SAE J2600-2002

Compressed Hydrogen Surface Vehicle Refuelling Connection Devices

被代替

SAE J2600-2002 发布历史

SAE J2600 applies to design, safety and operation verification of Compressed Hydrogen Surface Vehicle (CHSV) refuelling connection devices hereinafter referred to as nozzle and receptacle. CHSV Refuelling nozzles and receptacles shall consist of the following components, as applicable. Alternatives may be used as long as the alternative geometries shall not be interchangeable with the standard geometry specified in this SAE Standard and the standard geometry in Section 6 provides insufficient flow rates: a. Receptacle and protective cap (mounted on vehicle) (see Section 6 and 7); b. Nozzle (see Section 5). This document applies to devices which have Working Pressures of 25 MPa, 35 MPa, 50 MPa or 70 MPa hereinafter referred to in this document as the following (see 9.1c): H25 - 25 MPa at 15 鳦; H35 - 35 MPa at 15 鳦; H50 - 50 MPa at 15 鳦; H70 - 70 MPa at 15 鳦. This document applies to nozzles and receptacles which (1) prevent hydrogen fuelled vehicles from being refuelled by dispenser stations with Working Pressures higher than the vehicle; (2) allow hydrogen vehicles to be refuelled by dispenser stations with Working Pressures equal to or lower than the vehicle fuel system Working Pressure, (3) prevent hydrogen fuelled vehicles from being refuelled by other compressed gases dispensing stations and (4) prevent other gaseous fuelled vehicles from being refuelled by hydrogen dispensing stations. All dimensions used in this document are in metric units (International System of Units (SI)). For the purposes of this document, compressed hydrogen gas should meet the requirements of ISO 14687 Hydrogen fuel - Product specification. All references to pressures (MPa) throughout this document are to be considered gauge pressures unless otherwise specified. All test procedures listed in this document are design verification test procedures unless otherwise noted. All products must pass all tests to be considered to have met this design standard.

SAE J2600-2002由美国机动车工程师协会 US-SAE 发布于 2002，并于 2002-11-05 实施。

SAE J2600-2002 在中国标准分类中归属于: T13 进排气与燃油供给系统。

SAE J2600-2002的历代版本如下：

• 2015年 SAE J2600-2015 SAE J 2600-2015
• 2012年 SAE J2600-2012 压缩氢表面车辆加油连接装置
• 2002年 SAE J2600-2002

非常抱歉，我们暂时无法提供预览，您可以试试： 免费下载 SAE J2600-2002 前三页，或者稍后再访问。

注意： 点击下载后，生成下载文件时间比较长，请耐心等待......

标准号

SAE J2600-2002

发布

2002年

发布单位

美国机动车工程师协会

替代标准

SAE J2600-2012

当前最新

SAE J2600-2015

 

 

适用范围

SAE J2600 applies to design, safety and operation verification of Compressed Hydrogen Surface Vehicle (CHSV) refuelling connection devices hereinafter referred to as nozzle and receptacle. CHSV Refuelling nozzles and receptacles shall consist of the following components, as applicable. Alternatives may be used as long as the alternative geometries shall not be interchangeable with the standard geometry specified in this SAE Standard and the standard geometry in Section 6 provides insufficient flow rates: a. Receptacle and protective cap (mounted on vehicle) (see Section 6 and 7); b. Nozzle (see Section 5). This document applies to devices which have Working Pressures of 25 MPa, 35 MPa, 50 MPa or 70 MPa hereinafter referred to in this document as the following (see 9.1c): H25 - 25 MPa at 15 鳦; H35 - 35 MPa at 15 鳦; H50 - 50 MPa at 15 鳦; H70 - 70 MPa at 15 鳦. This document applies to nozzles and receptacles which (1) prevent hydrogen fuelled vehicles from being refuelled by dispenser stations with Working Pressures higher than the vehicle; (2) allow hydrogen vehicles to be refuelled by dispenser stations with Working Pressures equal to or lower than the vehicle fuel system Working Pressure, (3) prevent hydrogen fuelled vehicles from being refuelled by other compressed gases dispensing stations and (4) prevent other gaseous fuelled vehicles from being refuelled by hydrogen dispensing stations. All dimensions used in this document are in metric units (International System of Units (SI)). For the purposes of this document, compressed hydrogen gas should meet the requirements of ISO 14687 Hydrogen fuel - Product specification. All references to pressures (MPa) throughout this document are to be considered gauge pressures unless otherwise specified. All test procedures listed in this document are design verification test procedures unless otherwise noted. All products must pass all tests to be considered to have met this design standard.

SAE J2600-2002相似标准

谁引用了SAE J2600-2002 更多引用