29.080.20 套管 标准查询与下载

IEC 60137:2003 交流电压1000V以上的绝缘套管

Specifies the characteristics and tests for insulated bushings intended for use in electrical apparatus, machinery, transformers, switchgear and installations for three-phase alternating current systems, having highest voltage for equipment above 1 000 V

Insulated bushings for alternating voltages above 1000 V

BS EN 50386:2003 充液变压器用1KV以下和250A至5KA的套管

Bushings up to 1 kV and from 250 A to 5 kA, for liquid filled transformers

BS EN 50387:2003 充液变压器用1KV以下和125A至5KA的母线套管

This standard is applicable to moulded indoor busbar bushings for rated voltages up to 1 000 V, rated currents from 1 250 A up to 5 000 A and frequencies from 15 Hz up to 60 Hz for insulating liquid filled transformers. NOTE These bushings are suitable for operation at 1,1 kV in compliance with HD 428.1 S1.

Busbar bushings up to 1 kV and from 1,25 kA to 5 kA, for liquid filled transformers

BS EN 50386:2002 充液变压器用1KV以下和250A至5KA的套管

This standard is applicable to ceramic insulated bushings for rated voltages up to 1 000 V, rated currents from 250 A up to 5 000 A and frequencies from 15 Hz up to 60 Hz for insulating liquid filled transformers. NOTE These bushings are suitable for operation at 1,1 kV in compliance with HD 428.1 S1.

Bushings up to 1 kV and from 250 A to 5 kA, for liquid filled transformers

KS C 3904-2003(2018) 配线线路用聚合物轴套

Polymer bushing for wiring lines

KS C 3904-2003 配电线路用聚合物衬套

이 규격은 60Hz 교류 배전 계통에 사용하는 전력용 변압기, 계기용 변성기, 리엑터,

Polymer bushing for distribution lines

KS C 3904-2003(2023) 配电线路用聚合物套管

Polymer bushing for distribution lines

DS/IEC/TR 61464+Corr.1:2003 绝缘套管 套管中溶解气体分析（DGA）的解释指南，其中油是主要绝缘的浸渍介质（通常为纸）

This technical report gives guidance for the interpretation of dissolved gas analysis (DGA) which has been developed for bushings, in service, where the main insulation (generally paper) is impregnated with mineral insulating oil according to IEC 60296. This technical report is applicable to oil-filled and impregnated paper bushings in service. Until further experience has been gained, the methods should be applied with caution in relation to other materials, e.g. synthetic hydrocarbons based on dodecylbenzene, according to IEC 60867. The indication obtained by the interpretation of a dissolved gas analysis of an oil sample taken out of a bushing should be

Insulated bushings - Guide for the interpretation of dissolved gas analysis (DGA) in bushings where oil is the impregnating medium of the main insulation (generally paper)

DIN EN 50243:2003 充液体变压器用 24 kV、36 kV、5 kA 和 8 kA 的户外套管; 德文版本 EN 50243:2002

This standard is applicable to ceramic insulated outdoor bushings for rated voltages of 24 kV and 36 kV, with rated currents of 5 kA and 8 kA and frequencies from 15 Hz up to 60 Hz for insulating liquid filled transformers. It establishes dimensions, to ensure interchangeability mounting of bushings. Two types of construction are specified, type A and type B, both types for rated voltages 24 kV and 36 kV and rated currents of 5 kA and 8 kA.

Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformers; German version EN 50243:2002

IEC TR2 61464/COR1:2003 绝缘套管.油作为主绝缘(普通纸)浸渍介质的套管中溶解气体分析(DGA)的说明指南

This standard is Insulated bushings - Guide for the interpretation of dissolved gas analysis (DGA) in bushings where oil is the impregnating medium of the main insulation (generally paper); Corrigendum 1.

Insulated bushings - Guide for the interpretation of dissolved gas analysis (DGA) in bushings where oil is the impregnating medium of the main insulation (generally paper)

DIN EN 50336:2002 不超过36kV的变压器和电抗器电缆箱用套管; 德文版本 EN 50336:2002

The document is applicable to insulated bushings for use in air insulated, shroud insulated and fully insulated cable boxes for liquid filled transformers and reactors for rated voltages up to 36 kV, and rated currents up to 4000 A at frequencies from 15 Hz to 60 Hz.

Bushings for transformer and reactor cable boxes not exceeding 36 kV; German version EN 50336:2002

BS EN 50336:2002 不超过36kV的变压器和电抗器电缆盒用套管

This standard is applicable to insulated bushings for use in air insulated, shroud insulated and fully insulated cable boxes for liquid filled transformers and reactors for rated voltages up to 36 kV, and rated currents up to 4 000 A at frequencies from 15 Hz to 60 Hz.

Bushings for transformers and reactor cable boxes not exceeding 36 kV

DS/EN 50243:2002 用于 24 kV 和 36 kV 以及 5 kA 和 8 kA 的户外套管，用于充液变压器

This standard is applicable to ceramic insulated outdoor bushings for highest voltages for equipment of 24 kV and 36 kV, with rated currents of 5 kA and 8 kA and frequencies from 15 Hz up to 60 Hz for insulating liquid filled transformers. This standard establishes dimensions to ensure interchangeability and adequate mounting of bushings. Two types of construction are specified, type A and type B, both types for highest voltages for equipment 24 kV and 36 kV and rated currents of 5 kA and 8 kA. The mechanical stresses of the conductor tube make the difference between type A and type B. The conductor tube of type A is axially and radially fixed in the top of

Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformers

DS/EN 50336:2002 不超过 36 kV 的变压器和电抗器电缆箱用套管

This standard is applicable to insulated bushings for use in air insulated, shroud insulated and fully insulated cable boxes for liquid filled transformers and reactors for rated voltages up to 36 kV, and rated currents up to 4000 A at frequencies from 15 Hz to 60 Hz.

Bushings for transformers and reactor cable boxes not exceeding 36 kV

LST EN 50262+AC-2001/A1-2002 用于电气安装的公制电缆密封套

Metric cable glands for electrical installations

BS EN 50243:2002 充液变压器用 24 kV、36 kV、5 kA 和 8 kA 的户外套管

This standard is applicable to ceramic insulated outdoor bushings for highest voltages for equipment of 24 kV and 36 kV, with rated currents of 5 kA and 8 kA and frequencies from 15 Hz up to 60 Hz for insulating liquid filled transformers. This standard establishes dimensions to ensure interchangeability and adequate mounting of bushings. Two types of construction are specified, type A and type B, both types for highest voltages for equipment 24 kV and 36 kV and rated currents of 5 kA and 8 kA. The mechanical stresses of the conductor tube make the difference between type A and type B. The conductor tube of type A is axially and radially fixed in the top of the bushing. The inner line terminal of the transformer can be flexible and without any special support for the lower end of the conductor tube. In case of type B, the conductor tube is only radially fixed in the top of the bushing. In that case, a rigid support has to be mounted to fix the lower end of the conductor tube (for example, in combination with a drip proofed sealing end). The drip proofed sealing end is often required in the service requirements. In this case, it is not possible to use type A because of the existing double fixation. Therefore, both bushing types A and B have to be specified. The condition for the usage of type B is that the drip prooved sealing end is able to withstand the mechanical stress in axial direction.

Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformers

NF C68-302/A1:2001 电气设备用公制电缆密封垫

Metric cable glands for electrical installations.

DIN EN 50180 Bb.2:2001 充油变压器用1kV-36kV及250A-3.15kA衬套.结构紧固件

Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformers - Constructional details of fastening

DS/IEC/TS 61463:2001 套管 抗震鉴定

This technical report is applicable to alternating current and direct current bushings for rated voltages above 52 kV, mounted on transformers, other apparatus or buildings. It is accepted that for bushings for rated voltages less than or equal to 52 kV, due to their characteristics (resonance frequency greater than 25 Hz) seismic qualification is not required. This technical specification presents acceptable seismic qualification methods and requirements to demonstrate that a bushing can maintain its mechanical properties, insulate and carry current during and after an earthquake. The seismic qualification of a bushing is only performed upon request.

Bushings - Seismic qualification

LST EN 50262+AC-2001 用于电气安装的公制电缆密封套

Metric cable glands for electrical installations