13.340.20 头部防护设备 标准查询与下载

ASTM F1952-22 下坡山地自行车赛用头盔的标准规范

1.1 This specification covers performance requirements for helmets used by downhill mountain bicycle riders. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; hence, this specification requires greater impact protection and provides performance criteria for chin bars on full-face helmets, but does not require full-face helmets. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance specification and is not intended to restrict design. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification that the product meets all of the requirements of this specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets parts of this standard. 1.4 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 This standard is subject to revision at any time by ASTM. It must be reviewed every five years and if not revised either reapproved or withdrawn. References to the standard must include the version date. No references to a version that has been replaced or withdrawn shall be placed on any product or its packaging manufactured more than 24 months after the effective revision or withdrawal date. Go to astm.org to verify the latest version of this standard. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Helmets Used for Downhill Mountain Bicycle Racing

ASTM F2032-22 BMX自行车用头盔的标准规范

1.1 This specification covers performance requirements for helmets used in BMX cycling. Studies have shown higher risk to the head and face for this sport as compared to recreational street riding; therefore, this specification requires impact protection over a larger area of the head than Specification F1447 and the CPSC standard. This specification also provides performance criteria for helmets equipped with chin bars. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446 except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear with faceguard meets all of the requirements of the specification in their entirety. A headgear with faceguard that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification. 1.4 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 This standard is subject to revision at any time by ASTM. It must be reviewed every five years and if not revised either reapproved or withdrawn. References to the standard must include the version date. No references to a version that has been replaced or withdrawn shall be placed on any product or its packaging manufactured more than 24 months after the effective revision or withdrawal date. Go to astm.org to verify the latest version of this standard. 1.6 The values stated in SI units are to be regarded as standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Helmets Used for BMX Cycling

ISO 12312-1:2022 眼睛和面部防护.太阳镜和相关眼镜.第1部分:通用太阳镜

This document is applicable to all afocal (plano power) sunglasses and clip-ons for general use, including road use and driving, intended for protection against solar radiation. Information on the use of sunglass filters is given in Annex A. Requirements for unmounted filters used as replacement or alternative filters are given in Annex C. This document is not applicable to: a) eyewear for protection against radiation from artificial light sources; b) eye protectors intended for specific sports (e.g. ski goggles or other types – see ISO 18527 (all parts)); c) sunglasses that have been medically prescribed for attenuating solar radiation; d) products intended for direct observation of the sun, such as for viewing a partial or annular solar eclipse, for which ISO 12312-2 applies; e) products intended for occupational eye protection – see, for example, ISO 16321 (all parts).

Eye and face protection — Sunglasses and related eyewear — Part 1: Sunglasses for general use

EN ISO 18527-1:2022 运动用眼睛和面部防护.第1部分：下坡滑雪和单板滑雪护目镜的要求

This document applies to all goggles with plano lenses, intended for eye protection against hazards including ultraviolet and visible solar radiation, rain, snow and wind, during downhill skiing, snowboarding and other similar activities. This document applies to downhill skiing and snowboarding goggles fitted with an insert to carry prescription lenses. It specifies requirements and testing for materials, performance, marking of goggles and information to be supplied by the manufacturer. Information on the selection and use of downhill skiing and snowboarding goggles is given in Annex A. This document does not apply to a) eye protectors for protection when operating or travelling on a motorized vehicle, b) eye protectors for protection against optical radiation from artificial sources, such as those used in solaria, c) eye protectors for direct observation of the sun, and d) eye protectors intended for sports with unrelated hazards and risks.

Eye and face protection for sports use - Part 1: Requirements for downhill skiing and snowboarding goggles (ISO 18527-1:2021)

ISO 12312-3:2022 眼睛和面部保护.太阳镜和相关眼镜.第3部分:跑步、骑自行车和类似活动生活方式用太阳镜

This document is applicable to all nominally afocal (plano power) sunglasses for protection agains t environmental elements, such as solar radiation, wind, dus t and rain when running, cycling and following similar active lifestyle recreational activities but not intended for competitive sporting activities where enhanced impact resis tance is required. The document specifies additional material, design, performance and marking requirements. The other applicable requirements are given in ISO 12312-1 . This type of sunglass is designed to reduce secondary hazards to the wearer in an accident rather than to provide high amounts of impact protection which may be difficult in a spectacle format. This document is not applicable to: a) eyewear for protection against radiation from artificial light sources, such as those used in solaria; b) eye protectors intended for specific sports, e. g. ski goggles or other types – see ISO 18527 (all parts) ; c) eye protectors for sports that include the use of a ball, s tick, bat, racquet or other implement; d) sunglasses that have been medically prescribed for attenuating solar radiation; e) products intended for direct observation of the sun, such as for viewing a partial or annular solar eclipse, for which ISO 12312-2 applies; f) products intended for occupational eye protection – for example, see ISO 16321 (all parts) .

Eye and face protection — Sunglasses and related eyewear — Part 3: Sunglasses for running, cycling and similar active lifestyles

GSO ISO 4869-6:2022 声学 听力保护器 第6部分：主动降噪耳罩声音衰减的测定

This document is concerned with active noise reduction (ANR) earmuffs. It specifies the test methods for the determination of the active insertion loss and calculation procedures for deriving the total attenuation. For this aim, the values of sound attenuation in the passive mode also have to be known and are determined according to ISO 4869‑1. These methods are intended for steady noise exposures and are not applicable to noises containing impulsive components. The test methods account for the acoustical interaction between the wearer and the device using measurements of passive (REAT) and active microphone-in-real-ear (MIRE) measurements as specified in ISO 4869‑1 and ISO 11904‑1, respectively.

Acoustics — Hearing protectors — Part 6: Determination of sound attenuation of active noise reduction earmuffs

GSO ECE 22:2022 关于批准摩托车和轻便摩托车驾驶员和乘客防护头盔及其护目镜的统一规定

This Regulation applies to protective helmets for drivers and passengers of mopeds and of motor cycles with or without side-car 1/ and to the visors fitted to such helmets or intended to be added to them.

Uniform provisions concerning the approval of protective helmets and their visors for drivers and passengers of motor cycles and mopeds

GSO EN 166:2022 个人眼睛防护 规格

This European standard specifies functional requirements for various types of personal eye-protectors. The transmittance requirements for various types of filter oculars are given in separate standards (see clause 3).

Personal eye-protection - Specifications

ASTM F2178/F2178M-22 电弧防护眼睛或面部产品的标准规范

1.1 This product specification is used to determine the arc rating and specify the requirements for products intended for use as eye or face protection for workers exposed to electric arcs. The arc rating is determined in the test with an arc which has a heat flux value of 2100 kW/m2 [50 cal/cm2 /s]. Products are tested as sold. 1.2 The products covered by this standard are in the form of faceshields attached to the head by protective helmets (hard hats), headgear, hood assemblies, safety spectacles or goggles. Faceshields, safety spectacles or goggles are tested with or without other face and head protective products, for example, sock hoods, balaclavas, sweat shirt hoods or jacket hoods. 1.2.1 Fabric layers used in the design of face protection products such as in hood, neck guards, balaclava, meet the requirements of Specification F1506. When fabrics are designed into the protection provided for eye or face protective products, the arc rating of fabric system is first determined by Test Method F1959/F1959M. 1.2.2 The arc rating of the eye or face protective product which requires fabric to provide protection to the face or head will not be higher than the lower arc rating of either the fabric system or the shield/visor assembly. 1.3 The values stated in SI units shall be regarded as standard except as noted. Within the text, alternate units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, alternate systems must be used independently of the other. Combining values from the systems described in the text may result in nonconformance with the method. 1.4 This standard does not purport to describe or appraise the effect of the electric arc fragmentation or propulsion of parts of equipment or molten metal splatter, deposited from the pressure wave containing molten metals and possible fragments of other materials except to the extent that heat energy transmission due to these arc explosion phenomena is reduced by test specimens. 1.5 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 11. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Arc Rated Eye or Face Protective Products

ASTM F2879-22 Airsoft运动用眼睛保护装置的标准规范

1.1 This specification applies to eye protective devices (EPDs) designed for use by participants in the sport of airsoft with 6-mm airsoft projectiles. These EPDs are designed to minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration of airsoft projectiles. 1.2 When airsoft guns are used for target practice with a paper or gel target and a backstop sufficient to prevent ricochet, shooters may wear eye protection (shooting glasses) appropriate for use with firearms, ball bullet (BB) guns or air guns that meet ANSI Z87.1. The balance of this specification applies to EPDs designed for use by participants in tactical sports using airsoft guns. 1.3 EPDs meeting the requirements of this specification offer protection to the eyes and adnexa and not necessarily to any other parts of the head. 1.4 This specification does not limit the wearing of eyeglasses or contact lenses when used in conjunction with the EPD based on the information provided by the manufacturer in 9.2.21. 1.5 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.6 The following information is provided for the laboratory conducting the test for the protection of their personnel: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Eye Protective Devices for Airsoft Sports

ASTM F1776-22 彩弹运动用眼睛保护装置的标准规范

1.1 This specification applies to eye, face, and head protective devices, designed for use by players of the sport of paintball, which minimize or significantly reduce injury to the eye, adnexa of eye, face, and head due to paintball impact or penetration, or both. 1.2 EHPDs by nature provide three types of protection. The first type of protection is for the eyes and adnexa of eye and not necessarily for any other parts of the face or head. The second type of protection adds coverage for the ears and face. The third type of coverage adds cranial coverage in addition to that provided to types II and III. These coverage types are defined in Section 8. 1.3 This specification does not limit the wearing of eyeglasses or contact lenses when used in conjunction with the EHPD. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Eye Protective Devices for Paintball Sports

ASTM F3165-16(2022) 曲棍球守门员用喉部防护设备的标准规范

1.1 This specification covers performance requirements and test methods for throat protectors marketed, sold, and intended for ice hockey goalkeepers. 1.2 The intent of this specification is to reduce the risk of injury to the throat without compromising the form or appeal of the game. To do so, the protector shall be used: 1.2.1 As intended within the rules of the game and 1.2.2 In accordance with the manufacturer’s instructions. 1.3 Ice hockey is a sport with intrinsic hazards associated with the normal conduct of the game. Participation in ice hockey implies the acceptance of some risk of injury. Use of a throat protector certified to this specification will not prevent all injuries. 1.4 This specification has been prepared after careful consideration of the frequency and mechanisms associated with throat injuries that can potentially occur within the rules of the game of ice hockey. 1.5 Requirements and the corresponding test methods, where appropriate, are given for the following: 1.5.1 Construction, 1.5.2 Puck impact resistance, 1.5.3 Coverage, 1.5.4 Marking and information. 1.6 Throat protection is intended for use by goalkeepers. 1.7 Use of the singular does not exclude the plural (and vice versa) when the sense allows. 1.8 Although the intended primary application of this specification is stated in this scope, note that it remains the responsibility of the users of this specification to judge its suitability for their particular purpose. 1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Throat Protective Equipment for Hockey Goaltenders

BS EN ISO 19818-1:2021 眼睛和面部保护 激光辐射防护 要求和测试方法

Eye and face protection. Protection against laser radiation - Requirements and test methods

EN ISO 16321-1:2022 职业用眼睛和面部防护.第1部分：一般要求

This document specifies general requirements for eye and face protectors. These protectors are intended to provide protection for the eyes and faces of persons against one or more common occupational hazards such as impacts from flying particles and fragments, optical radiation, dusts, splashing liquids, molten metals, heat, flame, hot solids, harmful gases, vapours and aerosols. Additional requirements for eye and face protectors used during welding and related techniques and for mesh protectors are given in ISO 16321-2 and ISO 16321-3, respectively. This document applies to: — all plano as well as corrective and prescription lensed protectors and components; — those eye and face protectors used for occupational-type tasks that are performed similarly to an occupation, e.g. "do-it-yourself"; — those eye and face protectors used in educational establishments. This document does not apply to: — protectors specifically intended for protection against only solar radiation and used in non- occupational environments for which the ISO 12312 series applies; — protectors for medically prescribed applications (not occupational), e.g. eye protection for severe dry eye, tints prescribed for medical conditions; — patient eye protectors during diagnosis or treatment (e.g. ISO/TR 22463); — protectors for use during medical or e.g. aesthetic applications, e.g. intense light sources (ILS) for which the ISO 12609 series applies; — protectors specifically intended for sports for which the ISO 18527 series applies; — laser protectors; — face protectors intended for live-working to protect against short-circuit electric arcs for which IEC 62819 applies; — protectors intended to protect against ionizing radiation, e.g. X-rays, for which IEC 61331-3 applies.

Eye and face protection for occupational use - Part 1: General requirements (ISO 16321-1:2021)

EN ISO 16321-3:2022 职业用眼睛和面部防护装置.第3部分：网状防护装置的附加要求

This document specifies additional performance and marking requirements for mesh protectors designed to provide protection for the eyes and faces of persons against mechanical hazards such as impacts from flying particles and fragments. The other applicable requirements for mesh protectors and the frames/mountings to which they are intended to be fitted are given in ISO 16321‑1. This document also applies to mesh protectors used in educational establishments. This document also applies to those eye and face protectors used for occupational-type tasks that are performed similarly to an occupation, e.g. "do‑it‑yourself". This document is not applicable to protectors for use against liquid splash (including molten metal), hot solid risks, infrared and ultraviolet radiation. For protection against these hazards suitable additional or alternative protectors according ISO 16321‑1 will be needed. This document does not apply to mesh protectors used in sports such as fencing.

Eye and face protection for occupational use - Part 3: Additional requirements for mesh protectors (ISO 16321-3:2021)

ASTM E3299/E3299M-22 头盔抗压性的标准试验方法

1.1 This standard provides test methods for assessing compression resistance of helmets worn by military, law enforcement, and corrections personnel. These test methods are applicable for many styles of helmet (that is, high-cut, mid-cut, full-cut). 1.2 Three compression test methods are included: (1) topto-bottom, (2) side-to-side, and (3) front-to-back. 1.3 It is anticipated that this standard will be referenced by suppliers, certifiers, purchasers, or other users to meet their specific needs. Those users will specify, in other standards and specifications, which test methods and conditioning procedures are applicable and will specify any performance categories or levels. 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Compression Resistance of Helmets

ASTM E3342/E3342M-22e1 执法和惩教人员在暴力情况下维持秩序时专用的非防弹头盔规范

1.1 This specification specifies performance requirements, conditioning procedures, and test methods for assessing nonballistic-resistant head protection (that is, helmet and face shield) specifically designed to be worn by law enforcement and corrections officers when maintaining order in violent situations. 1.2 This specification does not address eye protection other than face shields that are attached to the helmet. 1.3 The threats and hazards addressed in this specification were identified by officers specially trained and equipped to manage any form of public gathering, ranging from concerts, parades, marches, and demonstration events to violent unrest. 1.4 It is anticipated that this specification will be referenced by suppliers, certifiers, purchasers, or other users to meet their specific needs. 1.5 The user of this specification may choose to specify additional requirements, and some options are provided in Appendix X1. 1.6 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Specification for Nonballistic-resistant Helmets Specifically Designed to be Worn by Law Enforcement and Corrections Officers When Maintaining Order in Violent Situations

T/JSMBPA 002-2022 儿童头盔评价规则

本标准的主要技术内容包括范围、保护性能（头盔吸收侧碰能量的性能、头盔吸收碰撞能量的性能）、佩戴装置有效性（佩戴装置强度、佩戴装置扣合装置的耐久性）、头盔佩戴的舒适性（头盔质量、佩戴装置、异味）、化学安全性（可迁移元素、邻苯二甲酸酯）。

Evaluation rules for children's helmets

T/UONZ 1-2022 智能施工安全帽

文件规定了智能施工安全帽的技术要求、试验方法、标识和检验规则

Intelligent construction helmet

ASTM F1776-21 彩弹运动用眼睛保护装置的标准规范

Standard Specification for Eye Protective Devices for Paintball Sports