23.020.10 固定容器和罐 标准查询与下载

ASTM D4865-23 石油燃料系统中静电产生和消散的标准指南

Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems

23/30459178 DC BS EN 14620-5 设计和制造现场建造的立式、圆柱形、平底储罐系统 用于储存工作温度在 0 °C 至 196 °C 之间的冷冻液化气体 第5部分 测试、干燥、吹扫和……

BS EN 14620-5. Design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196 °C - Part 5. Testing, drying, purging and…

T/QGCML 1132-2023 不锈钢热水计量罐

本文件规定了不锈钢热水计量罐的产品型号表示方法、技术要求、试验方法、检验规则、标志、包装、运输等内容。 本文件适用于不锈钢热水计量罐（以下简称“计量罐”）。

Stainless steel hot water metering tank

23/30452973 DC BS EN 14620-4 设计和制造现场建造的立式、圆柱形、平底储罐系统 用于储存工作温度在 0 °C 至 -196 °C 之间的冷冻液化气体 第 4 部分：绝缘组件

BS EN 14620-4. Design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196 °C - Part 4. Insulation components

T/CAS ES210304001-2022 工业品质量分级评价规则 钢制塔式容器

1　范围 本文件规定了钢制塔式容器质量分级的评价程序和要求、评价方法、质量分级等内容。 本文件适用于单层钢板卷焊塔式容器（含镍-钢复合钢板和镍材堆焊衬里塔式容器）质量分级评价活动，但下列产品除外： ——有色金属复合钢板塔式容器； ——有色金属堆焊衬里塔式容器； ——多层包扎结构塔式容器； ——反应容器； ——换热容器。 2　规范性引用文件 下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于本文件。 GB/T 150（所有部分） 压力容器 GB/T 4336  碳素钢和中低合金钢 多元素含量的测定 火花放电原子发射光谱法（常规法） GB/T 11170  不锈钢 多元素含量的测定 火花放电原子发射光谱法（常规法） GB/T 13298  金属显微组织检验方法 GB/T 17394（所有部分） 金属材料 里氏硬度试验 GB/T 19001/ISO9001  质量管理体系 要求 GB/T 24001/ISO14001  环境管理体系 要求及使用指南 GB/T 45001/ISO45001  职业健康安全管理体系 要求及使用指南 NB/T 47013（所有部分） 承压设备无损检测 NB/T 47014  承压设备焊接工艺评定 NB/T 47041  塔式容器 T/CAS ES000000001—2022（V01） 工业品质量分级评价规则 通则

Rules for quality grading and evaluating of industrial products—Steel verticai vessels supported by skirt

T/CCSAS 020-2022 常压储罐腐蚀监测方法与实施指南

Corrosion monitoring methods and implementation guidelines for atmospheric storage tanks

DB43/T 2513-2022 固定式钢制常压危险化学品储罐检验规范

Inspection specification for fixed steel atmospheric pressure hazardous chemical storage tanks

22/30447470 DC BS EN 13121-3 地上使用的 GRP 储罐和容器 第 3 部分. 设计和工艺

BS EN 13121-3. GRP tanks and vessels for use above ground. - Part 3. Design and workmanship

ASTM F2438-04(2022) 漏油响应臂连接标准规范:滑动连接器

1.1 This specification covers design criteria requirements, design geometry, material characteristics, and desirable features for oil spill response boom slide connections. These criteria are intended to define minimum mating characteristics and are not intended to be restricted to a specific configuration. 1.2 The specification defines the geometry required to mate with typical Universal slide connectors or Specification F962 connectors with web thickness up to 0.3 in. Some very heavy-duty or PVC connectors may exceed this dimension and not be compatible. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Oil Spill Response Boom Connection: Slide Connector

GSO ASTM D4865:2022 石油燃料系统静电产生和消散的标准指南

1.1 This guide describes how static electricity may be generated in petroleum fuel systems, the types of equipment conducive to charge generation, and methods for the safe dissipation of such charges. This guide is intended to increase awareness of potential operating problems and hazards resulting from electrostatic charge accumulation. 1.2 This guide is not intended to provide specific solutions but indicates available techniques the user may wish to investigate to alleviate electrostatic charges. This guide does not cover the effects of stray currents or of lightning, either of which can also produce sparks leading to fires or explosions. 1.3 This guide is not intended to address detailed safety practices associated with static electricity in petroleum product systems. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems

ASTM E1990-22 地下储罐系统运行符合40 CFR第280部分法规的评估标准指南

1.1 This guide covers information for evaluating tank systems for operational conformance with the Federal technical standards (including the financial responsibility requirements) for underground storage tanks (USTs) found at 40 Code of Federal Register (CFR) Part 280. 1.2 This guide does not address the corrective action requirements of 40 CFR Part 280. 1.3 To the extent that a tank system is excluded or deferred from the federal regulations under Subpart A of 40 CFR Part 280, it is not covered by this guide. 1.4 Local regulations may be more stringent than federal regulation and the reader should refer to the implementing agency to determine compliance. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Performing Evaluations of Underground Storage Tank Systems for Operational Conformance with 40 CFR, Part 280 Regulations

22/30434788 DC BS EN 14620-1 设计和制造现场建造的立式、圆柱形、平底储罐系统 用于储存工作温度在 0 °C 至 -196 °C 之间的冷冻液化气体 第 1 部分：概述

BS EN 14620-1. Design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196 °C - Part 1. General

T/HEBQIA 051-2021 系列标准化装配式高耐候罐

本文件规定了一系列标准化装配式高耐候罐制造的系列划分、基本结构、技术要求、检验方法、检 验规则、标志、包装、运输、贮存。

A series of standardized assembled high weather resistance tanks

DIN EN 13121-1:2021 地上用GRP槽罐和容器. 第1部分: 原材料. 技术条件和验收条件; 德文版本EN 13121-1-2021

This European Standard gives requirements for acceptance and usage conditions of raw materials for GRP tanks and vessels with or without lining for storage or processing of fluids, factory made or site built, non pressurised or pressurised, for use above ground.

GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance criteria; German version EN 13121-1:2021

T/LYGDL 002-2021 大气式热力旋膜除氧器

本文件规定了大气式热力旋膜除氧器(以下简称除氧器）的型号、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于工业锅炉和发电用锅炉上使用的除氧器。

Atmospheric thermal spin film deaerator

T/LYGDL 001-2021 热力除氧器乏汽回收装置

本文件规定了大气式热力旋膜除氧器(以下简称除氧器）的型号、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于工业锅炉和发电用锅炉上使用的除氧器。

Deaerator waste heat recovery device

SN EN 13121-1-2021 地上使用的 GRP 储罐和容器 第1部分：原材料 规范条件和验收标准

GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance criteria

DS/EN 13121-1:2021 地上用 GRP 储罐和容器 第1部分：原材料 规范条件和验收标准

GRP tanks and vessels for use above ground – Part 1: Raw materials – Specification conditions and acceptance criteria

KS M 3511-2021 吹塑聚乙烯容器

Blow－molded polyethylene containers

NF E86-100:2021 容器. 圆形检查或出入开孔

Storage tanks - Round examination or access openings