ZH
RU
ES

Brazed three-point bending

Brazed three-point bending, Total:154 items.

In the international standard classification, Brazed three-point bending involves: Welding, brazing and soldering, Testing of metals, Materials for aerospace construction, Glass, Plastics, Pipeline components and pipelines, Farming and forestry, Reinforced plastics, Paper and board, Adhesives, Rubber and plastics products, Inorganic chemicals, Refractories, Products of the textile industry, Paints and varnishes, Medical equipment, Valves, Ceramics, Road vehicle systems, Insulating materials, Construction materials, Waxes, bituminous materials and other petroleum products, Products of the chemical industry.

RU-GOST R, Brazed three-point bending

GOST 24167-1980 Brazing and soldering joint. Bend testing method
GOST 34368.2-2017 Plastics. Method of determination of flexural creep by three-point loading

Association Francaise de Normalisation, Brazed three-point bending

NF A03-263:1983 Copper. Bending test for round tubes for capillary brazing and soldering.
NF T51-120-3:1995 Plastiques et composites - Détermination des propriétés de fatigue en flexion - - Partie 3 : essai en flexion trois points sur éprouvettes non encastrées.
NF Q03-127:2012 Paper and board - Determination of bending stiffness - General principles for two-point, three-point and four-point methods.
NF T30-010:1992 Paints and varnishes. Evaluation of adhesion or cohesion. Three point bending method.
NF EN ISO 899-2:2003 Plastiques - Détermination du comportement au fluage - Partie 2 : fluage en flexion par mise en charge en trois points
NF EN 1966:2009 Adhésifs structuraux - Caractérisation d'une surface par mesure de l'adhérence au moyen de la méthode de la flexion en trois points
NF T76-143*NF EN 1966:2009 Structural adhesives - Characterisation of a surface by measuring adhesion by means of the three point bending method.
NF T51-103-2/A1*NF EN ISO 899-2/A1:2015 Plastics - Determination of creep behaviour - Part 2 : flexural creep by three-point loading - Amendment 1
XP CEN/TS 15963:2014 Bitumes et liants bitumineux - Détermination de la température de résistance à la fissuration par un essai de flexion 3 points sur un barreau entaillé
NF EN ISO 899-2/A1:2015 Plastiques - Détermination du comportement au fluage - Partie 2 : fluage en flexion par mise en charge en trois points - Amendement 1
XP T66-078*XP CEN/TS 15963:2014 Bitumen and bituminous binders - Determination of the fracture toughness temperature by a three point bending test on a notched specimen

British Standards Institution (BSI), Brazed three-point bending

BS EN 2746:1998 Glass fibre reinforced plastics - Flexural test - Three point bend method
BS ISO 11093-7:2011 Paper and board. Testing of cores. Determination of flexural modulus by the three-point method
BS ISO 5628:2012 Paper and board. Determination of bending stiffness. General principles for two-point, three-point and four-point methods
BS EN 910:1996 Destructive tests on welds in metallic materials - Bend tests
BS EN ISO 899-2:2003+A1:2015 Plastics. Determination of creep behaviour. Flexural creep by three-point loading
BS ISO 11093-6:2005 Paper and board. Testing of cores - Determination of bending strength by the three-point method
DD ENV 1966-1996 Structural adhesives. Characterization of a surface by measuring adhesion by means of the three point bending method
BS 2782-10 Method 1005:1977 Methods of testing plastics. Glass reinforced plastics. Determination of flexural properties. Three point method
BS ISO 5628:2019 Tracked Changes. Paper and board. Determination of bending stiffness. General principles for two-point, three-point and four-point methods
BS ISO 23242:2020 Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for flexural strength of monolithic ceramic thin plates at room temperature by three-point or four-point bending
19/30375027 DC BS ISO 23242. Fine ceramics (advanced ceramics, advanced technical ceramics). Test method for flexural strength of monolithic ceramic thin plates at room temperature by three-point or four-point bending
23/30449747 DC BS EN ISO 899-2. Plastics. Determination of creep behaviour - Part 2. Flexural creep by three-point loading
BS EN 1966:2002 Structural adhesives - Characterisation of a surface by measuring adhesion by means of the three point bending method
BS EN 1966:2009 Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method
BS PD CEN/TS 15963:2014 Bitumen and bituminous binders. Determination of the fracture toughness temperature by a three point bending test on a notched specimen
BS DD CEN/TS 15963:2010 Bitumen and bituminous binders - Determination of the fracture toughness temperature by a three point bending test on a notched specimen

FI-SFS, Brazed three-point bending

SFS-ISO 6602 E:1986 This standard is approved in English

German Institute for Standardization, Brazed three-point bending

DIN EN 2746:1998-10 Aerospace series - Glass fibre reinforced plastics - Flexural test, three point bend method; German version EN 2746:1998
DIN 51902:1997 Testing of carbon materials - Determination of flexural strength by three point method - Solid matters
DIN EN ISO 5173:2012 Destructive tests on welds in metallic materials - Bend tests (ISO 5173:2009 + Amd 1:2011); German version EN ISO 5173:2010 + A1:2011
DIN EN 2746:1998 Aerospace series - Glass fibre reinforced plastics - Flexural test, three point bend method; German version EN 2746:1998
DIN 51902:2020 Testing of carbonaceous materials - Determination of flexural strength by three point method - Solid materials
DIN ISO 11093-6:2005-09 Paper and board - Testing of cores - Part 6: Determination of bending strength by the three-point method (ISO 11093-6:2005)
DIN 51902:2020-12 Testing of carbonaceous materials - Determination of flexural strength by three point method - Solid materials
DIN EN ISO 899-2:2003 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003); German version EN ISO 899-2:2003
DIN EN 12100:1997 Plastics piping systems - Polyethylene (PE) valves - Test method for the resistance to bending between supports; German version EN 12100:1997
DIN EN ISO 899-2:2015-06 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003 + Amd.1:2015); German version EN ISO 899-2:2003 + A1:2015 / Note: To be replaced by DIN EN ISO 899-2 (2023-03) (in preparation).
DIN EN 1966:2009-07 Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method; German version EN 1966:2009
DIN ISO 11093-7:2012-10 Paper and board - Testing of cores - Part 7: Determination of flexural modulus by the three-point method (ISO 11093-7:2011)
DIN EN ISO 899-2:2023-03 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO/DIS 899-2:2023); German and English version prEN ISO 899-2:2023 / Note: Date of issue 2023-02-03*Intended as replacement for DIN EN ISO 899-2 (2015-06).
DIN EN 1966:2009 Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method; English version of DIN EN 1966:2009-07

中华人民共和国国家质量监督检验检疫总局、中国国家标准化管理委员会, Brazed three-point bending

GB/T 34171-2017 Test method for flexural property of thin and ultrathin glass—Three-point bending method
GB/T 33099-2016 Test methods of stiffness for dipped reinforcing material—Three-point bending

Indonesia Standards, Brazed three-point bending

SNI 07-4076-1996 Method of free bend test for butt welded joint

American Society for Testing and Materials (ASTM), Brazed three-point bending

ASTM D5023-01 Standard Test Method for Measuring the Dynamic Mechanical Properties: In Flexure (Three-Point Bending)
ASTM D5023-07 Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending)
ASTM D5023-15 Standard Test Method for Plastics: Dynamic Mechanical Properties: In Flexure (Three-Point Bending)
ASTM D8058-19 Standard Test Method for Determining the Flexural Strength of a Geosynthetic Cementitious Composite Mat (GCCM) Using the Three-Point Bending Test
ASTM E2092-00 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM E2092-04 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM E2092-03 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM E2092-18 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM E2092-18a Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM D8058-23 Standard Test Method for Determining the Flexural Strength of a Geosynthetic Cementitious Composite Mat (GCCM) Using the Three-Point Bending Test
ASTM F2606-08 Standard Guide for Three-Point Bending of Balloon Expandable Vascular Stents and Stent Systems
ASTM E2092-13 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM F2606-08(2014) Standard Guide for Three-Point Bending of Balloon Expandable Vascular Stents and Stent Systems
ASTM F2606-08(2021) Standard Guide for Three-Point Bending of Balloon-Expandable Vascular Stents and Stent Systems
ASTM C78/C78M-10 Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
ASTM C78/C78M-10e1 Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
ASTM E2092-23 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM D5023-99 Standard Test Method for Measuring the Dynamic Mechanical Properties: In Flexure (Three-Point Bending)
ASTM C78/C78M-22 Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
ASTM C78/C78M-15 Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
ASTM E2092-09 Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis
ASTM C1609/C1609M-19 Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
ASTM C1609/C1609M-05 Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
ASTM C1609/C1609M-06 Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
ASTM C1609/C1609M-07 Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
ASTM C1609/C1609M-19a Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
ASTM C1609/C1609M-12 Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
ASTM C1609/C1609M-10 Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
ASTM C947-03 Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading)
ASTM C947-99 Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete (Using Simple Beam With Third-Point Loading)
ASTM D8458-22 Standard Test Method for Evaluation of Fatigue Performance of Asphalt Mixtures Using the Three-Point Bending Cylinder (3PBC) Test
ASTM D8058-17 Standard Test Method for Determining the Flexural Strength of a Geosynthetic Cementitious Composite Mat (GCCM) Using the Three-Point Bending Test
ASTM D8058-17e1 Standard Test Method for Determining the Flexural Strength of a Geosynthetic Cementitious Composite Mat (GCCM) Using the Three-Point Bending Test
ASTM E2769-13 Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading
ASTM E2769-15 Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading
ASTM E2769-16 Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading
ASTM D7972-14(2020) Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Three-Point Loading at Room Temperature
ASTM E2769-18 Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading

AENOR, Brazed three-point bending

UNE-EN 2746:1999 AEROSPACE SERIES. GLASS FIBRE REINFORCED PLASTICS. FLEXURAL TEST. THREE POINT BEND METHOD.
UNE-EN 1966:2009 Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method
UNE-EN ISO 899-2:2003 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003)

RO-ASRO, Brazed three-point bending

STAS 10897/3-1982 BRAZED JOINTS IMPACT BENDING TEST
STAS 10897/4-1983 Tests of metals MECHANICAL TESTING OF SOLDERED AND BRAZED JOINTS Bend testing
STAS 5540/8-1988 MECHANICAL TESTS OF FRICTION WELDED BUTT JOINTS Bending test

Society of Automotive Engineers (SAE), Brazed three-point bending

SAE J526-2010 Welded Low-Carbon Steel Tubing Suitable for Bending, Flaring, Beading, Forming and Brazing
SAE J526-2022 Welded Low-Carbon Steel Tubing Suitable for Bending, Flaring, Beading, Forming, and Brazing
SAE J949-2009 Test Method for Determining Stiffness of Interior Trim Materials and Substrates by a Three Point Bending Test
SAE J949-2022 Test Method for Determining Stiffness of Interior Trim Materials and Substrates by a Three-Point Bending Test

American National Standards Institute （ANSI), Brazed three-point bending

ANSI/ASAE S459-1993 Shear and Three-Point Bending Test of Animal Bones
ANSI/ASTM D5023:2001 Test Method for Measuring the Dynamic Mechanical Properties of Plastics Using Three Point Bending (08.03)

European Committee for Standardization (CEN), Brazed three-point bending

EN 2746:1998 Aerospace series - Glass fibre reinforced plastics - Flexural test - Three point bend method
EN 63:1977 Glass Reinforced Plastics: Determination of Flexural Properties; Three Point Method
EN 1966:2009 Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method
EN ISO 899-2:1996 Plastics - Determination of Creep Behaviour - Part 2: Flexural Creep by Three-Point Loading ISO 899-2: 1993
EN 12100:1997 Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports
EN ISO 5173:2023 Destructive tests on welds in metallic materials - Bend tests (Incorporates Amendment A1: 2011)
EN ISO 5173:2010 Destructive tests on welds in metallic materials - Bend tests (Incorporates Amendment A1: 2011)
EN ISO 899-2:2003 Plastics - Determination of Creep Behaviour - Part 2: Flexural Creep by Three-Point Loading ISO 899-2: 2003
prEN ISO 899-2 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO/DIS 899-2:2023)
EN ISO 899-2:2003/A1:2015 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading - Amendment 1 (ISO 899-2:2003/Amd 1:2015)
EN 1966:2002 Structural adhesives Characterisation of a surface by measuring adhesion by means of the three point bending method Supersedes ENV 1966: 1995
PD CEN/TS 15963:2014 Bitumen and bituminous binders - Determination of the fracture toughness temperature by a three point bending test on a notched specimen

Danish Standards Foundation, Brazed three-point bending

DS/EN 2746:1999 Aerospace series - Glass fibre reinforced plastics - Flexural test - Three point bend method
DS/EN 1966:2009 Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method
DS/EN ISO 899-2:2003 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading
DS/CEN/TS 15963:2010 Bitumen and bituminous binders - Determination of the fracture toughness temperature by a three point bending test on a notched specimen

Lithuanian Standards Office , Brazed three-point bending

LST EN 2746-2001 Aerospace series - Glass fibre reinforced plastics - Flexural test - Three point bend method
LST EN 1966-2009 Structural adhesives - Characterization of a surface by measuring adhesion by means of the three point bending method
LST EN ISO 899-2:2003 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003)

International Organization for Standardization (ISO), Brazed three-point bending

ISO 6602:1985 Plastics; Determination of flexural creep by three-point loading
ISO 5628:2019 Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods
ISO 5628:2012 Paper and board - Determination of bending stiffness - General principles for two-point, three-point and four-point methods
ISO/DIS 899-2:1968 Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading
ISO 23242:2020 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for flexural strength of monolithic ceramic thin plates at room temperature by three-point or four-point bending
ISO 899-2:2003/Amd 1:2015 Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading — Amendment 1

Professional Standard - Machinery, Brazed three-point bending

JB/T 7716-1995 Four-point bending fatigue test method for welded joints

AT-ON, Brazed three-point bending

ONORM EN 63-1979 Glass reinforced plastics. Determination of flexural properties. Three point method.
ONORM ENV 658-5-1993 Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 5: Determination of shear strength by short span bend test (three-point)

Korean Agency for Technology and Standards (KATS), Brazed three-point bending

KS M ISO 14679-2007(2017) Adhesives－Measurement of adhesion characteristics by a three－point bending method
KS M ISO 14679-2007(2022) Adhesives－Measurement of adhesion characteristics by a three－point bending method
KS M ISO 14679:2007 Adhesives－Measurement of adhesion characteristics by a three－point bending method
KS M ISO 899-2-2016(2021) Plastics－Determination of creep behavior－Part 2：Flexural creep by three-point loading
KS M ISO 11093-7:2020 Paper and board — Testing of cores — Part 7: Determination of flexural modulus by the three-point method
KS M ISO 11093-6:2022 Paper and board — Testing of cores — Part 6: Determination of bending strength by the three-point method
KS M ISO 11093-7:2014 Paper and board — Testing of cores — Part 7: Determination of flexural modulus by the three-point method
KS M ISO 11093-6:2016 Paper and board - Testing of cores - Part 6 : Determination of bending strength by the three-point method
KS M ISO 11093-7:2008 Paper and board-Testing of cores-Part 7:Determination of flexural modulus by the three-point method

ASD-STAN - Aerospace and Defence Industries Association of Europe - Standardization, Brazed three-point bending

PREN 2746-1990 Aerospace Series Glass Fibre Reinforced Plastics Determination of Flexural Properties Three Point Bend Method (Issue P 1)

国家市场监督管理总局、中国国家标准化管理委员会, Brazed three-point bending

GB/T 38978-2020 Refractory products—Determination of stress-strain (three-point bending method）

General Administration of Quality Supervision, Inspection and Quarantine of the People‘s Republic of China, Brazed three-point bending

GB/T 11546.2-2022 Plastics—Determination of creep behaviour—Part 2:Flexural creep by three-point loading
GB/T 22906.6-2008 Testing of cores.Part 6：Determination of bending strength by three-point method

Professional Standard - Medicine, Brazed three-point bending

YY/T 0858-2011 Standard guide for three-piont bending of balloon expandable vascular stents and stent systems

Malaysia Standards, Brazed three-point bending

MS 1473-1999 Method of test for measuring the dynamic mechanical properties of plastics using three point bending

KR-KS, Brazed three-point bending

KS M ISO 899-2-2016 Plastics－Determination of creep behavior－Part 2：Flexural creep by three-point loading
KS M ISO 11093-6-2016 Paper and board - Testing of cores - Part 6 : Determination of bending strength by the three-point method
KS M ISO 11093-7-2020 Paper and board — Testing of cores — Part 7: Determination of flexural modulus by the three-point method
KS M ISO 11093-6-2022 Paper and board — Testing of cores — Part 6: Determination of bending strength by the three-point method

CEN - European Committee for Standardization, Brazed three-point bending

DD ENV 1966-1995 Structural Adhesives - Characterization of a Surface by a Measuring Adhesion by Means of the Three Point Bending Method

未注明发布机构, Brazed three-point bending

DIN EN 1966:2003 Structural adhesives — Characterization of a surface by measuring adhesion by means of the three point bending method
BS PD CEN TS 15963:2014 Bitumen and bituminous binders — Determination of the fracture toughness temperature by a three point bending test on a notched specimen

TH-TISI, Brazed three-point bending

TIS 2246.2-2005 Plastics.determination of creep behaviour.part 2: flexural creep by three.point loading

European Association of Aerospace Industries, Brazed three-point bending

AECMA PREN 2746-1990 Aerospace Series Glass Fibre Reinforced Plastics Determination of Flexural Properties Three Point Bend Method Issue P 1

The American Road & Transportation Builders Association, Brazed three-point bending

AASHTO T 97-2014 Standard Method of Test for Flexural Strength of Concrete (Using Simple Beam with Third- Point Loading)

AASHTO - American Association of State Highway and Transportation Officials, Brazed three-point bending

T 97-2017 Standard Method of Test for Flexural Strength of Concrete (Using Simple Beam with Third- Point Loading)
T 97-2014 Standard Method of Test for Flexural Strength of Concrete (Using Simple Beam with Third- Point Loading)

Aerospace, Security and Defence Industries Association of Europe (ASD), Brazed three-point bending

ASD-STAN PREN 2746-1990 Aerospace Series Glass Fibre Reinforced Plastics Determination of Flexural Properties Three Point Bend Method (Issue P 1)

Japanese Industrial Standards Committee (JISC), Brazed three-point bending

JIS K 7084:1993 Testing method for impact properties of carbon fibre reinforced plastics by instrumented 3-point bending impact test