21.060.40 铆钉 标准查询与下载
共找到 500 条与 铆钉 相关的标准，共 34 页
Round head rivets - Nominal diameters 1 mm to 8 mm
- ICS
- 21.060.40
- CCS
- 发布
- 2011-03
- 实施
Steel round head rivets - Nominal diameters from 10 mm to 36 mm
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-03
- 实施
This Standard specifies dimensions, masses and technical delivery conditions for flat countersunk head rivets with nominal diameters from 1,4mm to 6mm.
Flat round head rivets - Nominal diameters 1,4 mm to 6 mm
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-03
- 实施
This Standard specifies dimensions, masses and technical delivery conditions for semi-tubular countersunk head rivets with nominal diameters from 1,6mm to 10mm.
Semi-tubular pan head rivets - Nominal diameters 1,6 mm to 10 mm
- ICS
- 21.060.40
- CCS
- 发布
- 2011-03
- 实施
This Standard specifies dimensions, masses and technical delivery conditions for semi-tubular countersunk head rivets with nominal diameters from 1,6mm to 10mm.
Semi-tubular countersunk head rivets - Nominal diameters 1,6 mm to 10 mm
- ICS
- 21.060.40
- CCS
- 发布
- 2011-03
- 实施
This Standard specifies dimensions, masses and technical delivery conditions for flat countersunk head rivets with nominal diameters from 3mm to 5mm.
Flat countersunk head rivets - Nominal diameters 3 mm to 5 mm
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-03
- 实施
This Standard specifies dimensions, masses and technical delivery conditions for flat countersunk head rivets with nominal diameters from 1,6mm to 6mm.
Mushroom head rivets - Nominal diameters 1,6 mm to 6 mm
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-03
- 实施
This Standard specifies dimensions, masses and technical delivery conditions for flat countersunk head rivets with nominal diameters from 1mm to 8mm.
Countersunk head rivets - Nominal diameters 1 mm to 8 mm
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-03
- 实施
Hollow rivets, one piece, drawn from strip
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-02
- 实施
This Standard specifies technical delivery conditions,test methods and acceptance conditions for all types of standardized rivets(except for blind rivets).These specifications are generally applicable but may deviate from the specifications of other relevant proudct standards, in which case the latter take precedence, Subject to agreement,the specifications of this standard may also be used for non-standardized rivets.
Rivets - Technical specifications
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-02
- 实施
Open end blind rivets with break pull mandrel and protruding head - AlA/St (ISO 15977:2002); German version EN ISO 15977:2002
- ICS
- 21.060.40
- CCS
- J13
- 发布
- 2011-02
- 实施
Aerospace series - Rivet, 100° reduced flush head, close tolerance - Inch series
- ICS
- 21.060.40
- CCS
- 发布
- 2010-03-15
- 实施
- 2010-03-15
1.1 This specification covers wire and rod in the alloys (Note 1) shown in Table 1 and the tempers shown in Table 2 [Table 3] and Table 4 [Table 5], suitable for manufacturing rivets and other similar items by cold-heading operations. Note 18212;Throughout this specification the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 28212;For rolled or cold-finished wire and rod, see Specification B211, and for extruded wire and rod, see Specification B221. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1 The SI units are shown either in brackets or in separate tables.
Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
- ICS
- 21.060.40
- CCS
- H61
- 发布
- 2010
- 实施
Closed end blind rivets with break pull mandrel and countersunk head－AIA/St
- ICS
- 21.060.40
- CCS
- 发布
- 2008-10-14
- 实施
이 표준은 알루미늄 합금 몸체(AIA)와 강 맨드릴(St)로 되어 있고, 공칭 지름 3.2
Closed end blind rivets with break pull mandrel and countersunk head-AIA/St
- ICS
- 21.060.40
- CCS
- J10
- 发布
- 2008-10-14
- 实施
- 2008-10-14
Closed end blind rivets with break pull mandrel and countersunk head－AIA/St
- ICS
- 21.060.40
- CCS
- 发布
- 2008-10-14
- 实施
Closed end blind rivets with break pull mandrel and protruding head－AIA/St
- ICS
- 21.060.40
- CCS
- 发布
- 2008-06-03
- 实施
Closed end blind rivets with break pull mandrel and protruding head－AIA/St
- ICS
- 21.060.40
- CCS
- 发布
- 2008-06-03
- 实施
이 표준은 알루미늄 합금 몸체(AIA)와 강 맨드릴(St)로 되어 있고, 공칭 지름 3.2
Closed end blind rivets with break pull mandrel and protruding head－AIA/St
- ICS
- 21.060.40
- CCS
- J10
- 发布
- 2008-06-03
- 实施
- 2008-06-03
