21.060.01 紧固件综合 标准查询与下载

DIN EN 14399-1:2015 预加负荷用高强度结构螺栓组件.第1部分:一般要求;德文版本EN 14399-1-2015

High-strength structural bolting assemblies for preloading - Part 1: General requirements; German version EN 14399-1:2015

BS EN 14399-1:2015 用于预载的高强度结构螺栓组件 一般要求

High-strength structural bolting assemblies for preloading. General requirements

BS EN 14399-2:2015 用于预载的高强度结构螺栓组件 预载适用性

High-strength structural bolting assemblies for preloading. Suitability for preloading

DIN 20000-6:2015 建筑物中建筑产品的应用. 第6部分: 符合DIN EN 14592和DIN EN 14545的销型紧固件和连接器

Application of construction products in structures - Part 6: Dowel-type fasteners and connectors according to DIN EN 14592 and DIN EN 14545

EN 14399-2:2015 预负载高强度结构螺栓组件.第2部分:预加负荷的适合性试验

This European Standard specifies the technical requirements for high-strength structural bolting assemblies in order to ensure the suitability for preloading of bolted connections in metallic structures. A suitability test is specified to check the behaviour of the structural bolting assemblies so as to ensure that the required preload can be reliably obtained by the tightening methods specified in EN 1090-2 with sufficient margins against overtightening and against failure.

High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading

EN 14399-4:2015 预负载高强度结构螺栓组件.第4部分:HV系统.六螺栓和螺母组件

This European Standard specifies together with EN 14399-1 and EN 14399-2, the requirements for assemblies of high-strength structural bolts and nuts of system HV suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 10.9/10. Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As 1) according to EN 1993-1-8 (Eurocode 3) and to obtain ductility predominantly by plastic deformation of the engaged threads. For this purpose the components have the following characteristics: - nut height approximately 0,8 d; - bolt with short thread length. Bolting assemblies in accordance with this document include washers according to EN 14399-6. NOTE Attention is drawn to the importance of ensuring that the bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made. General requirements and requirements for suitability for preloading are specified in EN 14399-2. Clamp lengths and grip lengths for the bolting assemblies are specified in the normative Annex A.

High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies

EN 14399-1:2015 预加负荷用高强度结构螺栓组件.第1部分:一般要求

This European Standard specifies the general requirements for bolt/nut/washer(s) assemblies for high-strength structural bolting, which are suitable for preloading. The intended use of bolting assemblies in accordance with this European Standard is structural metallic works. NOTE 1 High-strength structural bolting assemblies in accordance with EN 14399-2 to EN 14399-10 are designed to fulfil the requirements of this European Standard. NOTE 2 High-strength structural bolting assemblies are suitable for preloading in accordance with EN 1090-2 in steel structures. High-strength structural bolting assemblies smaller than M12 are not designed to be preloaded. High-strength structural bolting assemblies are not designed to be welded. Railway rail fasteners are not covered by this standard.

High-strength structural bolting assemblies for preloading - Part 1: General requirements

EN 14399-3:2015 预加载的高强度结构螺栓装配.第3部分:系统洛氏硬度.六角形螺栓和螺母

This European Standard specifies, together with EN 14399-1 and EN 14399-2, the requirements for assemblies of high-strength structural bolts and nuts of system HR suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 8.8/8 or 8.8/10 and 10.9/10. Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As 1) according to EN 1993-1-8 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics: - normal nut height (style 1), see EN ISO 4032; - thread length of the bolt according to ISO 888. Bolting assemblies in accordance with this document include washers according to EN 14399-6 or to EN 14399-5 (under the nut only). NOTE Attention is drawn to the importance of ensuring that bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made. General requirements and requirements for suitability for preloading are specified in EN 14399-2. Clamp lengths and grip lengths for the bolting assemblies are specified in the normative Annex A.

High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies

ASTM F959-15 使用结构紧固件的可压缩洗衣机类型直接张力指示器的标准规格

1.1 This specification covers the requirements for compressible-washer-type direct tension indicators, (DTIs) capable of indicating the achievement of a specified minimum bolt tension in a structural bolt. 1.2 Eight types of DTIs in nominal diameter sizes 1/2 through 11/2 in. as well as M16 through M36 are covered: 1.2.1 Type 325-1—DTIs for use with Specification A325 Type 1 bolts or F8201; or F1852 assemblies. 1.2.2 Type 325–3—DTIs for use with Specification A325 Type 3 bolts or F1852 Type 3 assemblies. 1.2.3 Type 490–1—DTIs for use with Specification A490 Type 1 bolts or F2280 assemblies. 1.2.4 Type 490–3—DTIs for use with Specification A490 Type 3 F2280 Type 3 assemblies. 1.2.5 Type 8.8-1—DTIs for use with Specification A325M Type 1 bolts. 1.2.6 Type 8.8-3—DTIs for use with Specification A325M Type 3 bolts. 1.2.7 Type 10.9-1—DTIs for use with Specification A490M Type 1 bolts. 1.2.8 Type 10.9-3—DTIs for use with Specification A490M Type 3 bolts. 1.3 DTIs are intended for installation under either a bolt head or a hardened washer. (See Research Council on Structural Connections: Specification for Structural Joints Using High–Strength Bolts.) 1.4 This specification provides for furnishing Type 3 DTIs to a Chemical Composition Requirement or a Corrosion Resistance Index (CRI) at the manufacturer’s discretion. 1.5 Terms used in this specification are defined in Terminology F1789 unless otherwise specified. 1.6 The following precautionary statement pertains only to the test method portions, S......

Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners

GOST ISO 3269-2015 紧固件. 验收检验

Fasteners. Acceptance inspection

ASTM F1941/F1941M-15 机械紧固件, 英制和米制的电镀层的标准规格

1.1 This specification covers application, performance and dimensional requirements for electrodeposited coatings on threaded fasteners with unified inch and metric screw threads, but it may also be applied to other threaded parts and non-threaded parts such as washers and pins. It specifies coating thickness, supplementary hexavalent chromate or non-hexavalent conversion finishes, corrosion resistance, precautions for managing the risk of hydrogen embrittlement and hydrogen embrittlement relief for high-strength and surface-hardened fasteners. It also highlights the differences between barrel and rack plating and makes recommendations as to the applicability of each process. 1.2 The values stated in inch-pound units and SI metric units. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance to the standard. 1.3 Terms used in this specification are defined in Terminology F1789. 1.4 The following precautionary statement pertains to the test method portion only, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Electrodeposited Coatings on Mechanical Fasteners, Inch and Metric

ASTM A437/A437M-15 高温加工用热处理专用不锈钢和合金钢涡轮式锚杆支护的标准规格

1.1 This specification2 covers stainless and alloy-steel bolting material and bolting components specially heat treated for high-temperature service, such as steam turbine, gas turbine, and similar uses. See Specification A962/A962M for the definition of bolting. This material requires special processing and should not be used in general-purpose applications. Bolting furnished as bars shall be hot wrought and may be further processed by centerless grinding or by cold drawing. 1.2 The high-temperature properties of the bolting materials and components covered by this specification are dependent upon special heat treatment, which is required. Although the high-temperature properties are not specified, they are implied by control of the chemistry, heat treatment, and room-temperature properties of the bolting material. 1.3 Three levels of bolting strength are covered, designated Grades B4B, B4C, and B4D. 1.4 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.5 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract. 1.6 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Stainless and Alloy-Steel Turbine-Type Bolting Specially Heat Treated for High-Temperature Service

GOST ISO 16047-2015 紧固件. 扭矩/夹紧力试验

Fasteners. Torque/clamp force testing

ASTM A540/A540M-15 用于特殊用途的合金钢螺栓连接的标准规格

1.1 This specification2 covers regular and special-quality alloy steel bolting materials and bolting components that may be used for nuclear and other special applications. See Specification A962/A962M for the definition of bolting. 1.2 The following referenced common requirements are indispensable for application of this specification: Specification A962/A962M. 1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. These supplementary requirements only apply when specified individually by the purchaser in the purchase order or contract. 1.4 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable “M” specification designation (SI units), inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Alloy-Steel Bolting for Special Applications

ASTM A962/A962M-15 用于从低温至蠕变范围内任何温度的螺栓通用要求标准规格

1.1 This specification covers a group of common requirements that shall apply to carbon, alloy, stainless steel, and nickel alloy bolting under any of the following ASTM Specifications (or under any other ASTM Specifications that invoke this specification or portions thereof): Title of Specifications ASTM Designation Alloy-Steel and Stainless Steel Bolting Materials 8199;for High-Temperature Service A193/A193M Carbon and Alloy Steel Nuts for Bolts for High 8199;Pressure and High-Temperature Service A194/A194M Alloy Steel Bolting Materials for Low-Temperature 8199;Service A320/A320M Alloy-Steel Turbine-Type Bolting Material 8199;Specially Heat Treated for High-Temperature 8199;Service A437/A437M High-Temperature Bolting Materials With Expansion 8199;Coefficients Comparable to Austenitic Stainless 8199;Steels A453/A453M Alloy-Steel Bolting Materials for Special Applications A540/A540M Precipitation-Hardening Bolting Material (UNS 8199;N07718) for High Temperature Service A1014/A1014M 1.2 In case of conflict, the requirements of the individual product specification shall prevail over those of this specification. 1.3 Fasteners are a wide-ranging classification that includes screws, bolts, nuts, washers, stud bolts, rivets, powder-actuated studs, staples, tacks, and pins. Bolting, which is composed of bolting materials, such as rods, bars, flats, and forgings, which are subsequently manufactured into bolting ......

Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range

ASTM A453/A453M-15 使用与奥氏体不锈钢可比的膨胀系数对高温螺栓连接的标准规格

1.1 This specification2 covers five grades of bolting materials with twelve classes of yield strength ranging from 50 to 120 ksi [345 to 827 MPa] for use in high-temperature service for bolting components, such as bolts, screws, nuts, or studs, for pressure vessel and valve flanges. See Specification A962/A962M for the definition of bolting. The material requires special processing and is not intended for general purpose applications. 1.2 The following referenced general requirements are indispensable for application of this specification: Specification A962/A962M. 1.3 Supplementary Requirements are provided for use at the option of the purchaser. The Supplementary Requirements shall only apply when specified individually by the purchaser in the purchase order or contract. 1.4 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable “M” specification designation (SI units), the inch-pound units shall apply. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels

ASTM F1667-15 楔入式紧固件的标准规格: 钉子, 长钉和u形钉

1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Note 1: Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65. (A) All dimensions given in inches. (A) All dimensions are given in inches. (A) All dimension are given in inches. (A) All dimensions are given in inches. (A) All dimensions are given in inches.(B) Dashes (—) indicate that the fastener size is not a standard size. †8201;Editorially corrected in March 2012. (A) All dimensions are given in inches.(B) Dashes (—) indicate that the fastener size is not a standard size. L   =   length, in., H   = &......

Standard Specification for Driven Fasteners: Nails, Spikes, and Staples

GOST ISO 16426-2015 紧固件. 质量保证系统

Fasteners. Quality assurance system

GSO ISO 16048:2014 耐腐蚀不锈钢紧固件的钝化

This International Standard specifies the methods most often used for passivation of corrosion-resistant stainless steel fasteners. Typical anodic dissolution behaviour of an active-passive-transpassive metal is given in Annex A.

Passivation of corrosion-resistant stainless-steel fasteners

GSO ISO 16047:2014 紧固工具 扭矩/固定强度测试

This International Standard specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts. It is applicable, basically, to bolts, screws, studs and nuts made of carbon steel and alloy steel, whose mechanical properties are specified in ISO 898-1, ISO 898-2 or ISO 898-6, having ISO metric threads with thread sizes M3 to M39. It is also applicable to the combination of other externally and internally threaded fasteners with a triangular ISO thread according to ISO 68-1. It is not applicable to set screws and similar threaded fasteners that are not under tensile stresses, nor to screws which form their own mating thread or threaded fasteners having additional self-locking features. Unless otherwise agreed, the tests are carried out at room temperature. However, tests carried out under standard conditions are made at a temperature of 10 °C to 35 °C. This method allows determination of the tightening characteristics of threaded fasteners and related parts.

Fasteners -- Torque/clamp force testing