共找到 1187 条与 头部防护设备 相关的标准,共 80 页
Washable reusable community face coverings – Requirements and test methods – AMENDMENT 1
Eye and face protection -- Guidance on selection, use and maintenance (ISO 19734:2021)
Eye and face protection - Protection against laser radiation - Part 1: Requirements and test methods (ISO 19818-1:2021)
Eye and face protection – Protection against laser radiation – Part 1: Requirements and test methods (ISO 19818-1:2021)
ISO 10256-2:2016 specifies performance requirements and test methods for head protectors for use in ice hockey and is intended to be read in conjunction with ISO 10256‑1. Requirements and the corresponding test methods, where appropriate, are given for the following: a) construction and protected area; b) shock absorption; c) penetration; d) retention system properties; e) field of vision; f) marking and information. ISO 10256-2:2016 applies to head protectors worn by - players other than goalkeepers, and - certain functionaries (e.g. referees). NOTE 1 The requirements of a Clause take precedent over a figure. NOTE 2 The intent of this part of ISO 10256 is to reduce the risk of injury to the head without compromising the form or appeal of the game.
Protective equipment for use in ice hockey — Part 2: Head protection for skaters
ISO 10256-3:2016 specifies performance requirements and test methods for face protectors (including visors) for use in ice hockey and is intended to be used in conjunction with ISO 10256‑1. Requirements and the corresponding test methods, where appropriate, are given for the following: a) construction and area of coverage; b) resistance to puck impact; c) penetration; d) field of vision; e) geometric (visual) optics and acuity; f) transmittance and haze; g) marking and information. ISO 10256-3:2016 applies to face protectors worn by - players other than goalkeepers, and - certain functionaries (e.g. referees). NOTE 1 The requirements of a Clause take precedent over a figure. NOTE 2 The intent is to reduce the risk of injury to the face without compromising the form or appeal of the game.
Protective equipment for use in ice hockey — Part 3: Face protectors for skaters
ISO 10256-1:2016 is part of ISO 10256 specifies general requirements for head, face, neck and body protectors (hereafter referred to as protectors) for use in ice hockey. ISO 10256-1:2016 is intended only for protectors used for ice hockey. Requirements are given for the following: a) terms and definitions; b) innocuousness; c) ergonomics; d) test report; e) permanent markings; f) information for users. In the ISO 10256 series, collateral standards specify performance requirements for protectors for use in ice hockey and are intended to be read in conjunction with ISO 10256-1:2016. NOTE 1 The requirements of a clause take precedence over a figure. NOTE 2 The intent is to reduce the risk of injury to an ice hockey player without compromising the form or appeal of the game. These standards presume that the rules of play for ice hockey will be followed by players and enforced by officials.
Protective equipment for use in ice hockey — Part 1: General requirements
1.1?These test methods describe the tests for ballistic-resistant head protection which consists of helmets and face shields. Test methods address backface deformation, resistance to penetration, and ballistic limit. It is anticipated that these test methods will be referenced b
Standard Test Methods for Ballistic Resistant Head Protection
Eye and face protection against intense light sources used on humans and animals for cosmetic and medical applications - Part 1: Specification for products (ISO/FDIS 12609-1:2021)
Eye and face protection. Guidance on selection, use and maintenance
Eye and face protection – Protection against laser radiation – Part 1: Requirements and test methods
This document is applicable to protectors intended to provide protection against accidental exposure to laser radiation within the wavelength range 180 nm to 1 mm. It specifies the requirements, test methods and marking. Protectors intended for adjustment work on lasers are included in the scope of this document and are marked in the same way as other protectors, but selection of appropriate eyewear for a specific application is a choice of the user. Laser protective filters used as viewing windows in laser equipment machinery or incorporated into optical instruments such as operating microscopes and loupes that may be used for deliberate viewing of laser radiation as part of their function are outside the scope of this document. Laser radiation in the wavelength range below 180 nm is absorbed in air, therefore eye and face protection should not be required. This document is applicable to devices intended for patient protection during medical laser procedures except for treatment in the periorbital area. Guidance on eye protectors for patients (including those used for periorbital treatment) is given in ISO/TR 22463.
Eye and face protection — Protection against laser radiation — Part 1: Requirements and test methods
Hearing protectors - Testing - Part 1: Physical test methods
Hearing protectors - Testing - Part 2: Acoustic test methods
Hearing protectors - Safety requirements - Part 6: Earmuffs with safety-related audio input
Hearing protectors - Safety requirements - Part 4: Level-dependent earmuffs
Hearing protectors - Safety requirements - Part 8: Entertainment audio earmuffs
Hearing protectors - Safety requirements - Part 9: Earplugs with safety-related audio input
Hearing protectors - Safety requirements - Part 10: Entertainment audio earplugs
Hearing protectors - Safety requirements - Part 5: Active noise reduction earmuffs
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号