23.040.10 铁管和钢管 标准查询与下载
共找到 1225 条与 铁管和钢管 相关的标准，共 82 页
This document specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low tempe
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes; German version EN 10217-7:2021
- ICS
- 23.040.10
- CCS
- 发布
- 2021-06-00
- 实施
Austenitic, austenitic-ferritic and ferritic longitudinally welded stainless steel tubes for the food and chemical industry
- ICS
- 23.040.10
- CCS
- 发布
- 2021-06-00
- 实施
Welded steel tubes for pressure purposes. Technical delivery conditions. Stainless steel tubes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-14
- 实施
- 2021-05-14
Ultrasonic testing of steel plates for pressure vessels
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-11
- 实施
Eddy current examination of steel pipes and tubes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-11
- 实施
Ultrasonic testing of steel plates for pressure vessels
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-11
- 实施
本文件规定了内覆或衬里耐腐蚀合金复合钢管入场检验的检验项目、检验流程、检验方法、验收指标和验收报告的要求。 本文件适用于石油、天然气行业管道输送系统中内覆或衬里耐腐蚀合金复合钢管进入购方指定场地后的入场检验。
Entrance inspection for CRA clad or lined steel pipe
- ICS
- 23.040.10
- CCS
- B071
- 发布
- 2021-05-08
- 实施
- 2021-05-08
Ductile iron pipes, fittings and accessories -- Requirements and test methods for organic linings of ductile iron pipes and fittings -- Part 2: Thermoplastic Acid Modified Polyolefin (TMPO) lining of pipes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-06
- 实施
- 2021-05-06
Seamless steel tubes for pressure purposes. Technical delivery conditions. Stainless steel tubes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-05
- 实施
- 2021-05-05
1.1 This specification covers centrifugally cast ferritic/ austenitic steel pipe intended for general corrosive service. These steels are susceptible to embrittlement if used for prolonged periods at elevated temperatures. 1.2 Optional supplementary requirements are provided when additional testing may be required. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of each other. Combining values from the two systems may result in nonconformance with the specification. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Centrifugally Cast Ferritic/Austenitic Stainless Steel Pipe for Corrosive Environments
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-01
- 实施
Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-05-01
- 实施
Welded steel tubes for pressure purposes – Technical delivery conditions – Part 7: Stainless steel tubes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-04-29
- 实施
- 2021-04-29
Seamless steel tubes for pressure purposes – Technical delivery conditions – Part 5: Stainless steel tubes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-04-29
- 实施
- 2021-04-29
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Electric welded and submerged arc welded alloy fine grain steel tubes with specified room, elevated and low temperature properties
- ICS
- 23.040.10
- CCS
- 发布
- 2021-04-27
- 实施
- 2021-04-27
This document specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures. NOTE Once the reference of this document is published in the Official Journal of the European Union (OJEU) under Directive 2014/68/EU, pressure equipment directive, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 2014/68/EU is limited to technical data of materials in this document and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer of the pressure equipment, taking also into account the subsequent manufacturing processes which could affect properties of the base materials.
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes
- ICS
- 23.040.10
- CCS
- 发布
- 2021-04-21
- 实施
- 2021-07-31
Large diameter welded stainless steel pipes
- ICS
- 23.040.10
- CCS
- H48
- 发布
- 2021-04-20
- 实施
Automated flux leakage examination of steel pipes and tubes
- ICS
- 23.040.10
- CCS
- H26
- 发布
- 2021-04-20
- 实施
Automated eddy current examination of steel pipes and tubes
- ICS
- 23.040.10
- CCS
- H26
- 发布
- 2021-04-20
- 实施
Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties
- ICS
- 23.040.10
- CCS
- 发布
- 2021-04-07
- 实施
- 2021-04-07
