23.020.10 固定容器和罐 标准查询与下载
共找到 599 条与 固定容器和罐 相关的标准，共 40 页
本标准规定了简单压力容器安全性能监督检验的基本要求、内容、项目和方法。 本标准适用于 TSG 21 规定的同时满足以下条件的简单压力容器的安全性能监督检验（以下简称监 检）： a) 压力容器由筒体和平盖、凸形封头（不包括球冠形封头），或者由两个凸形封头组成； b) 筒体、封头和接管等主要受压元件的材料为碳素钢、奥氏体不锈钢或者 Q345R； c) 设计压力小于或者等于 1.6 MPa； d) 容积小于或者等于 1 m3 ； e) 工作压力与容积的乘积小于或者等于 1 MPa·m3； f) 介质为空气、氮气、二氧化碳、惰性气体、医用蒸馏水蒸发而成的蒸气或者上述气（汽）体的 混合气体；允许介质中含有不足以改变介质特性的油等成分，并且不影响介质与材料的相容性； g) 设计温度大于或者等于 -20℃，最高工作温度小于或者等于 150℃； h) 非直接火焰加热的焊接压力容器（当内直径小于或者等于 550 mm 时允许采用平盖螺栓连接）。
Code for supervision and inspection of safety performance of simple pressure vessels
- ICS
- 23.020.10
- CCS
- J74
- 发布
- 2017-09-15
- 实施
- 2017-10-15
本标准规定了在用尿素合成塔的检验的准备、定期检验的内容和方法。 本标准适用于结构为多层包扎和整体包扎的尿素合成塔定期检验。
Regulations for periodic inspection of urea synthesis tower
- ICS
- 23.020.10
- CCS
- J74
- 发布
- 2017-09-15
- 实施
- 2017-10-15
GRP tanks and vessels for use above ground. Example calculation of a GRP-vessel
- ICS
- 23.020.10
- CCS
- 发布
- 2017-07-11
- 实施
- 2017-07-11
Vertical steel tanks with less than 1 000 litre capacity, for the above ground storage of liquids - Part 1: Singlewall
- ICS
- 23.020.10
- CCS
- A82;G93
- 发布
- 2017-06
- 实施
Vertical steel tanks with less than 1 000 litre capacity, for the above ground storage of liquids - Part 2: Doublewall
- ICS
- 23.020.10
- CCS
- A82;G93
- 发布
- 2017-06
- 实施
This Technical Report gives guidance for the design of a vessel using the standard EN 13121 3 GRP tanks and vessels for use above ground. The calculation is done according to the advanced design method given in EN 13121 3:2016, 7.9.3 with approved laminates and laminate properties.
GRP tanks and vessels for use above ground - Part 5: Example calculation of a GRP-vessel
- ICS
- 23.020.10
- CCS
- 发布
- 2017-05-31
- 实施
1.1 This specification covers design criteria requirements, design geometry, material characteristics, and desirable features for oil spill response boom slide connections. These criteria are intended to define minimum mating characteristics and are not intended to be restricted to a specific configuration. 1.2 The specification defines the geometry required to mate with typical Universal slide connectors or Specification F962 connectors with web thickness up to 0.3 in. Some very heavy-duty or PVC connectors may exceed this dimension and not be compatible. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Oil Spill Response Boom Connection: Slide Connector
- ICS
- 23.020.10
- CCS
- 发布
- 2017-05-01
- 实施
GRP tanks and vessels for use above ground - Part 5: Example calculation of a GRP-vessel
- ICS
- 23.020.10
- CCS
- 发布
- 2017-05-01
- 实施
5.1 General—This procedure is used for evaluation of the structural integrity of atmospheric storage tanks. The AE method can detect flaws which are in locations that are stressed during pressurization. Such locations include the tank wall, welds attaching pads to the tank, nozzle attachments, and welds attaching circumferential stiffeners to the tank. Among the potential sources of acoustic emission are: 5.1.1 In both parent metal and weld associated regions: 5.1.1.1 Cracks, 5.1.1.2 The effect of corrosion, including cracking of corrosion products or local yielding, 5.1.1.3 Stress corrosion cracking, 5.1.1.4 Certain physical changes, including yielding and dislocations, 5.1.1.5 Embrittlement, and 5.1.1.6 Pits and gouges. 5.1.2 In weld associated regions: 5.1.2.1 Incomplete fusion, 5.1.2.2 Lack of penetration, 5.1.2.3 Undercuts, and 5.1.2.4 Voids and porosity. 5.1.2.5 Inclusions: 5.1.2.6 Contamination. 5.1.3 In parent metal: 5.1.3.1 Laminations. 5.1.4 In brittle linings: 5.1.4.1 Cracks, 5.1.4.2 Chips, and 5.1.4.3 Inclusions. Note 1: Not all of these sources are typically encountered in field examination, some are detected under laboratory conditions. 5.2 Accuracy of the results from this practice can be influenced by factors related to setup and calibration of instrumentation, background noise, material properties and characteristics of an examined structure. 5.3 The outcome of this practice is t
Standard Practice for Examination of Liquid-Filled Atmospheric and Low-Pressure Metal Storage Tanks Using Acoustic Emission
- ICS
- 23.020.10
- CCS
- A84
- 发布
- 2017
- 实施
This Standard specifies minimum design and material requirements as well as manufacturing practices and markings for prefabricated septic tanks, sewage holding tanks, and effluent chambers made of steel, concrete, fibreglass-reinforced plastic (FRP), polyvinylchloride (PVC), polypropylene (PP), polyethylene (PE), or other thermoplastics that are designed to handle sewage or sewage effluent.
Design, material, and manufacturing requirements for prefabricated septic tanks and sewage holding tanks
- ICS
- 23.020.10
- CCS
- 发布
- 2016-12-01
- 实施
Steel manhole shafts for the underground tanks designed for the storage of flammable and non-flammable water polluting liquids
- ICS
- 23.020.10
- CCS
- G93;P94
- 发布
- 2016-11
- 实施
1.1 This guide covers information for evaluating tank systems for operational conformance with the Federal technical standards (including the financial responsibility requirements) for underground storage tanks (USTs) found at 40 Code of Federal Register (CFR) Part 280. 1.2 This guide does not address the corrective action requirements of 40 CFR Part 280. 1.3 To the extent that a tank system is excluded or deferred from the federal regulations under Subpart A of 40 CFR Part 280, it is not covered by this guide. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Guide for Performing Evaluations of Underground Storage Tank Systems for Operational Conformance with 40 CFR, Part 280 Regulations
- ICS
- 23.020.10
- CCS
- 发布
- 2016-10-01
- 实施
GRP tanks and vessels for use above ground - Part 3: Design and workmanship; German version EN 13121-3:2016
- ICS
- 23.020.10
- CCS
- P34
- 发布
- 2016-10
- 实施
Design requirements for wind load and seismic load of oil storage tanks
- ICS
- 23.020.10
- CCS
- 发布
- 2016-09-28
- 实施
Design requirements for wind load and seismic load of oil storage tanks
- ICS
- 23.020.10
- CCS
- 发布
- 2016-09-28
- 实施
Overfill prevention devices for static tanks for liquid fuels. Overfill prevention devices with closure device
- ICS
- 23.020.10
- CCS
- E98
- 发布
- 2016-07-31
- 实施
- 2016-07-31
Overfill prevention devices for static tanks for liquid fuels. Overfill prevention devices without a closure device
- ICS
- 23.020.10
- CCS
- E98
- 发布
- 2016-07-31
- 实施
- 2016-07-31
Workmanship of steel tanks for the storage of liquids - Factory production control
- ICS
- 23.020.10
- CCS
- 发布
- 2016-07
- 实施
