W60 针织综合 标准查询与下载

JIS L 1076:2006 机织品和针织品疵点的测试方法

この規格は，織物及ぴ編物のピリング試験方法について規定する。

Testing methods for pilling of woven fabrics and knitted fabrics

BS EN 14971:2006 织物.针织物.测定每个单元长度和面积上的针脚量

This test method determines the number of wales and courses per centimetre in most knitted fabrics.

Textiles - Knitted fabrics - Determination of number of stitches per unit of length and unit area

BS EN 14970:2006 织物.针织物.测定线迹长度和纬编针织绸纱线线密度

This European Standard specifies test methods for the determination of stitch length and yarn linear density of a weft knitted fabric. They can be applied to warp knitted fabrics, if it is possible to de-knit the fabric. The measurements will be applied to yarns from each knitting machine feeder and/or different patterning courses. The results can be used for the analysis of fabric fault, e.g. barré analysis.

Textiles - Knitted fabrics - Determination of stitch length and yarn linear density in weft knitted fabrics

SANS 6120:2005 针织织物单位长度上的经圈和纬圈数（固定光阑法）

Specifies the fixed aperture method for the determination of the number of wales and courses per unit length in knitted textile fabrics.

Wales and courses per unit length in knitted textile fabrics (fixed aperture method)

SANS 5370:2005 针织品在松弛状态的尺寸变化

Specifies a method for the determination of the dimensional changes of hosiery during relaxation.

Dimensional changes of hosiery during relaxation

SANS 5369:2005 针织品的尺寸

Specifies a method for the determination of the dimensions of hosiery.

Dimensions of hosiery

DIN 62050:2005 针织物.表示法和图案设计

This standard is applicable to knitted fabrics. It determines the forms of presentation and their pattern design.

Knitted fabrics - Presentation and pattern design

DIN 61211:2005 缝编机织生产的织物.工艺分级和定义

Textile fabrics produced by stitch-bonding machines - Technological classification, definitions

FZ/T 70006-2004 针织物拉伸弹性回复率试验方法

本标准规定了用定伸长和定力法测定针织物的拉伸弹性变形和塑性变形的试验方法。 本标准适用于各种针织物。

Stretch and recovery testing method for knits

ASTM D2594-04(2008)e2 低弹针织物弹性的标准试验方法

This test method specifies test conditions for measuring the fabric growth and fabric stretch of knitted fabrics intended for use in swimwear, anchored slacks, and other form-fitting apparel (also commonly known as semi-support apparel) applications, as well as test conditions for measuring the fabric growth of knitted fabrics intended for use in sportswear and other loose-fitting apparel (also commonly known as comfort stretch apparel) applications. The applicability of this test method to the measurement of fabric growth and fabric stretch of knitted fabrics intended for use in slacks, sport coats, and suits has not been determined. This test method is not recommended for acceptance testing of commercial shipment because the between-laboratory precision is known to be poor. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results are obtained, and are assigned randomly in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.1.1 This test method covers the measurement of fabric stretch and fabric growth of knitted fabrics intended for applications requiring low-power stretch properties. 1.2 This test method includes procedures for fabric growth and stretch and can be used individually when required by individual specifications. 1.3 This test method is not applicable to fabrics intended for support or other applications requiring high-power stretch properties. Note 18212;For information on testing high-power and woven stretch fabrics, refer to Test Methods D3107 and D6614. 1.4 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Stretch Properties of Knitted Fabrics Having Low Power

ASTM D2594-04 低弹针织品弹性的标准试验方法

This test method specifies test conditions for measuring the fabric growth and fabric stretch of knitted fabrics intended for use in swimwear, anchored slacks, and other form-fitting apparel (also commonly known as semi-support apparel) applications, as well as test conditions for measuring the fabric growth of knitted fabrics intended for use in sportswear and other loose-fitting apparel (also commonly known as comfort stretch apparel) applications. The applicability of this test method to the measurement of fabric growth and fabric stretch of knitted fabrics intended for use in slacks, sport coats, and suits has not been determined. This test method is not recommended for acceptance testing of commercial shipment because the between-laboratory precision is known to be poor. 5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results are obtained, and are assigned randomly in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.1.1 This test method covers the measurement of fabric stretch and fabric growth of knitted fabrics intended for applications requiring low-power stretch properties. 1.2 This test method includes procedures for fabric growth and stretch and can be used individually when required by individual specifications. 1.3 This test method is not applicable to fabrics intended for support or other applications requiring high-power stretch properties. Note 1-For information on testing high-power stretch fabrics, refer to Test Method D 1775. 1.4 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Stretch Properties of Knitted Fabrics Having Low Power

ASTM D3883-04(2012) 机织织物中纱线卷曲性或织缩性的标准试验方法

The relationship of the length of a piece of fabric and the length of yarn in the fabric can be determined accurately only be measuring the length of yarn entering the loom and the length of fabric made from that particular length of yarn. In most cases, however, the determination must of necessity be made on a woven fabric by measuring the length of yarn removed from a measured length of fabric, thus introducing certain variations that will influence the accuracy of the test. Yarn removed from the woven fabric contains undulations or waves that have been introduced by the weaving process. Heat, moisture, and mechanical shrinkage on subsequent finishing operations may accentuate these undulations, and in all probability, increase the force to pull them out and straighten the yarn. In order to accurately measure the length of the yarn after the removal of the crimp, these undulations must be pulled out without elongating the yarn. In some cases, the minimum force necessary to straighten the yarn will cause a certain amount of the elongation to take place, thus increasing the length of the yarn. Also, stresses imposed upon the yarn during the weaving process may have been sufficient to stretch the yarn beyond its elastic limit, again increasing its length. It is recognized that determination made by measuring length of yarn removed from a measured length of fabric may tend to give crimp values that are somewhat higher than the crimp in the yarn as it lay in the fabric. In the case of fabrics made from yarns that exhibit differential shrinkage, or yarns of widely different count, or yarns woven at different tensions, the crimp of each type of yarn in the fabric must be determined and reported separately. This test method can be used for acceptance testing of commercial shipments but comparisons should be made with caution because information on estimates of between-laboratory precision is limited as noted in 13.1. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.1.1 This test method covers the determination of the relationship between the length of a piece of fabric and the length of the yarn in the fabric by measurement of the yarn crimp and yarn take-up. 1.2 This test method applies to woven fabrics. 1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Yarn Crimp and Yarn Take-up in Woven Fabrics

ASTM D2594-04(2012) 低弹针织物弹性的标准试验方法

This test method specifies test conditions for measuring the fabric growth and fabric stretch of knitted fabrics intended for use in swimwear, anchored slacks, and other form-fitting apparel (also commonly known as semi-support apparel) applications, as well as test conditions for measuring the fabric growth of knitted fabrics intended for use in sportswear and other loose-fitting apparel (also commonly known as comfort stretch apparel) applications. The applicability of this test method to the measurement of fabric growth and fabric stretch of knitted fabrics intended for use in slacks, sport coats, and suits has not been determined. This test method is not recommended for acceptance testing of commercial shipment because the between-laboratory precision is known to be poor. If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results are obtained, and are assigned randomly in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.1.1 This test method covers the measurement of fabric stretch and fabric growth of knitted fabrics intended for applications requiring low-power stretch properties. 1.2 This test method includes procedures for fabric growth and stretch and can be used individually when required by individual specifications. 1.3 This test method is not applicable to fabrics intended for support or other applications requiring high-power stretch properties. Note 18212;For information on testing high-power and woven stretch fabrics, refer to Test Methods D3107 and D6614. 1.4 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Stretch Properties of Knitted Fabrics Having Low Power

ASTM D2594-04(2016) 低功率针织物拉伸性能的标准试验方法

5.1 This test method specifies test conditions for measuring the fabric growth and fabric stretch of knitted fabrics intended for use in swimwear, anchored slacks, and other form-fitting apparel (also commonly known as semi-support apparel) applications, as well as test conditions for measuring the fabric growth of knitted fabrics intended for use in sportswear and other loose-fitting apparel (also commonly known as comfort stretch apparel) applications. The applicability of this test method to the measurement of fabric growth and fabric stretch of knitted fabrics intended for use in slacks, sport coats, and suits has not been determined. 5.2 This test method is not recommended for acceptance testing of commercial shipment because the between-laboratory precision is known to be poor. 5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if their is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results are obtained, and are assigned randomly in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. 1.1 This test method covers the measurement of fabric stretch and fabric growth of knitted fabrics intended for applications requiring low-power stretch properties. 1.2 This test method includes procedures for fabric growth and stretch and can be used individually when required by individual specifications. 1.3 This test method is not applicable to fabrics intended for support or other applications requiring high-power stretch properties. Note 1: For information on testing high-power and woven stretch fabrics, refer to Test Methods D3107 and D6614. 1.4 The values stated in either SI or inch-pound units are to be regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Stretch Properties of Knitted Fabrics Having Low Power

ISO 8499:2003 针织物.疵点的描述.词汇

This International Standard describes defects which commonly appear during the inspection of knitted fabrics. A defect is a fault that would reduce the expected performance of the knitted fabric or, if it appeared in a prominent position in an article made from the fabric, would readily be seen and rejected by a prospective purchaser. Except where otherwise stated the descriptions apply to defects appearing in both weft-knitted and warp-knitted fabrics. NOTE In addition to terms used in two of the three official ISO languages (English and French), this International Standard gives the equivalent terms in the German language in Annex A; these are published under the responsibility of the member body for Germany (DIN). However, only the terms and definitions given in the official languages can be considered as ISO terms and definitions.

Knitted fabrics - Description of defects - Vocabulary

DIN EN ISO 8388:2003 针织物.类型.词汇

The project defines terms for industrially produced maschine knitted fabrics.

Knitted fabrics - Types - Vocabulary (ISO 8388:1998); German version EN ISO 8388:2003

BS EN ISO 4921:2002 针织.基本概念.词汇表

This International Standard defines terms for basic knit-ting concepts. The definitions of this vocabulary are complete in them-selves; illustrations are used to clarify the content of a definition, but no standardization of any notational sys-tem is attempted.

Knitting. Basic concepts. Vocabulary

SANS 4921:2000 针织．基本概念．词汇

Defines terms for basic knitting concepts.

Knitting - Basic concepts - Vocabulary

JIS K 7137-2:2001 塑料.聚四氟乙烯(PTFE)半成品.第2部分:试验样品制备和性能测定

この規格は，PTFEの試験片の作り方及びPTFE素材に要求される測定方法について規定する。

Plastics -- Polytetrafluoroethylene (PTFE) semi-finished products -- Part 2: Preparation of test specimens and determination of properties

ASTM D3787-01 针织品破裂强度测试方法.恒速横向移动球式破裂试验

1.1 This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.1.2 The values stated in SI units are to be regarded as the standard.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the test, the inch-pound units are shown in parenthesis. The values stated in each system are not exact equivalents; therefore, each system may be used independently of the other. Combining values from the two systems may result in nonconformance within the specification.Note 18212;For the measurement of bursting strength with a hydraulic testing machine, refer to Test Method D 3786.1.4 This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to us.

Test Method for Bursting Strength of Textiles-Constant-Rate-of-Traverse (CRT) Ball Burst Test