W60 针织综合 标准查询与下载

DB41/T 695-2011 针织女裤

knitted women's pants

ASTM D1683/D1683M-11a 机织物缝纫接缝瑕疵的标准试验方法

This test method can also be used to determine either the sewn seam strength of textiles or the efficiency of a seam assembly with any given fabric. Additionally, the seam strengths of different fabrics can be compared directly by using one of the standard seam assemblies specified in Table 1. Because current information about laboratory precision is incomplete, comparative tests may be advisable. In case of dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should perform comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens from the same lot of fabric to be evaluated, which utilize a like seam assembly (or standard seam assembly). The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. If a bias is found, either its cause must be determined and corrected, or the purchaser and supplier must agree to interpret future test results in light of the known bias. This test method determines the seam efficiency of a specified seam assembly with each fabric. Because seam efficiency varies with each fabric, one of the standard seam assemblies, as noted in Table 1, should be used when comparing the seam strength of different fabrics. Table 1 lists the default seam assembly specifications to be used for fabrics made with fine, medium and heavy count yarns. If a determination cannot be made as to which seam is the best suited for a particular fabric, all should be evaluated. Seams prepared for this test method should be made by competent factory sewing operators familiar with the potential for damage to the integrity of the sewn seam when stitching is improperly done. (See Note 2.) Note 38212;If competent factory sewing operators are not accessible, a laboratory technician familiar with the potential for damage of an improperly sewn seam may prepare the seamed test specimens. It is imperative for purchaser/supplier to understand the impact an improperly sewn seam will have on test results. This test method is applicable whenever a determination of effective sewn seam strength, that is, the optimum seam interaction, is required. The breaking force of the seam and fabric will permit determination of seam efficiency. This test method can aid in determining optimum seam interaction for any given fabric by comparing the properties of the fabric with and without seams. Seam engineering techniques for specific fabric types can also be determined by utilizing this test method. This test method can be used to determine when the sewn seam is affected by seam slippage. While the ultimate consequence of this phenomenon is rupture, seam slippage greater than either the values stated in customer specifications, or as agreed upon by purchaser/supplier may severely reduce the integrity such that the product cannot be used for its intended purpose. (An example of a commonly used seam slippage value is 6 ± 1 mm [0.25 ± 0.04 in.]).1.1 This test method measures the sewn seam strength in woven fabrics by applying a force perpendicular to the sewn seams. Note 18212;The grab test procedure in Test Method D5034 shall be used to determine any characteristic in fabric that can affect the measurement of sewn seam strength. 1.1.1 This test method is applicable to sewn seams obtained from a previously sewn article or seams sewn with fabric samples u......

Standard Test Method for Failure in Sewn Seams of Woven Apparel Fabrics

KS K ISO 8388:2010 针织物.类型.词汇.两种语言版

이 표준은 산업용 기계 편성물의 용어에 대해 정의한다.정의된 용어는 그 자체로 완전

Knitted fabrics-Types-Vocabulary

SN/T 1931.6-2009 进出口机织物检验规程 第6部分:麻及麻混纺机织物

SN/T 1931的本部分规定了进出口麻及麻混纺机织物的抽样、检验及结果评定。 本部分适用于进出口麻及麻混纺机织物的检验。

Rules for the inspection of woven fabric for import and export.Part 6:Textile bast fibres and woven fabrics,mixed

DIN EN ISO 23606:2009 纺织品.针织织物.表示法和图案设计(ISO 23606:2009),DIN EN ISO 23606:2009-08的英文版本

This International Standard specifies various systems of symbolic notation and pattern design for knitted fabrics. The symbolic notations contained in this International Standard do not necessarily constitute the only method of representation.

Textiles - Knitted fabrics - Representation and pattern design (ISO 23606:2009); English version of DIN EN ISO 23606:2009-08

KS K 0813-2009 毯子易燃性试验法

이 표준은 담요용 천이나 담요의 가연성 시험방법에 대하여 규정한다.

Test method for flammability of blankets

KS K 0833-2009 纽扣的腐蚀试验法

이 표준은 금속 성분이 있는 스냅의 녹 혹은 부식성을 측정하기 위한 시험방법에 대하여 규정

Test method for snap corrosion

KS K 0830-2009 塑料钮扣耐久性试验法:冲击力

이 표준은 일정한 충격 강도에 의해 플라스틱 단추(이하 단추라 한다.)가 어느 정도의 내구

Test method for durability of the plastic buttons to impact force

KS K 0819-2009 门帘材料的光遮蔽性能测试法

이 표준은 섬유제 커튼 및 커튼용 천의 차광 성능을 평가하기 위한 시험방법에 대하여 규정한

Test method for light blocking effect of curtain materials

JIS L 1901:2009 机织品和针织品纱线因反转起毛面的试验方法

This Standard specifies the testing methods for frosting due to yarn reversing in wet state of the woven and knitted fabrics which have been dyed.

Testing methods for frosting due to yarn reversing of woven and knitted fabrics

ASTM D3691/D3691M-09 机织带状针织家用窗帘和带皱折编织物的标准性能规范

Fabrics intended for this end-use should meet all of the requirements listed in Table 1. It should be recognized that fabric can be produced utilizing an almost infinite number of construction variables (e.g., type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finished). Additionally, fashion and aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1. Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. TABLE 1 Performance Requirements Characteristics Knit and LaceSheer (woven)Foam Back, Stitch Bonded, and Conventional Weights (woven)Section Breaking strength (load), (CRT method), in both directionsA... 67 N (15 lbf), min89 N (20 lbf), min 5.1 Bursting strength (ball burst)A 138 kPa (20 lbf/in.2), min ... ... 5.2 Tear strength (tongue tear), in both directionsA...4.4 N (1 lbf), min6.7 N (1.5 lbf), min 5.3 Dimensional change: After 5 launderings in both directions3.0 % max +0.0%3.0 % max 0.0%3.0 % max +0.0% 5.4.1 After 3 dry cleanings in both directions3.0 % max +0.0%3.0 % max +0.0%3.0 % max +0.0 % 5.4.2 Distortion of yarn: 1-lbf load...2.54 mm (0.1 in.), max...

Standard Performance Specification for Woven, Lace, and Knit Household Curtain and Drapery Fabrics

SN/T 1931.5-2008 进出口机织物检验规程.第5部分:棉及棉混纺机织物

SN/T 1931的本部分规定了进出口棉及棉混纺机织物的技术要求、检验和检验结果的判定。 本部分适用于衣着用的棉及棉混纺机织物的检验。

Rules for the inspection of woven fabric for import and export.Part 5:Cotton and blended cotton woven fabircs

KS K 0820-2008 羽绒制品试验法

이 규격은 우모1)의 시험방법에 대하여 규정한다.

Test methods for feather and down

KS K 0815-2008 针织品的试验方法

이 규격은 편성물1)의 시험방법에 대하여 규정한다.

Test methods for knitted fabrics

ASTM D3882-08e1 编织物和针织物中扭纹和斜纹的标准试验方法

This test method is considered satisfactory for acceptance testing of commercial shipments. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. Other fabrics with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. Individual rolls are normally accepted or rejected on the basis of the maximum amount of bow or skew in a specific roll of fabric. The average bow or skew in a roll or lot or the range of bow or skew in a roll may be determined but are not normally used in the trade for acceptance or rejection. Bow or skew can be induced during fabric manufacturing, dyeing, tentering, finishing, or other operations where a potential exists for uneven distribution of tensions across the fabric width. Bow and skew are more visually displeasing in colored, patterned fabrics such as plaids and horizontal stripes rather than in solid colors because the contrast makes the distortion more prominent. These defects may cause sewing problems in such fabrics and draping problems in finished products. In some cases, a specified amount of skew is needed, for example, to prevent twisting of pant legs made of twill fabric. Matching plaids from distorted patterns may create serious problems for the garment manufacturer or home sewer. Wavy or sharp breaks in the bow line are more detrimental to the appearance of small parts of a garment (such as collars, pockets, and so forth) than a gradual slope from a straight line. 5.3.1 Automotive interior textiles used for seat bolsters, cushions, headrests and door panels may be susceptible to bow and skew, especially when visually patterned fabrics are joined or mated to a straight edge surface.1.1 This test method covers the determination of bow and skew of filling yarns in woven fabrics and the courses in knitted fabrics. 1.2 This test method can also be used to measure the bow and skew of printed geometric designs. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Bow and Skew in Woven and Knitted Fabrics

ASTM D3775-08 机织物纬纱和经纱计数的标准试验方法

This test method is considered satisfactory for acceptance testing of commercial shipments because it has been used extensively in the trade for that purpose. If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use the samples for such a comparative test that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.1.1 This test method covers the measurement of warp end count and filling pick count and is applicable to all types of woven fabrics. Note 18212;Historically, the term fabric count has been used to describe the end and pick count of woven fabrics. The terms warp (end) and filling (pick) count are replacing the term fabric count, to provide clarity. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Warp (End) and Filling (Pick) Count of Woven Fabrics

ASTM D3882-08 机织和针织织物中弓纬和纬斜的标准试验方法

This test method is considered satisfactory for acceptance testing of commercial shipments. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. Other fabrics with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. Individual rolls are normally accepted or rejected on the basis of the maximum amount of bow or skew in a specific roll of fabric. The average bow or skew in a roll or lot or the range of bow or skew in a roll may be determined but are not normally used in the trade for acceptance or rejection. Bow or skew can be induced during fabric manufacturing, dyeing, tentering, finishing, or other operations where a potential exists for uneven distribution of tensions across the fabric width. Bow and skew are more visually displeasing in colored, patterned fabrics such as plaids and horizontal stripes rather than in solid colors because the contrast makes the distortion more prominent. These defects may cause sewing problems in such fabrics and draping problems in finished products. In some cases, a specified amount of skew is needed, for example, to prevent twisting of pant legs made of twill fabric. Matching plaids from distorted patterns may create serious problems for the garment manufacturer or home sewer. Wavy or sharp breaks in the bow line are more detrimental to the appearance of small parts of a garment (such as collars, pockets, and so forth) than a gradual slope from a straight line. 5.3.1 Automotive interior textiles used for seat bolsters, cushions, headrests and door panels may be susceptible to bow and skew, especially when visually patterned fabrics are joined or mated to a straight edge surface.1.1 This test method covers the determination of bow and skew of filling yarns in woven fabrics and the courses in knitted fabrics. 1.2 This test method can also be used to measure the bow and skew of printed geometric designs. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Bow and Skew in Woven and Knitted Fabrics

JIS L 1076 ERRATUM 1:2007 勘误表

ERRATUM

SANS 6104:2007 纬编针织物的线迹长度

Specifies a method for the determination of the stitch length of regular weft-knitted fabrics.

Stitch length of weft-knitted fabrics

FZ/T 70010-2006 针织物平方米干燥重量的测定

本标准规定了针织物平方米干燥重量的测定方法。 本标准适用于各类针织物。

Testing method of dry weight per unit area for knitted fabrics