ASTM F3173/F3173M-23
飞机操纵特性标准规范

Standard Specification for Aircraft Handling Characteristics


ASTM F3173/F3173M-23 发布历史

ASTM F3173/F3173M-23由美国材料与试验协会 US-ASTM 发布于 2023-05-01。

ASTM F3173/F3173M-23在国际标准分类中归属于: 49.020 航空器和航天器综合。

ASTM F3173/F3173M-23 飞机操纵特性标准规范的最新版本是哪一版?

最新版本是 ASTM F3173/F3173M-23

ASTM F3173/F3173M-23 发布之时,引用了标准

* 在 ASTM F3173/F3173M-23 发布之后有更新,请注意新发布标准的变化。

ASTM F3173/F3173M-23的历代版本如下:

 

1.1 This specification addresses the airworthiness requirements for aeroplane handling characteristics in flight and on ground and water. 1.2 The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Normal Category aeroplanes; however, the content may be more broadly applicable, and should not be unduly limited. The topics covered within this specification are: Flight Characteristics, Controllability, Trim, Stability, Ground and Water Handling Characteristics, and Vibration, Buffet, and High-speed Characteristics. 1.3 An applicant intending to propose this information as Means of Compliance for a design approval must seek guidance from their respective oversight authority (for example, published guidance from applicable CAAs) concerning the acceptable use and application thereof. For information on which oversight authorities have accepted this specification (in whole or in part) as an acceptable Means of Compliance to their regulatory requirements (hereinafter “the Rules”), refer to the ASTM Committee F44 web page (www.astm.org/ COMMITTEE/F44.htm). Annex A1 maps the Means of Compliance of the ASTM standards to EASA CS-23, amendment 5, or later, and FAA 14 CFR Part 23, amendment 64, or later, rules. 1.4 Units—This specification may present information in either SI units, English Engineering units, or both; the values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F3173/F3173M-23

标准号
ASTM F3173/F3173M-23
发布
2023年
发布单位
美国材料与试验协会
当前最新
ASTM F3173/F3173M-23
 
 
引用标准
ASTM F3060 ASTM F3061/F3061M ASTM F3116/F3116M ASTM F3174/F3174M ASTM F3179/F3179M ASTM F3232/F3232M ASTM F3233/F3233M

ASTM F3173/F3173M-23相似标准


谁引用了ASTM F3173/F3173M-23 更多引用





Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号