13.340.20 头部防护设备 标准查询与下载

GB 6095-1985 安全带

本标准适用于围杆、悬挂、攀登等高处作业用安全带。不适用于消防和吊物用安全带。

Safety belts

GB/T 3609.2-1983 焊接护目镜和面罩非光学测试方法

本标准适用于焊接护目镜和面罩的非光学测试。

Methods of non-optical test for welding goggles and mask

GB/T 3609.3-1983 焊接护目镜光学性能试验方法

本标准适用于焊接护目镜的光学性能测试。

Methods of optical test for welding goggles

BS EN 13819-1:2020+A1:2024

Hearing protectors. Testing - Physical test methods

BS EN 352-2:2020+A1:2024

Hearing protectors. General requirements - Earplugs

ASTM E3368/E3368M-24 美国公共安全官员佩戴的防弹头盔的标准规范

1.1  This specification specifies minimum performance requirements and test methods for the ballistic resistance of helmets used by U.S. public safety officers and intended to protect the head against handgun and rifle ammunition. 1.1.1  The test methods within this specification were developed and validated for broadly available helmet designs. Some helmet designs may require additional or different testing than that specified in this specification. 1.2  This specification addresses ballistic performance in terms of: 1.2.1  Helmet resistance to penetration (RTP) of shell, fasteners, and weak points; 1.2.2  Helmet shell ballistic limit (V50); and 1.2.3  Face shield RTP and deformation. 1.3  Helmets covered by this specification are classified into RTP ballistic protection levels (see Section 8 ). 1.4  This specification addresses non-ballistic performance in terms of: 1.4.1  Helmet impact attenuation; 1.4.2  Helmet shell compression resistance; 1.4.3  Face shield resistance to blunt impact, deflection, and projectile impact; 1.4.4  Face shield optics; and 1.4.5  Retention system strength. 1.5  Backface deformation (BFD) measurement is not addressed as a requirement for compliance with this specification. If the user of this specification is interested in BFD measurement, see Appendix X1 . 1.6  Armor appliques are not addressed within this version of the specification. 1.7  This specification is applicable for compliance testing, verification testing, certification testing, or research and development testing. 1.8  This specification is divided into the following sections: Section Title 1 Scope 2 Referenced Documents 3 Terminology 4 Significance and Use 5 Test Threats, Equipment, and Materials 6 Test Item Requirements 7 Procedure for Visual Examination 8 Helmet Resistance to Penetration (RTP) Ballistic Protection Levels and Test Threats 9 Ballistic Performance Requirements for Helmet Shell RTP and BFD 10 Ballistic Performance Requirements for Face Shields 11 Ballistic Performance Requirements for Helmet Shell Ballistic Limit (V50) 12 Ballistic Performance Requirements for Fasteners 13 Ballistic Performance Requirements for Weak Points 14 Non-ballistic Performance Requirements for Helmets and Face Shields 15 Product Documentation Requirements 16 Product Label and Package Label Requirements 17 Test Report 18 Keywords Annex A1 ASTM Helmet RTP Ballistic Protection Levels and Associated Test Threats Annex A2 Ballistic Testing Summary Annex A3 Non-ballistic Testing Summary Appendix X1 Optional Backface Deformation Measurement Acceptance Criteria and Test Procedure 1.9  Units— The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.10  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ballistic-Resistant Helmets Worn by U.S. Public Safety Officers

ASTM E3299/E3299M-24 头盔抗压性的标准试验方法

Standard Test Methods for Compression Resistance of Helmets

BS EN 352-9:2020+A1:2024 听力保护器 安全要求 具有安全相关音频输入的耳塞

Hearing protectors. Safety requirements - Earplugs with safety-related audio input

BS EN 352-10:2020+A1:2024 听力保护器 安全要求 娱乐音频耳塞

Hearing protectors. Safety requirements - Entertainment audio earplugs

BS EN 352-6:2020+A1:2024 听力保护器 安全要求 具有安全相关音频输入的耳罩

Hearing protectors. Safety requirements - Earmuffs with safety-related audio input

BS EN 13819-3:2019+A1:2024 听力保护器 测试 补充声学测试方法

Hearing protectors. Testing - Supplementary acoustic test methods

BS EN 352-8:2020+A1:2024 听力保护器 安全要求娱乐音响耳罩

Hearing protectors. Safety requirements - Entertainment audio earmuffs

GSO ISO 21924-4:2024 武术防护装备 第4部分：头部保护器的附加要求和试验方法

ISO 21924-4:2017 specifies additional requirements and test methods for head protectors without face protection used in unarmed martial arts, such as taekwondo, karate, kick-boxing and similar disciplines. ISO 21924-4:2017 also applies to head protectors used in boxing.

Protective equipment for martial arts — Part 4: Additional requirements and test methods for head protectors

24/30461087 DC 工业防护头盔

Industrial protective helmets

24/30433506 DC BS EN 13911 消防员防护服 消防员防火头罩的要求和测试方法

BS EN 13911 Protective clothing for firefighters - Requirements and test methods for fire hoods for firefighters

BS EN ISO 12311:2023 个人保护设备 太阳镜及相关眼镜的测试方法

Personal protective equipment. Test methods for sunglasses and related eyewear

ASTM F2439-17(2023) 足球用头盔标准规范

Standard Specification for Headgear Used in Soccer

ASTM F1849-23 冰上速度滑冰（长道）和短道速度滑冰（不包括曲棍球）用头盔的标准规范

Standard Specification for Helmets Used in Ice Speed Skating (Long Track) and Short Track Speed Ice Skating (Not to Include Hockey)

ASTM F2178/F2178M-23a 电弧额定眼睛或面部防护产品的标准规范

Standard Specification for Arc Rated Eye or Face Protective Products

ISO 18527-3:2020/AWI Amd 1:2023 运动用眼面部防护 第 3 部分：用于水面游泳的眼镜的要求和测试方法 修正案 1

Eye and face protection for sports use — Part 3: Requirements and test methods for eyewear intended to be used for surface swimming — Amendment 1