T26 车身（驾驶室）及附件 标准查询与下载
共找到 861 条与 车身（驾驶室）及附件 相关的标准，共 58 页
This SAE Recommended Practice encompasses the significant factors which determine the effectiveness of a seat system in limiting spinal injury during vertical impacts between the rider and the snowmobile seat system. The document is intended to provide a tool for the development of safer snowmobile seats. It is recognized that the seat is only a portion of the entire vehicle protective suspension system. It is, however, usually required that the seat serve as added protection to the suspension system, since the latter may ""bottom out"" during a severe impact. The term ""seat"" refers to the occupant-supporting system not normally considered part of the veh
Dynamic Cushioning Performance Criteria for Snowmobile Seats
- ICS
- 43.040.60;43.160
- CCS
- T26
- 发布
- 2014-04-09
- 实施
- 2018-11-16
S1. Scope. This standard specifies requirements for rear visibility devices and systems.
Transportaion. Part571:Federal motor vehicle safety standards. SubpartB:Federal motor vehicle safety standards. Section571.111:Rear visibility.
- ICS
- CCS
- T26
- 发布
- 2014-04-07
- 实施
- 2014-04-07
本标准规定了汽车座椅套的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于纺织品类和皮革类汽车座椅套。
Car seat cover
- ICS
- 59
- CCS
- T26
- 发布
- 2013-12-08
- 实施
- 2013-12-28
Adhesive film for automotive windows
- ICS
- 43.040.65;83.140.10
- CCS
- T26
- 发布
- 2013-11-20
- 实施
This SAE Standard provides the minimum requirements for Automotive or RV, 7 Position, Self Draining Trailer Tow Connector Interface. The procedures included within this specification are intended to cover the test methods, design, and performance requirements, of the electrical interface of the 7 position trailer tow connector in low voltage (0 to 20) road vehicle applications.
Automotive Trailer Tow Connector
- ICS
- 43.040.10
- CCS
- T26
- 发布
- 2013-11-05
- 实施
- 2016-07-05
This International Standard is intended to define safety requirements which apply to jockey wheels and drawbar supports provided to support the single axle (centre axle) rigid drawbar trailers nose weight with a technically permissible maximum laden mass not more than 3,5 tons.
Road vehicles.Trailers up to 3,5 t.Requirements for jockey wheels and drawbar supports
- ICS
- 43.100
- CCS
- T26
- 发布
- 2013-11
- 实施
本标准规定了汽车安全带织带的术语和定义、要求与试验方法。
Strength requirement and test of automobile safe belt strap
- ICS
- 43.040.60
- CCS
- T26
- 发布
- 2013-10-17
- 实施
- 2014-03-01
本标准规定了汽车车窗玻璃遮阳膜的技术要求、试验方法、检验规则和使用要求等。本标准适用于汽车车窗玻璃遮阳膜的生产和检验,也适用于机动车安全技术检验。
Automotive solar control window films
- ICS
- 43.040.60
- CCS
- T26
- 发布
- 2013-08-22
- 实施
- 2013-12-01
本标准规定了机动车号牌用烫印膜的技术要求、试验方法、检验规则及包装、标志和贮存。本标准适用于机动车号牌用烫印膜的生产与检验。
Hot stamping films for license plates of motor vehicles
- ICS
- 43.040.60
- CCS
- T26
- 发布
- 2013-08-22
- 实施
- 2013-12-01
Pyrotechnic articles - Pyrotechnic articles for vehicles - Part 6: Requirements and categorization for airbag modules (ISO 14451-6:2013); German version EN ISO 14451-6:2013
- ICS
- CCS
- T26
- 发布
- 2013-08
- 实施
Pyrotechnic articles. Pyrotechnic articles for vehicles Requirements and categorization for airbag modules
- ICS
- CCS
- T26
- 发布
- 2013-05-31
- 实施
- 2013-05-31
Pyrotechnic articles. Pyrotechnic articles for vehicles Requirements and categorization for seatbelt pretensioners
- ICS
- CCS
- T26
- 发布
- 2013-05-31
- 实施
- 2013-05-31
Pyrotechnic articles. Pyrotechnic articles for vehicles Requirements and categorization for airbag gas generators
- ICS
- CCS
- T26
- 发布
- 2013-05-31
- 实施
- 2013-05-31
本标准界定了汽车座椅术语及其定义。本标准适用于M类(GB/T 15089-2001)车辆的座椅,也可推广使用于载货汽车、客车的座椅。
Automobile seat terminology
- ICS
- 43.040.60
- CCS
- T26
- 发布
- 2013-04-25
- 实施
- 2013-09-01
本标准规定了汽车内饰件用麻纤维复合板的技术要求、试验方法、检验规则、标志、包装、运输和储存。本标准适用于汽车内饰件用麻纤维复合板。
Technical requirements and test methods of hemp fiber board for automobile interior trim
- ICS
- 43.040.60
- CCS
- T26
- 发布
- 2013-04-25
- 实施
- 2013-09-01
This SAE Recommended Practice specifies performance requirements for the strength of seat belt anchorages attached to vehicle structure or to the seat assemblies as installed in the motor vehicle. (This document supersedes the Performance Requirements Section of SAE J787b.) Design recommendations and test procedures are specified in SAE J383 and SAE J384@ respectively.
Motor Vehicle Seat Belt Anchorages Performance Requirements
- ICS
- 43.040.80
- CCS
- T26
- 发布
- 2013-03-28
- 实施
- 2014-07-10
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice specifies design recommendations for location of seat belt assembly anchorages. It applies to seat belt anchorages attached to vehicle structure or installed to seat assemblies in the vehicle. (This SAE Recommended Practice supersedes the design section of SAE J787b). Performance requirements and test procedures are specified in SAE J385 and SAE J384, respectively.
Motor Vehicle Seat Belt Anchorages Design Recommendations
- ICS
- 43.040.80
- CCS
- T26
- 发布
- 2013-03-28
- 实施
- 2014-10-30
This document has been declared ""Stabilized"" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Recommended Practice outlines static test procedure for the evaluation of the performance of seat belt anchorages attached to vehicle structure or to seat assemblies installed in the vehicle. (This SAE recommended Practice supersedes the Test Procedure Section of SAE 787b.) design recommendations and performance requirements are specified in the recommended Practices SAE J383 and SAE J385, respectively.
Motor Vehicle Seat Belt Anchorages Test Procedure
- ICS
- 43.040.80
- CCS
- T26
- 发布
- 2013-03-28
- 实施
- 2014-10-30
Die vorliegende Norm legt die Arten und die Reihenfolge der anzuwendenden Prufverfahren fur Airbaggasgeneratoren auf fest und legt die entsprechenden Bewertungskriterien fest.
Pyrotechnic articles - Pyrotechnic articles for vehicles - Part 5: Requirements and categorization for airbag gas generators
- ICS
- 43.040.80;71.100.30
- CCS
- T26
- 发布
- 2013-03-01
- 实施
- 2013-03-01
Dieser Teil von ISO 14451 gibt die Arten und die Reihenfolge der anzuwendenden Prufungen fur Anzunder an und legt die Annahmekriterien und Mittel zur Kategorisierung fest. Dieser Teil von ISO 14451 gilt fur Typprufungen. Dieser Teil von ISO 14451 gilt nicht fur Gegenstande, die militarische Explosivstoffe oder kommerzielle Sprengstoffe auser Schwarzpulver oder Blitzsatz enthalten.
Pyrotechnic articles - Pyrotechnic articles for vehicles - Part 8: Requirements and categorization for igniters
- ICS
- 43.040.80;71.100.30
- CCS
- T26
- 发布
- 2013-03-01
- 实施
- 2013-03-01
