Y26 日用搪瓷制品 标准查询与下载

JIS S 6052:1987 搪瓷标志板

この規格は，描写面がほうろうで仕上げられ，白板用のツーキノダべン(以下，マ一カ一という。)で描写するために用いる屋内用の白板(以下，白板という。)にりいて規定する。

Porcelain-enameled marker board

ASTM C743-87(2014)e1 搪瓷涂层连续性的标准试验方法

1.1 Porcelain enamel coatings are applied to metals to provide protection from corrosion as well as to enhance their appearance. This test method permits the easy detection of discontinuities and areas of light coverage, not readily seen by visual inspection, which limit the protection to the substrate. Somewhat similar tests applicable to the thicker glass coatings used for chemical reaction vessels are found in Test Methods C536 and C537. 1.2 Values stated in SI units are to be regarded as the standard. Inch-pound units are provided for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Continuity of Porcelain Enamel Coatings

ASTM C743-87(2009) 搪瓷涂层连续性的标准试验方法

1.1 Porcelain enamel coatings are applied to metals to provide protection from corrosion as well as to enhance their appearance. This test method permits the easy detection of discontinuities and areas of light coverage, not readily seen by visual inspection, which limit the protection to the substrate. Somewhat similar tests applicable to the thicker glass coatings used for chemical reaction vessels are found in Test Methods C 536 and C 537. 1.2 Values stated in SI units are to be regarded as the standard. Inch-pound units are provided for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Continuity of Porcelain Enamel Coatings

ASTM C743-87(2004)e1 搪瓷涂层连续性的标准试验方法

1.1 Porcelain enamel coatings are applied to metals to provide protection from corrosion as well as to enhance their appearance. This test method permits the easy detection of discontinuities and areas of light coverage, not readily seen by visual inspection, which limit the protection to the substrate. Somewhat similar tests applicable to the thicker glass coatings used for chemical reaction vessels are found in Test Methods C 536 and C 537.1.2 Values stated in SI units are to be regarded as the standard. Inch-pound units are provided for information only.This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Continuity of Porcelain Enamel Coatings

ASTM C538-83(2009) 红色、橙色和黄色陶瓷色牢度的标准试验方法

Correlation between results of this test and outdoor exposure tests of porcelain enamels colored with cadmium sulfo-selenide pigment shows that the cupric sulfate test is an effective indicator of the tendency for such coatings to experience appreciable color changes during weathering. The cupric sulfate test is considered useful for specification acceptance, quality control, and research and development purposes. 1.1 This test method covers only porcelain enamels containing the cadmium-sulfide or cadmium sulfo-selenide types of pigments. The purpose of the test is to detect those red, yellow, orange, and some green porcelain enamels that are likely to experience appreciable color changes upon exposure to atmospheric corrosion. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Color Retention of Red, Orange, and Yellow Porcelain Enamels

ASTM C538-83(2004)e1 红色、橙色和黄色陶瓷色牢度的试验方法

Correlation between results of this test and outdoor exposure tests of porcelain enamels colored with cadmium sulfo-selenide pigment shows that the cupric sulfate test is an effective indicator of the tendency for such coatings to experience appreciable color changes during weathering. The cupric sulfate test is considered useful for specification acceptance, quality control, and research and development purposes. 1.1 This test method covers only porcelain enamels containing the cadmium-sulfide or cadmium sulfo-selenide types of pigments. The purpose of the test is to detect those red, yellow, orange, and some green porcelain enamels that are likely to experience appreciable color changes upon exposure to atmospheric corrosion.

Standard Test Method for Color Retention of Red, Orange, and Yellow Porcelain Enamels

ASTM C839-82(2005) 用负载梁法测定搪瓷的压缩应力标准试验方法

All porcelain enamel coatings or glass coatings are by necessity under some degree of compression at room temperature. The desired degree of compression or stress depends upon the type of ware and the end use of the item. Some method of determining relative compressive stress of enamels is necessary to establish the suitability of an enamel for a proposed application. 1.1 This test method covers the measurement of the compressive stresses (Note 0) developed by fired porcelain enamels using the loaded-beam method. Note 0Although some may interpret the calculations that are used in this test method as indicating compressive load, it is commonly referred to as compressive stress within the porcelain enamel industry.1.2 This test method is limited to the use of the loaded-beam method. However, this method includes charts ( and ) that provide for conversion of loaded-beam test results to warp and ring stress values.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Compressive Stress of Porcelain Enamels by Loaded-Beam Method

ASTM C839-82(2010) 用负载梁法测定搪瓷的压缩应力标准试验方法

All porcelain enamel coatings or glass coatings are by necessity under some degree of compression at room temperature. The desired degree of compression or stress depends upon the type of ware and the end use of the item. Some method of determining relative compressive stress of enamels is necessary to establish the suitability of an enamel for a proposed application. 1.1 This test method covers the measurement of the compressive stresses (Note 1) developed by fired porcelain enamels using the loaded-beam method. Note 18212;Although some may interpret the calculations that are used in this test method as indicating compressive load, it is commonly referred to as compressive stress within the porcelain enamel industry. 1.2 This test method is limited to the use of the loaded-beam method. However, this method includes charts (Fig. 1 and Fig. 2) that provide for conversion of loaded-beam test results to warp and ring stress values. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Compressive Stress of Porcelain Enamels by Loaded-Beam Method

JIS R 4301:1978 搪瓷制品质量标准

Quality standard of porcelain enamelled products

ASTM C614-74(2005) 工业瓷器用瓷漆的耐强碱腐蚀的标准试验方法

This test method is intended specifically for testing the resistance to alkaline attack of porcelain enamels to be used as a final finish on washing machines, dishwashers, combination washer-dryers, and similar appliances where the surface is normally exposed to an alkaline environment at elevated temperatures.1.1 This test method covers the measurement of the resistance of a porcelain enamel to a hot solution of tetrasodium pyrophosphate. Although the specific alkali mentioned herein is tetrasodium pyrophosphate the equipment and techniques are equally applicable to other alkali solutions.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Alkali Resistance of Porcelain Enamels

ISO 2747:1973 釉瓷和搪瓷.搪瓷烹调器具.耐热冲击性能的测定

Vitreous and porcelain enamels; Enamelled cooking utensils; Determination of resistance to thermal shock

ASTM C703-72(2006) 铝制搪瓷涂层的抗脱落试验方法

It is difficult to overemphasize the importance of the spall test. Porcelain enameled aluminum that fails this test will probably spall in service if subjected to moisture or weathering. 1.1 These test methods cover accelerated determination of the resistance of porcelain enamel coatings on aluminum alloys to spalling from exposure to moisture or weathering. Test Method A, using a 5 % solution of ammonium chloride, requires 96-h immersion while Test Method B, using a 1 % solution of antimony trichloride, is completed after 20 h of immersion. The spalling tendency is evaluated by the same criteria in both methods. While either method is suitable for magnesium silicon alloys, such as 6061, Test Method B is preferred for simple alloys or commercially pure aluminum, such as 1100.1.2 The test methods appear in the following order: SectionsTest Method A-Ammonium ChlorideTest Method B-Antimony Trichloride

Standard Test Methods for Spalling Resistance of Porcelain Enameled Aluminum

BS 3831:1964 家用器具和餐具搪瓷精加工规范

Requirements for the ground coat and cover coat of enamel, the enamel thickness, and imperfections that may or may not be acceptable. Definitions of imperfections appended. Applicable only to sheet steel or cast iron with the exception of baths.

Specification for vitreous enamel finishes for domestic and catering appliances

ASTM C375-58(2011)e1 搪瓷研磨用水的分类

Standard Classification of Water Used in Milling of Porcelain Enamel

ASTM C385-58(2009) 搪瓷器具抗热冲击性的标准试验方法

1.1 This test method covers the determination of the resistance of porcelain-enameled utensils to thermal shock. This test method is adaptable to any porcelain-enamel utensil that can be filled with water to a depth of 1 in. (25 mm). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Shock Resistance of Porcelain-Enameled Utensils

ASTM C375-58(2006) 搪瓷研磨用水的分类

1.1 This classification covers water used in the milling of porcelain enamel frit.

Standard Classification of Water Used in Milling of Porcelain Enamel

ASTM C385-58(2004)e1 搪瓷器具抗热冲击性的试验方法

1.1 This test method covers the determination of the resistance of porcelain-enameled utensils to thermal shock. This test method is adaptable to any porcelain-enamel utensil that can be filled with water to a depth of 1 in. (25 mm). This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Shock Resistance of Porcelain-Enameled Utensils

ASTM C385-58(2014) 搪瓷器具抗热冲击性的标准试验方法

1.1 This test method covers the determination of the resistance of porcelain-enameled utensils to thermal shock. This test method is adaptable to any porcelain-enamel utensil that can be filled with water to a depth of 1 in. (25 mm). 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Thermal Shock Resistance of Porcelain-Enameled Utensils

JIS A 5534:1979 搪瓷面砖

Porcelain enameled tiles