated in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles

DIN 73411-1:1996-10 汽车冷却管.软管和元件.第1部分:尺寸、材料、类型

Cooling pipes in motor vehicles - Hoses and compounds - Part 1: Dimensions, materials, types