29.035.20 塑料和橡胶绝缘材料 标准查询与下载

NB/T 10187-2019 水上光伏系统用浮体技术要求和测试方法

Technical requirements and test methods for floating bodies for floating photovoltaic systems

ASTM F1236-19 电气保护橡胶制品外观检验的标准指南

1.1 The purpose of this guide is to present methods and techniques for the visual inspection of electrical protective rubber products. This guide also includes descriptions and photographs of irregularities found in these products. NOTE 1—It is not the purpose of this guide to establish the acceptance level of any irregularity described herein. That shall be established by the standard for each product. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Visual Inspection of Electrical Protective Rubber Products

ASTM D1048-14(2019) 橡胶绝缘毯标准规格

Standard Specification for Rubber Insulating Blankets

ASTM D2655-19 额定电压为0至2000 V 90和#xb0的电线和电缆用交联聚乙烯绝缘的标准规范；C操作

1.1 This specification covers a crosslinked polyethylene insulation for electrical wires and cables in conductor sizes 14 AWG [2.08 mm2 ] and larger. The base polymer of this insulation consists substantially of polyethylene or a polyethylene copolymer. 1.2 This type of insulation is suitable for continuous use on power cables in wet and dry locations, for voltage ratings not exceeding 2000 V and at conductor temperatures not exceeding 90°C for normal operation. For copper conductors, the insulation can be applied over the uncoated metal. 1.3 Materials covered by this specification are not sunlight and weather resistant unless they are carbon black pigmented or contain an additive system designed for this protection. 1.4 In many instances the insulation cannot be tested unless it has been formed around a conductor. Therefore, tests are done on insulated wire in this standard solely to determine the relevant property of the insulation and not to test the conductor or completed cable. 1.5 Whenever two sets of values are presented, in different units, the values in the first set are the standard, while those in parentheses are for information only. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Crosslinked Polyethylene Insulation for Wire and Cable Rated 0 to 2000 V, 90°C Operation

ASTM D5213-19 电绝缘和电介质用聚合树脂薄膜的标准规范

1.1 This specification covers requirements for the material, dimensions and tolerances, and property values of film, in sheet or strip form, with or without heat-sealable coatings. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. NOTE 1—This document is similar to IEC 60674, Part 3, Sheets 2, 4, 5, 6, and 7. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polymeric Resin Film for Electrical Insulation and Dielectric Applications

ASTM D2686-19 聚四氟乙烯背衬压敏电绝缘带的标准规范

1.1 This specification covers electrical insulating tape consisting of a polytetrafluoroethylene (PTFE) film coated on one side with a pressure-sensitive adhesive. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. NOTE 1—This standard is similar to IEC 60454-3-14. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polytetrafluoroethylene-Backed Pressure-Sensitive Electrical Insulating Tape

IEC 60674-2:2016+AMD1:2019 CSV 电气用塑料薄膜规范第2部分:试验方法

Specification for plastic films for electrical purposes - Part 2: Methods of test

IEC 60674-2:2016/AMD1:2019 电气用塑料薄膜规范第2部分:试验方法

Specification for plastic films for electrical purposes - Part 2: Methods of test

IEC 60674-3-2:2019 电气用塑料薄膜规格 - 第3部分:各材料规格 - 第2页:平衡双轴取向聚对苯二甲酸乙二醇酯（宠物）用于电绝缘的要求

Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films

ASTM D178-19 橡胶绝缘垫的标准规范

1.1 This specification covers acceptance testing of rubber insulating matting for use as a floor covering for protection of workers. 1.2 Two types of matting, differing in chemical and physical characteristics, are provided and are designated as Type I and Type II matting. 1.3 The following safety hazards caveat applies only to the test method portion, Sections 17 to 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Rubber insulating matting should remain flexible for use through normal temperature ranges. NOTE 2—Rubber as used in this specification is a generic term that includes elastomers and elastomer compounds, regardless of origin. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rubber Insulating Matting

ASTM D2148-19 用于电绝缘的粘结硅橡胶胶带的标准测试方法

1.1 These test methods cover tests for bondable silicone rubber tapes which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing). 1.2 The methods appear in the following sections: Test Method Section Adhesion 3 – 10 Bond Strength 11 – 18 Dielectric Breakdown Voltage 19 – 26 Hardness 41 Length 33 and 34 Thickness 27 – 32 Width 36 – 40 1.3 Units—The values stated in SI units are the standard. The inch-pound units in parentheses are for information only. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement see 23.1.1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation

DIN IEC 60963 Berichtigung 1:2018 未使用的聚丁烯规范（IEC 60963:1988）；德版 HD 582 S1:1991；勘误表 1

Footnote c) was deleted in sheet 1, table 1. This also includes the remark in the line "water content" after the value of max. 60 and in the line "breakdown voltage" after the value of min. 40.

Specification for unused polybutenes (IEC 60963:1988); German version HD 582 S1:1991; Corrigendum 1

KS C IEC 60454-3-1-2018(2023) 电工用压敏胶带第3-1部分:单项材料规范带压敏粘合剂的聚氯乙烯薄膜带

Pressure-sensitive adhesive tapes for electrical purposes — Part 3-1: Specifications for individual materials — PVC film tapes with pressure-sensitive adhesive

KS C IEC 60454-3-1:2018 用于电气用途的压敏胶带 - 第3-1部分:各种材料的规格 - 带有压敏胶的Pvc胶带

Pressure-sensitive adhesive tapes for electrical purposes — Part 3-1: Specifications for individual materials — PVC film tapes with pressure-sensitive adhesive

KS C IEC 60454-3-1-2018 用于电气用途的压敏胶带 - 第3-1部分:各种材料的规格 - 带有压敏胶的Pvc胶带

Pressure-sensitive adhesive tapes for electrical purposes — Part 3-1: Specifications for individual materials — PVC film tapes with pressure-sensitive adhesive

ASTM D3555-07(2018) 90°电线电缆用耐轨道黑色交联聚乙烯绝缘的标准规范；C操作

Standard Specification for Track-Resistant Black Crosslinked Polyethylene Insulation for Wire and Cable, 90 °C Operation

ASTM D3554-07(2018) 电线和电缆用耐轨道黑色热塑性高密度聚乙烯绝缘的标准规范 75°；C操作

Standard Specification for Track-Resistant Black Thermoplastic High-Density Polyethylene Insulation for Wire and Cable, 75 °C Operation

ASTM D2148-18 用于电绝缘的粘结硅橡胶胶带的标准测试方法

Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation

ASTM F1837M-97(2018) 热缩电缆入口密封件的标准规范（米制）

1.1 This specification covers the general requirements for heat-shrink cable entry seals. Cable entry seals are intended for making electrical cable penetrations into connection boxes, bulkheads, or other enclosures. These devices are suitable for both thin wall enclosures up to 5 mm (3⁄16 in.) thick and thick-wall enclosures of 5 mm to 19 mm (3⁄16 in. to 3⁄4 in.) thick. 1.2 Cable entry seals shall have factory-applied adhesive that provides the seal to wire and cable jackets. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Heat-Shrink Cable Entry Seals (Metric)

ASTM F1236-18 电气保护橡胶制品外观检验的标准指南

Standard Guide for Visual Inspection of Electrical Protective Rubber Products