23.020.10 固定容器和罐 标准查询与下载

KS M 3511-2021 吹塑聚乙烯容器

Blow－molded polyethylene containers

NF E86-100:2021 容器. 圆形检查或出入开孔

Storage tanks - Round examination or access openings

DB62/T 4397-2021 天然气加气站高压储气瓶组在线检验规范

Specifications for online inspection of high-pressure gas storage cylinders in natural gas filling stations

DB62/T 4396-2021 高压天然气储气井定期检验规范

Specifications for Periodic Inspection of High Pressure Natural Gas Storage Wells

ASTM E2681-21 储存规定物质的地下储罐系统的环境管理标准指南

1.1?The framework discussed in this guide is limited to facilities with underground storage tanks (USTs) storing regulated substances at ambient temperature and atmospheric pressure. This guide is not intended to provide detailed technical specifications for implementation of th

Standard Guide for Environmental Management of Underground Storage Tank Systems Storing Regulated Substances

EN 13121-1:2021 地上使用的GRP罐和容器.第1部分:原材料.验收条件和技术条件

GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance criteria

KS B 6283-2021 储油罐风荷载、地震荷载设计要求

Design requirements for wind load and seismic load of oil storage tanks

ASTM D1998-21 聚乙烯立式储罐的标准规范

1.1 This specification covers flat-bottom, upright, cylindrical tanks molded in one-piece seamless construction by rotational molding. The tanks are molded from polyethylene for above ground, vertical installation and are capable of containing aggressive chemicals at atmospheric pressure. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship and appearance. Tank capacities are from 1900 L (500 gal) up. 1.2 This specification covers the design of stationery vessels for use at atmospheric pressure intended for use with liquids heated below their flash points and continuous service temperatures below 66°C (150°F) for Type I tanks and below 60°C (140°F) for Type II tanks. 1.2.1 NFPA Standards 30 and NFPA 31 shall be consulted for installations that are subject to the requirements of these standards. 1.3 For service requirements beyond the scope of this specification (1.2), such as externally imposed mechanical forces, internal pressure or vacuum, higher temperature service, etc., other relevant sources of standards, for example, local and state building codes, NFPA, ASME, ARM, etc., shall be consulted. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. NOTE 1—ISO 13341:2005+A1:2011 and ISO 13575:2012 are similar, but not equivalent to this standard. 1.5 The following precautionary caveat pertains only to the test methods portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polyethylene Upright Storage Tanks

GSO 1831:2021 滚塑聚乙烯储水箱

This Gulf standard covers the requirement of the mono layer or more rotational molded polyethylene water storage vertical and horizontal tanks, dimensions and construction. This standard is applicable to water storage tanks with a nominal service temperature from 1°C to 60°C. This standard is not applicable to underground or mobile water tanks.

Rotational molded Polyethylene Water Storage Tanks

DIN/TS 26059-1:2021 用于对水生环境有害的液体的溢出保护装置的组件 第1部分：用于溢出保护系统的传感器和发射器以及用于自给式溢出保护的组件的制造

This Technical Specification applies to the manufacture of sensors and transmitters for overfill protection devices and components for self-contained overfill protection devices in stationary and stationary-use containers with water-polluting liquids. This Technical Specification

Components for overfill protection devices for liquids hazardous to aquatic environment — Part 1: Manufacture of sensors and transmitters for overfill protection systems as well as components for self-sufficient overfill protection

T/CATSI 05004-2021 小型液化石油气（商品丙烷）储罐

本标准规定了储罐的结构和规格、材料与外购件、设计、安全附件、仪表、装卸附件、制造、试验方法、检验规则、标志标识、出厂文件和运输包装等要求。   

Small liquefied petroleum gas (commercial propane) storage tank

CSA ANSI/CAN/UL/ULC 2152-2021 用于特定可燃或不可燃液体的特殊用途非金属容器和罐体

Special Purpose Nonmetallic Containers and Tanks for Specific Combustible or Noncombustible Liquids

DB4102/T 008-2020 压力容器质量记录复核规范

Specification for review of pressure vessel quality records

DIN CEN/TR 13121-5:2020 地上使用的GRP 罐和容器. 第5部分: GRP 容器的示例计算; 德文版 CEN/TR 13121-5-2017

This Technical report gives guidance in use of the standard EN 13121 GRP tanks and vessels for use above ground. Found necessary due to the complexity of the standard and for the understanding of how the standard complies with EN 1990:s principles and requirements for safety, ser

GRP tanks and vessels for use above ground - Part 5: Example calculation of a GRP-vessel; German version CEN/TR 13121-5:2017

NB/T 47012-2020 制冷装置用压力容器

本文件规定了以液化气体为制冷剂、设计压力不高于5.0MPa、设计温度不高于200℃的制冷装置用压力容器（包括制冷装置用管壳式热交换器，以下简称“容器”）的设计、制造、检验与验收要求。

Pressure vessels for refrigeration equipment

DB34/T 1973-2020 天然气加气站高压气瓶组在线检验规程

On-line inspection procedures for high-pressure gas cylinders in natural gas filling stations

DB37/T 3964-2020 大型浮顶储罐安全技术规程

Safety technical regulations for large floating roof storage tanks

DB42/T 1542-2020 电站锅炉范围内管道安装、改造、重大修理监督检验规则

Supervision and inspection rules for pipeline installation, modification, and major repairs within the scope of power plant boilers

T/CMES 16002-2019 钢制塔式容器风致疲劳寿命计算及评定方法

本标准规定了钢制塔式容器风致疲劳寿命的计算和评定方法。 本标准适用于高度大于30m，且常年处于多风地区的裙座自支撑钢制塔式容器

Calculation and evaluation method of wind-induced fatigue life of steel tower vessel

KS B 6971-2019 LNG储罐风险评估标准

Standard for risk assessment of LNG storage tanks