13.220.99 有关消防的其他标准 标准查询与下载

NF S62-301-7*NF EN 12101-7:2011 烟热控制系统.第7部分:排烟管段.

Smoke and heat control systems - Part 7 : Smoke duct sections.

DIN EN 12101-7:2011 烟和热控制系统.第7部分:烟道型材;德文版本EN 12101-7-2011

This European Standard applies to smoke duct sections, placed on the market and intended to operate as part of a pressure differential system or smoke and heat exhaust system. This standard specifies requirements and gives reference to the test methods defined for smoke duct sections and their associated components, which are intended to be installed in such systems in buildings. It also provides for the evaluation of conformity of the products to the requirements of this standard. Furthermore, marking and information on installation and maintenance of these products are also given in this European Standard.

Smoke and heat control systems - Part 7: Smoke duct sections; German version EN 12101-7:2011

DIN EN 12101-8:2011 烟和热控制系统.第8部分:排烟阀;德文版本EN 12101-8-2011

This European Standard applies to smoke control dampers, placed on the market and intended to operate as part of a pressure differential system or smoke and heat exhaust system. This standard specifies requirements and gives reference to the test methods defined for smoke control dampers and their associated components, such as actuators which are intended to be installed in such systems in buildings. It also provides for the evaluation of conformity of the these products to the requirements of this standard. Furthermore, provision on marking and information on installation and maintenance of these products are also given.

Smoke and heat control systems - Part 8: Smoke control dampers; German version EN 12101-8:2011

BS DD ISO/TS 24679:2011 防火安全工程.防火结构性能

Fire safety engineering. Performance of structures in fire

BS EN 12101-8:2011 烟和热控制系统.排烟控制阀

This European Standard applies to smoke control dampers, placed on the market and intended to operate as part of a pressure differential system or smoke and heat control system. This standard specifies requirements and gives reference to the test methods defined for smoke control dampers and their associated components, such as actuators which are intended to be installed in such systems in buildings. It also provides for the evaluation of conformity of these products to the requirements of this standard. Furthermore, provision on marking and information on installation and maintenance of these products are also given. This European Standard distinguish between two categories of smoke control dampers, i.e. single compartment smoke control dampers and multi-compartment fire resisting smoke control dampers. Smoke control dampers covered by this European Standard can be installed into smoke control system ducts or onto the ducts´ surface. They can be installed also into a wall, floor or ceiling/roof elements or onto the surface of these elements. To avoid duplication, reference is made to a variety of other standards. To this end, this standard is to be read in conjunction with EN 13501-4, EN 1366-10 and EN 1366-2, for details of the furnace testing. This standard does not consider in detail the detrimental and/or corrosive effects that may be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently.

Smoke and heat control systems. Smoke control dampers

BS EN 12101-7:2011 烟和热控制系统.烟道截面

This European Standard applies to smoke control duct sections, placed on the market and intended to operate as part of a pressure differential system or smoke and heat exhaust system. This standard specifies requirements and gives reference to the test methods defined for smoke control duct sections and their associated components (for example, hangers and other items proven at the time of testing), which are intended to be installed in such systems in buildings. It also provides for the evaluation of conformity of the products to the requirements of this standard. Furthermore, marking and information on installation and maintenance of these products are also given in this European Standard. To avoid duplication, reference is made to a variety of other standards. To this end, this standard is to be read in conjunction with EN 1366-8, EN 1366-9 and EN 1366-1, for details of the fire resistance testing and EN 13501-4 for corresponding classification. This standard has not considered in detail the detrimental and/or corrosive effects that may be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently. This European Standard also governs associated components used together with smoke control duct sections such as turning vanes and silencers, with the exception of natural and powered smoke ventilators and smoke control dampers, which are covered by separate standards. Ducts for use other than in smoke and heat exhaust/control systems are not covered by this standard.

Smoke and heat control systems. Smoke duct sections

EN 12101-8:2011 烟雾和热量控制系统-第8部分:排烟控制阻尼器

This European Standard applies to smoke control dampers, placed on the market and intended to operate as part of a pressure differential system or smoke and heat control system.This standard specifies requirements and gives reference to the test methods defined for smoke control dampers and their associated components, such as actuators which are intended to be installed in such systems in buildings. It also provides for the evaluation of conformity of these products to the requirements of this standard. Furthermore, provision on marking and information on installation and maintenance of these products are also given.This European Standard distinguish between two categories of smoke control dampers, i.e. single compartment smoke control dampers and multi-compartment fire resisting smoke control dampers. Smoke control dampers covered byThis European Standard can be installed into smoke control system ducts or onto the ducts′ surface. They can be installed also into a wall, floor or ceiling/roof elements or onto the surface of these elements. To avoid duplication, reference is made to a variety of other standards. ToThis end,This standard is to be read in conjunction with EN 13501-4, EN 1366-10 and EN 1366-2, for details of the furnace testing.This standard does not consider in detail the detrimental and/or corrosive effects that may be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently.

Smoke and heat control systems - Part 8: Smoke control dampers

EN 12101-7:2011 烟雾和热量控制系统-第7部分:烟管部分

This European Standard applies to smoke control duct sections, placed on the market and intended to operate as part of a pressure differential system or smoke and heat exhaust system.This standard specifies requirements and gives reference to the test methods defined for smoke control duct sections and their associated components (for example, hangers and other items proven at the time of testing), which are intended to be installed in such systems in buildings. It also provides for the evaluation of conformity of the products to the requirements of this standard. Furthermore, marking and information on installation and maintenance of these products are also given inThis European Standard. To avoid duplication, reference is made to a variety of other standards. ToThis end,This standard is to be read in conjunction with EN 1366-8, EN 1366-9 and EN 1366-1, for details of the fire resistance testing and EN 13501-4 for corresponding classification.This standard has not considered in detail the detrimental and/or corrosive effects that may be caused by process chemicals present in the atmosphere, which are drawn through the system intentionally or inadvertently.This European Standard also governs associated components used together with smoke control duct sections such as turning vanes and silencers, with the exception of natural and powered smoke ventilators and smoke control dampers, which are covered by separate standards. Ducts for use other than in smoke and heat exhaust/control systems are not covered byThis standard.

Smoke and heat control systems - Part 7: Smoke duct sections

BS ISO 27368:2008 分析血液中的窒息毒物 一氧化碳和氰化氢

1   Scope This International Standard details analytical methods suitable for analysing the two primary toxic combustion gases, carbon monoxide (CO) and hydrogen cyanide (HCN), in blood samples collected from fire casualties. In blood, CO is measured as carboxyhaemoglobin (COHb) and HCN as cyanide ion (CN − ). Although numerous methods are reported in the literature for performing blood COHb and CN − analyses, the analytical methods included herein are based upon their suitability for performing the analysis on ante-mortem and post-mortem blood samples from fire casualties. The analytical principle, analysis time, repeatability, reproducibility, robustness, effectiveness and instruments used are considered for those methods. Some of the methods described herein might not be suitable for analysing putrid or clotted blood. Burned (solid) blood can be analysed after homogenization.

Analysis of blood for asphyxiant toxicants. Carbon monoxide and hydrogen cyanide

BS ISO 27368:2011 窒息性毒物的血液分析.一氧化碳和氰化氢

Analysis of blood for asphyxiant toxicants. Carbon monoxide and hydrogen cyanide

ANSI/NFPA 276-2011 带可燃性露天平台上方屋顶元件的屋顶装配模块放热率的测定用点火试验标准方法

1.1 Scope 1.1.1 This standard determining the heat release rate of combustible building assemblies or combustible above-deck roofing components when exposed to an internal fire. 1.1.2 The performance of the above deck roofing assembly is evaluated by determining the heat release of the test specimen when compared to a noncombustible test specimen.

Standard Method of Fire Tests for Determining the Heat Release Rate of Roofing Assemblies with Combustible Above-Deck Roofing Components

ANSI/NFPA 160-2011 受众前火焰效果应用标准

This standard shall provide requirements for the protection of property, operators, performers, support personnel, and the viewing audiences where flame effects are used indoors or outdoors. The purpose of this standard shall be to provide minimum requirements to the operators and manufacturers for the safe operation of flame effects. 1.1.1* This standard shall apply to flame effects for entertainment, exhibition, demonstration, or simulation before an audience, including their design, fabrication, installation, testing, control, operation, and maintenance. 1.1.2 This standard shall apply to the following: (1) Use of indoor and outdoor flame effects before an audience (see 1.4.8, Flame Effect) (2) Design, fabrication, installation, testing, control, operation, and maintenance of equipment, materials, procedures, and systems used to produce flame effects (3) Rehearsal, videotaping, audiotaping, or filming of any television, radio, or movie production if such production is before an audience and includes the use of flame effects (4) Rehearsal of any production incorporating flame effects before an audience. 1.1.3 This standard shall not apply to the following: (1) Flame effects produced solely by pyrotechnic special effects devices (2)* Use of pyrotechnic special effects (3)* Storage of flammable solids, liquids, and gases (4) Manufacture, off-site storage, and transportation of materials and equipment used to produce flame effects (5) Use of flame effects in fire training Exception: Where there is an audience that is not part of the training, this standard shall apply. (6)* Manufacture, transportation, storage, sale, or use of model or high-power rocket motors (7) Traditional nontheatrical public display of flames such as the following: a. Use of lighted candles in restaurants or religious services b. Fireplaces in areas open to the public c. Restaurant cooking visible to the patrons d. Listed Group II flame effects (8) Use of consumer fireworks by the public (9) Use of motor vehicles in races or sanctioned competitive sporting events.

Standard for the Use of Flame Effects Before an Audience

ANSI/NFPA 34-2011 易燃或可燃液体的浸渍和涂膜处理标准

1.1 Scope. 1.1.1 This standard shall apply to processes in which articles or materials are passed through tanks, vats, containers, or process equipment that contain flammable or combustible liquids, including but not limited to dipping, roll coating, flow coating, curtain coating, and cleaning. 1.1.2 This standard shall also apply to dipping and coating processes that use water-borne, water-based, and water-reducible materials that contain flammable or combustible liquids or that produce combustible deposits or residues.

Standard for Dipping and Coating Processes Using Flammable or Combustible Liquids

DB52/T 695-2010 农村消防安全管理规程

Rural Fire Safety Management Regulations

DB52/T 698-2010 仓储物流单位消防安全管理规程

Fire safety management regulations for warehousing and logistics units

DB52/T 694-2010 社会单位消防安全管理规程

Regulations on Fire Safety Management of Social Units

DB52/T 699-2010 易燃易爆场所消防安全管理规程

Fire Safety Management Regulations for Inflammable and Explosive Places

DB52/T 696-2010 社区消防安全管理规程

Community Fire Safety Management Regulations

DIN 18230-1:2010 工业建筑中的结构防火.第1部分:分析必需的抗燃烧时间

Structural fire protection in industrial buildings - Part 1: Analytically required fire resistance time

DS/ISO 16312-1:2010 评估物理火灾模型有效性的指南，以获取用于火灾危害和风险评估的火灾排放物毒性数据 第1部分：标准

This part of ISO 16312 provides technical criteria and guidance for evaluating physical fire models (i.e.laboratory combustion devices and operating protocols) used in effluent toxicity studies for obtaining data on the effluent from products and materials under fire conditions relevant to life safety[2]. Relevant analytical methods, calculation methods, bioassay procedures and prediction of the toxic effects of fire effluents can be referenced in ISO 19701[3], ISO 19702[4], ISO 19703[5], ISO 19706[6], ISO 13344[7], and ISO 13571.

Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment - Part 1: Criteria