23.040.10 铁管和钢管 标准查询与下载

EC 1-2021 UNI EN 10217-1-2021 压力用途焊接钢管 交货技术条件 第1部分：具有规定室温性能的电焊和埋弧焊非合金钢管

Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Electric welded and submerged arc welded non-alloy steel tubes with specified room temperature properties

EN 10216-5:2021 压力用途无缝钢管.交货技术条件.第5部分:不锈钢管

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes

JIS G 0803:2021 焊接钢管焊缝的射线胶片检测

Radiographic examination with film for the weld seam of welded steel tubes

JIS G 0804:2021 焊接钢管焊缝的数字射线检测

Digital radiographic examination for the weld seam of welded steel tubes

NF E86-700-3/A1:2021 金属工业管道 第3部分：设计和计算

Metallic industrial piping - Part 3 : design and calculation

ASTM A796/A796M-21 波纹钢管 管拱和拱形结构设计的风险和卫生下水道及其他埋藏应用的标准实践

1.1?This practice covers the structural design of corrugated steel pipe and pipe-arches, ribbed and composite ribbed steel pipe, ribbed pipe with metallic-coated inserts, closed rib steel pipe, composite corrugated steel pipe, and steel structural plate pipe, pipe-arches, and un

Standard Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications

ASTM A803/A803M-16(2021) 无缝和焊接铁素体不锈钢给水加热管的标准规范

1.1 This specification covers seamless and welded ferritic stainless steel feedwater heater tubes including those bent, if specified, into the form of U-tubes for application in tubular feedwater heaters. 1.2 The tubing sizes covered shall be 5⁄8 to 1 in. [15.9 to 25.4 mm] inclusive outside diameter, and average or minimum wall thicknesses of 0.028 in. [0.7 mm] and heavier. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Seamless and Welded Ferritic Stainless Steel Feedwater Heater Tubes

ASTM A795/A795M-21 防火用黑色和热浸镀锌（镀锌）焊接无缝钢管的标准规范

1.1?This specification covers black and hot-dipped galvanized welded and seamless steel pipe in NPS 1/2 to NPS 10, inclusive [DN 15 to DN 250, inclusive] (Note 1), with wall thicknesses as given in Table 1 and Table 2. Pipe having other wall thicknesses may be furnished provided

Standard Specification for Black and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless Steel Pipe for Fire Protection Use

ASTM A554-21 焊接不锈钢机械管标准规范

1.1?This specification covers welded austenitic, ferritic, and austenitic-ferritic duplex stainless steel mechanical tubing intended for use in ornamental, structural, exhaust, and other applications where appearance, mechanical properties, or corrosion resistance is needed. The

Standard Specification for Welded Stainless Steel Mechanical Tubing

JIS G 3445:2021 机械结构用碳钢管

Carbon steel tubes for machine structure

JIS G 3441:2021 机械用途合金钢管

Alloy steel tubes for machine purposes

JIS G 3444:2021 通用结构用碳钢管

Carbon steel tubes for general structure

KS D ISO 4200-2021 焊接和无缝平端钢管.单位长度尺寸和质量通用表

Plain end steel tubes, welded and seamless —General tables of dimensions and masses per unit length

KS D ISO 4200:2021 焊接和无缝平端钢管.单位长度尺寸和质量通用表

Plain end steel tubes, welded and seamless —General tables of dimensions and masses per unit length

T/CSTM 00017.1-2021 电站用马氏体耐热钢08Cr9W3Co3VNbCuBN(G115) 第1部分：对焊管件

本部分规定了电站用马氏体耐热钢08Cr9W3Co3VNbCuBN(G115)对焊管件的术语和定义、订货内容、原材料要求、技术要求、制造、检验、缺陷处理、标志、表面防护、包装以及质量证明文件。   本部分适用于600℃以上电站锅炉和管道用马氏体耐热钢G115对焊管件，包括弯头、三通、异径管、接管座、封头等零部件，其它G115管件可参照执行。

Martensitic heat-resistant steel of 08Cr9W3Co3VNbCuBN(G115) for power station —Part 1：Butt-welding pipe fittings

PN-EN 14628-1-2021-01 E 球墨铸铁管、管件和附件 要求和试验方法 第1部分：PE 涂层

Ductile iron pipes, fittings and accessories -- Requirements and test methods -- Part 1: PE coatings

OENORM EN 15655-2-2021 球墨铸铁管、管件和附件 球墨铸铁管和管件有机衬里的要求和试验方法 第2部分：管道的热塑性酸改性聚烯烃（TMPO）衬里

Ductile iron pipes, fittings and accessories - Requirements and test methods for organic linings of ductile iron pipes and fittings - Part 2: Thermoplastic Acid Modified Polyolefin (TMPO) lining of pipes

GOST R 59496-2021 钢焊管 焊接接头的缺陷 术语和定义

Steel welded pipes. Defects of welded joints. Terms and definitions

ASTM C1879-21 管道和刚性管道隔热层上铝和不锈钢护套安装的标准规程

1.1?This practice covers recommended installation techniques for aluminum and stainless steel jacketing for thermal and acoustic pipe insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. This practice applies to materials m

Standard Practice for Installation of Aluminum and Stainless Steel Jacketing over Thermal Insulation on Pipe and Rigid Tubing

ASTM A618/A618M-21 热成型无缝高强度低合金结构管的标准规范

1.1 This specification covers grades of hot-formed welded and seamless high-strength low-alloy square, rectangular, round, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings and for general structural purposes. When the steel is used in welded construction, the welding procedure shall be suitable for the steel and the intended service. 1.2 Square and rectangular tubing is produced with flats of 1 in. to 16 in. [25 mm to 405 mm] and a specified wall thickness of 0.095 in. to 1.0 in. [2.5 mm to 25 mm]. Round tubing is produced with diameters of 1 in. to 48 in. [25 mm to 1220 mm] and a specified wall thickness of 0.095 in. to 2.50 in. [2.5 mm to 65 mm]. 1.3 This specification covers the following grades: Ia, Ib, II, III, IV, V, VI and VII. 1.4 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements. 1.5 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Hot-Formed Welded and Seamless High-Strength Low-Alloy Structural Tubing