23.020.10 固定容器和罐 标准查询与下载

ASTM D4865-19 石油燃料系统中静电产生和耗散的标准指南

1.1 This guide describes how static electricity may be generated in petroleum fuel systems, the types of equipment conducive to charge generation, and methods for the safe dissipation of such charges. This guide is intended to increase awareness of potential operating problems and hazards resulting from electrostatic charge accumulation. 1.2 This guide is not intended to provide specific solutions but indicates available techniques the user may wish to investigate to alleviate electrostatic charges. This guide does not cover the effects of stray currents or of lightning, either of which can also produce sparks leading to fires or explosions. 1.3 This guide is not intended to address detailed safety practices associated with static electricity in petroleum product systems. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems

T/CASEI 21001-2019 现场制造压力容器监督检验规范

本标准适用于《固定式压力容器安全技术监察规程》（TSG21—2016 ）适用范围内压力容器（不包括超高压容器、地下储气井、非金属及非金属衬里压力容器）现场制造的监督检验工作。 本标准重点描述大型压力容器（含球罐）在使用现场（区别于制造厂内）的制造监检程序、方法和内容，包括：制造单位的资格、项目告知、分包的控制、组对的控制、焊接现场的控制、焊接试验件的控制、热处理的控制、耐压试验的控制以及制造单位质量保证体系运行情况的评价等方面。

Supervision Inspection Specification for Manufacturing Pressure Vessel on Site

ASTM C1393-14(2019) 管道和罐用垂直定向矿物纤维卷和薄板绝热材料的标准规范

Standard Specification for Perpendicularly Oriented Mineral Fiber Roll and Sheet Thermal Insulation for Pipes and Tanks

T/ZJASE 001-2019 固定式高压储氢用钢带错绕式容器定期检验与评定

本标准规定了按照GB/T 26466设计制造的固定式高压储氢用钢带错绕式容器(以下简称储氢容器)定期检验的基本要求、检验类别、检验周期、检验项目和方法、结论评定及检验报告的技术要求

Periodic Inspection and Assessment of Stationary Flat Steel Ribbon Wound Vessels for Storage of High Pressure Gaseous Hydrogen

ANSI/CAN/UL/ULC 1316:2018 易燃和可燃液体纤维增强地下储罐标准

1 Scope 1.1 This Standard sets forth minimum design and construction requirements for fibre reinforced plastic, non-pressure tanks that are used for the underground storage of flammable and combustible liquids, such as: a) Petroleum products, including petroleum hydrocarbon fuels with low-biofuels blends, per specifications, and similar flammable or combustible liquid petroleum derivatives, such as fuel components (cetane, hexane, heptane), and oils (lubricating, hydraulic, machine); b) Oxygenated fuel blends, including all "petroleum product" liquids plus petroleum hydrocarbon fuels with low-biofuels blends; c) Oxygenates, including all “petroleum product” and "oxygenated fuel blends" liquids plus pure/ denatured or highest oxygenated blend stocks for use in mixing of dispensed lower fuel-blends and components, such as biodiesel and ethanol; and d) Other flammable and combustible liquids (for which the test fuels in Appendix A are not considered to be sufficient or applicable) that can be demonstrated or determined to be compatible with the reinforced plastic underground tank materials as determined by the certifier. In addition to this Standard’s traditional safety requirements for underground fiber reinforced plastic tanks that primarily evaluate structural integrity, material compatibility and mitigate environmental hazards from loss of liquid containment under expected normal conditions; optional construction and/or performance requirements, and associated ratings, intended to address more severe conditions associated with the effects of Climate Change are included in Appendix F. NOTE: The test fuels in Appendix A are considered to be sufficient and representative for US or Canadian approved motor fuels, offroad fuels, gasoline from renewable and petroleum feedstocks, diesel, renewable diesel, synthetic diesel, biodiesel, kerosene, aviation fuels, jet fuels, fuel oil and heating oil as referenced in (a), (b), and (c). 1.2 This Standard covers tanks of either single, double or multiple wall construction. 1.3 Tanks covered by this Standard are fabricated, inspected, and tested for leakage prior to shipment from the factory as completely assembled vessels. 1.4 This Standard covers tanks where the primary tank may have a single compartment or have multiple compartments. 1.5 These tanks are intended for installation and use in accordance with applicable documents in the following list: a) In Canada: 1) National Fire Code of Canada; 2) CAN/CSA-B139, Installation code for oil-burning equipment; 3) CCME PN1326, Environmental Code of Practice for Aboveground and Underground Storage Tank Systems Containing Petroleum and Allied Petroleum Products; 4) Regulations of the authority having jurisdiction; and b) In the Unites States 1) Standard for the Installation of Oil-Burning Equipment, NFPA 31; 2) Flammable and Combustible Liquids Code, NFPA 30; and 3) Code for Motor Fuel Dispensing Facilities and Repair Garages, NFPA 30A, as applicable. 1.6 Accessories, such as, ladders, tank sumps, risers, and guide lugs, that do not affect tank performance and are attached to the tank internally or externally during manufacture are permitted but not covered by this standard. 1.7 Except for optional Climate Change Adaptation requirements in Appendix F, these requirements do not cover special evaluations for resistance to, or use after earthquakes, floods, high wind events, or other natural disasters. NOTE: See the Note at the beginning of Appendix F for further information on the terms “Adaptation” and “Mitigation”, as they pertain to Climate Change.

Standard for Fibre Reinforced Underground Tanks for Flammable and Combustible Liquids

DB34/T 3192-2018 埋地液化石油气储罐定期检验规程

本标准规定了埋地液化石油气储罐定期检验的检验要求、检验项目与方法、安全状况等级评定、检 验结论和检验周期等内容。 本标准适用于卧式埋地液化石油气储罐的定期检验。

Regulations for periodic inspection of buried liquefied petroleum gas storage tanks

DB34/T 1799-2018 曳引驱动可变速电梯安装验收技术条件

本标准规定了可变速电梯安装验收应遵守的安全准则。 本标准适用于额定速度不大于 2.5 m/s 的曳引驱动的可变速电梯。 本标准不适用非电力驱动以及强制驱动的可变速电梯。

Technical conditions for installation and acceptance of traction drive variable speed elevators

18/30376874 DC BS EN 13341 用于地上储存燃料的静态热塑性储罐 产品特性及测试方法

BS EN 13341. Static thermoplastic tanks for above ground storage of fuel. Product characteristics and test methods

ASTM D4097-18 接触式玻璃纤维增​​强热固性树脂耐腐蚀罐标准规范

Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

ASTM D3299-18 长丝玻璃纤维增​​强热固性树脂耐腐蚀罐的标准规范

1.1 This specification covers cylindrical tanks fabricated by filament winding for above-ground vertical installation, to contain aggressive chemicals at atmospheric pressure as classified herein, and made of a commercial-grade polyester or vinylester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance. 1.2 This specification does not cover the design of vessels intended for pressure above atmospheric or under vacuum conditions, except as classified herein, or vessels intended for use with liquids heated above their flash points. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 Special design consideration shall be given to tanks subject to environmental and/or mechanical forces such as seismic, wind, ice, agitation, or fluid dynamic forces, to operational service temperatures greater than 180°F (82°C) and to tanks with unsupported bottoms. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Filament-Wound Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks

ASTM F1657/F1657M-96(2018) 紧急连接带不兼容连接器的吊杆的标准实施规程

1.1 This practice provides a standard practice for the joining of oil spill containment boom connectors in emergencies. 1.2 The use of this connection method may adversely affect the total tensile strength of the connected booms. 1.3 These criteria are intended to define mating requirements that will allow the emergency or occasional connection of unlike connectors. 1.4 This practice is not intended to replace Specification F962. 1.5 This practice does not address the compatibility of spill control equipment with spill products. It is the user’s responsibility to ensure that any equipment selected is compatible with the anticipated spilled material. 1.6 There is no guarantee that all of the connectors in use today can accept the holes spaced as required without interfering with existing bolt holes or other connector features. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. See Note 5 in Fig. 1—dimensions A and B are critical. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see 3.2. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Emergency Joining of Booms with Incompatible Connectors

DB37/T 3078-2017 特种设备安全风险分级管控体系细则

Detailed Rules for Special Equipment Safety Risk Hierarchical Management and Control System

DB37/T 3079-2017 特种设备事故隐患排查治理体系细则

Detailed rules for the investigation and management system of hidden dangers of special equipment accidents

17/30350291 DC BS EN 14015 用于在环境温度及以上温度下储存液体的现场建造的立式、圆柱形、平底、地上、焊接钢罐的设计和制造规范

BS EN 14015. Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above

DB37/T 3069-2017 球形储罐现场制造监督检验规则

Supervision and inspection rules for on-site manufacturing of spherical storage tanks

DB41/T 1460-2017 金属常压储罐检验规范

Specification for Inspection of Metal Atmospheric Storage Tanks

DB34/T 2976-2017 高压蓄能器在线检验规程

本标准规定了高压蓄能器在线检验的一般要求、检验前准备、程序、内容和方法、检验结论。 本标准适用于高压蓄能器在线检验

High-pressure accumulator on-line inspection regulations

DB34/T 984-2017 低温绝热压力容器定期检验规程

本标准规定了在用低温绝热压力容器的定期检验一般规定、检验项目和要求、安全状况等级评定。 本标准适用于设计压力小于或等于 35.0 MPa、设计温度不大于 －20℃且不小于 －196℃的在用低 温绝热压力容器。

Regulations for Periodic Inspection of Cryogenic Insulated Pressure Vessels

DB34/T 982-2017 简单压力容器安全性能监督检验规范

本标准规定了简单压力容器安全性能监督检验的基本要求、内容、项目和方法。 本标准适用于 TSG 21 规定的同时满足以下条件的简单压力容器的安全性能监督检验（以下简称监 检）： a) 压力容器由筒体和平盖、凸形封头（不包括球冠形封头），或者由两个凸形封头组成； b) 筒体、封头和接管等主要受压元件的材料为碳素钢、奥氏体不锈钢或者 Q345R； c) 设计压力小于或者等于 1.6 MPa； d) 容积小于或者等于 1 m3 ； e) 工作压力与容积的乘积小于或者等于 1 MPa·m3； f) 介质为空气、氮气、二氧化碳、惰性气体、医用蒸馏水蒸发而成的蒸气或者上述气（汽）体的 混合气体；允许介质中含有不足以改变介质特性的油等成分，并且不影响介质与材料的相容性； g) 设计温度大于或者等于 -20℃，最高工作温度小于或者等于 150℃； h) 非直接火焰加热的焊接压力容器（当内直径小于或者等于 550 mm 时允许采用平盖螺栓连接）。

Code for supervision and inspection of safety performance of simple pressure vessels

DB34/T 983-2017 尿素合成塔定期检验规程

本标准规定了在用尿素合成塔的检验的准备、定期检验的内容和方法。 本标准适用于结构为多层包扎和整体包扎的尿素合成塔定期检验。

Regulations for periodic inspection of urea synthesis tower