21.060.40 铆钉 标准查询与下载

ASTM B316/B316M-20 铝和铝合金铆钉和冷加工线和棒的标准规范

1.1 This specification covers wire and rod in the alloys (Note 1) shown in Table 1 and the tempers shown in Table 2 [Table 3] and Table 4 [Table 5], suitable for manufacturing rivets and other similar items by cold-heading operations. NOTE 1—Throughout this specification the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. NOTE 2—For rolled or cold-finished wire and rod, see Specification B211, and for extruded wire and rod, see Specification B221. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1 The SI units are shown either in brackets or in separate tables. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods

ASTM A31-14(2020) 铆钉和压力容器钢铆钉和标准规范

1.1 This specification2 covers steel rivets for use in boilers and pressure vessels and steel bars for use in the manufacture of rivets. 1.2 Two grades are covered: 1.2.1 Grade A—Bars having a yield point of 23 000 psi (160 MPa) minimum with carbon 0.18 % maximum. 1.2.2 Grade B—Bars having a yield point of 29 000 psi (200 MPa) minimum with carbon 0.28 % maximum. 1.2.3 Rivets are manufactured from the applicable bar grade. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Steel Rivets and Bars for Rivets, Pressure Vessels

KS B ISO 15976-2020 带拉芯凸头闭端抽芯铆钉 St/St

Closed end blind rivets with break pull mandrel and protruding head－St/St

KS B ISO 15975-2020 闭式拉芯凸头抽芯铆钉 AI/AIA

Closed end blind rivets with break pull mandrel and protruding head－AI/AIA

T/ZZB 1728-2020 汽车用环槽铆钉连接副

本文件规定了汽车用环槽铆钉连接副的术语和定义、型式、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存和质量承诺。 本文件适用于公称直径6 mm～10 mm的10.9 R级汽车用Ⅰ型环槽铆钉连接副（以下简称“连接副”），含带定位轴肩Ⅰ型环槽铆钉连接副。

Ring groove rivet assemblies for automobile

KS B ISO 15979-2019 拉断芯杆凸头开口抽芯铆钉 St/St

Open end blind rivets with break pull mandrel and protruding head－St/St

KS B ISO 15984-2019 沉头开口抽芯铆钉 A2/A2

Open end blind rivets with break pull mandrel and countersunk head－A2/A2

KS B ISO 15983-2019 断芯凸头开口抽芯铆钉 A2/A2

Open end blind rivets with break pull mandrel and protruding head－A2/A2

KS B ISO 16583-2019 带拉断芯轴和沉头的开口抽芯铆钉 Cu/St 或 Cu/Br 或 Cu/SSt

Open end blind rivets with break pull mandrel and countersunk head－Cu/St or Cu/Br or Cu/SSt

KS B ISO 15977-2019 拉断芯杆凸头开口抽芯铆钉 AlA/St

Open end blind rivets with break pull mandrel and protruding head－AlA/St

KS B ISO 16582-2019 带断拉心轴和凸头的开口抽芯铆钉 Cu/St 或 Cu/Br 或 Cu/SSt

Open end blind rivets with break pull mandrel and protruding head－Cu/St or Cu/Br or Cu/SSt

KS B ISO 15981-2019 拉断芯杆凸头开口抽芯铆钉 AlA/AlA

Open end blind rivets with break pull mandrel and protruding head－AlA/AlA

KS B ISO 15980-2019 沉头开口抽芯铆钉 St/St

Open end blind rivets with break pull mandrel and countersunk head－St/St

KS B ISO 16584-2019 带断拉心轴和凸头的开口抽芯铆钉 NiCu/St 或 NiCu/SSt

Open end blind rivets with break pull mandrel and protruding head－NiCu/St or NiCu/SSt

KS B ISO 15978-2019 沉头开口抽芯铆钉 AlA/St

Open end blind rivets with break pull mandrel and countersunk head－AlA/St

KS B ISO 15982-2019 沉头开口抽芯铆钉 AlA/AlA

Open end blind rivets with break pull mandrel and countersunk head－AlA/AlA

KS B ISO 16585-2019 抽芯凸头闭端抽芯铆钉 A2/SSt

Closed end blind rivets with pull mandrel and protruding head－A2/SSt

T/ZZB 1136-2019 汽车发动机冷却用膨胀水壶

本标准规定了汽车发动机冷却用膨胀水壶(以下简称膨胀水壶)的术语与定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本标准适用于各种汽车发动机冷却系统中的膨胀水壶。

Coolant expansion tank of automotive engine

ASTM F3329-18 碳钢和合金钢米制铆钉的标准规范

1.1 This specification covers chemical and mechanical requirements for nine property classes of carbon and alloy steel metric rivets in nominal diameters M01 through M36 suited for use in general engineering applications. 1.2 This specification does not cover dimensional requirements for rivets of any property class. When referencing this specification for procurement purposes, it is mandatory that size, type, style, and any special dimensions of the product be additionally specified. 1.2.1 In case of any conflict in requirements, the requirements of the individual product specification shall take precedence over those of this general specification. 1.2.2 The purchaser may specify additional requirements which do not negate any of the provisions of this general specification or of the individual product specification. Such additional requirements, the acceptance of which are subject to negotiation with the supplier, must be included in the order information (see Section 3). 1.3 When agreed on by the purchaser, Class 5.8 fasteners may be supplied when either Classes 4.6 or 4.8 are ordered; Class 4.8 may be supplied when Class 4.6 is ordered; 1.4 The product size range for which each property class is applicable is given in Table 1 on chemical composition requirements, and the mechanical requirements table (see Table 2). 1.5 Appendix X1 explains the significance of the property class designation numerals. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Carbon and Alloy Steel Metric Rivets

T/ZZB 0662-2018 P2混合动力系统销钉

本标准规定了P2混合动力系统销钉的术语和定义、基本要求、技术要求、试验方法、检验规则、判定规则、标识、包装、运输和储存、质量承诺。 本标准适用于直径范围在≥3 mm，≤20 mm的P2混合动力系统销钉（以下简称为销钉）。

P2 hybrid drive system pin