29.080.20 套管 标准查询与下载

SANS 1037:2001 标准变压器轴衬

This specification covers insulated bushings for use on transformers in which the hollow insulators of the bushings provide the major insulation to voltage stresses. The bushings are designed for use with one or both ends immersed in an insulating medium (such as oil) or in air at the prevailing atmospheric pressure. NOTE a) The standards referred to in the specification are listed in appendix A. b) Requirements that must be specified by the purchaser are listed in appendix B. c) Except under the certification mark scheme, provision of the sample material required for the test given in 7.2 shall, when appropriate, be a matter for agreement between the supplier and the purchaser. d) Information regarding the verification of the quality of standard transformer bushings produced to this specification and a sampling plan that could be used to assess compliance with the specification of a lot of standard transformer bushing are given in appendix C.

Standard transformer bushings

IEC TS 61463:2000 套管 抗地震能力

This technical specification is applicable to alternating current and direct current bushings for rated voltages above 52 kV, mounted on transformers, other apparatus or buildings. It is accepted that for bushings for rated voltages less than or equal to 52 kV, due to their characteristics (resonance frequency greater than 25 Hz) seismic qualification is not required. This technical specification presents acceptable seismic qualification methods and require-ments to demonstrate that a bushing can maintain its mechanical properties, insulate and carry current during and after an earthquake. The seismic qualification of a bushing is only performed upon request.

Bushings - Seismic qualification

IEC TS 61463:1996/AMD1:2000 修改件1-套管-抗震鉴定

Amendment 1 - Bushings - Seismic qualification

IEEE Std C57.19.01-2000 户外器具轴衬的特性和尺寸

Electrical, dimensional, and related requirements for outdoor power apparatus bushings that have basic impulse insultion levels (BILs) of 200 kV and above are covered.

Characteristics and dimensions for outdoor apparatus bushings

ANSI/IEEE C57.19.01:2000 户外器具轴衬性能特征和尺寸

Electrical, dimensional, and related requirements for outdoor power apparatus bushings that have basic impulse insultion levels (BILs) of 200 kV and above are covered.

Standard Performance Characteristics and Dimensions for Outdoor Apparatus Bushings

BS EN 50262:1999 电气设备用米制电缆密封装置

Requirements and tests for the construction and performance of complete metric cable glands, as supplied by the manufacturer or supplier. Does not include parts of cable glands.

Cable glands for electrical installations

NF C68-302:1999 电气设备的公制电缆密封垫

Metric cable glands for electrical installations.

BS EN 50180:1999 充液变压器用大于1kV但可达36kV和范围为250A至3.15kA的套管

This standard is applicable to ceramic and resin insulated bushings for rated voltages above 1 kV up to 36 kV, rated currents from 250 A up to 3 150 A and frequencies from 15 Hz up to 60 Hz for insulating liquid filled transformers. This standard establishes essential dimensions, to ensure interchangeability of bushings and to ensure adequate mounting and interchangeability of mating plug-in separable connectors of equivalent ratings.

Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformers

BS EN 50181:1999 不包括液体填充变压器在内的设备用大于1KV和达36KV范围为250A到1.25KA的插入型套管

This standard is applicable to insulated bushings for rated voltages above 1 kV up to 36 kV, rated currents from 250 A up to 1 250 A and frequencies from 15 Hz up to 60 Hz for equipment other than liquid filled transformers. This standard establishes essential dimensions, to ensure adequate mounting and interchangeability of mating plug-in separable connectors of equivalent ratings.

Plug-in type bushings above 1 kV up to 36 kV and from 250 A to 1.25 kA for equipment other than liquid filled transformers

JG/T 3053-1998 可挠金属电线保护套管

本标准规定了可挠金属电线保护套管的分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存等。 本标准适用于可挠金属电线保护套管。

Flexible metal conduits

DIN EN 50180:1998 已充装液体的变压器用1kV以上至36kV和250A至3,15kA的套管

The document is applicable to ceramic and resin insulated bushings for rated voltages above 1 kV up to 36 kV, rated currents from 250 A to 3150 A and frequencies from 15 Hz up to 60 Hz for insulating liquid filled transformers.#,,#

Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformers; German version EN 50180:1997 + Corrigendum 1998

IEC TR2 61464:1998 绝缘套管 油作为主绝缘(普通纸)浸渍介质的套管中溶解气体分析(DGA)的说明指南

This technical report gives guidance for the interpretation of dissolved gas analysis (DGA) which has been developed for bushings, in service, where the main insulation (generally paper) is impregnated with mineral insulating oil according to IEC 60296. This technical report is applicable to oil-filled and impregnated paper bushings in service. Until further experience has been gained, the methods should be applied with caution in relation to other materials, e.g. synthetic hydrocarbons based on dodecylbenzene, according to IEC 60867. The indication obtained by the interpretation of a dissolved gas analysis of an oil sample taken out of a bushing should be viewed as a guide and any resulting action should be undertaken with proper engineering judgement.

Insulated bushings - Guide for the interpretation of dissolved gas analysis (DGA) in bushings where oil is the impregnating medium of the main insulation (generally paper)

NF C66-554:1997 充液变压器用电压大于 1 kV 并可达 36 kV 和电流 250 A 至 3.15 kA 的套管

Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformers.

NF C66-556:1997 充液变压器除外的设备用电压大于 1 kV 并可达 36 kV 和电流 250 A 至 1.25 kA 的套管

Plug-in type bushings above 1 kV up to 36 kV and from 250 A to 1,25 kA for equipment other than liquid filled transformers.

NF C66-522:1996 电压为1000V以下及电流从1.25kA～5kA的充油变压器汇流条套管

Busbar bushings up to 1 kV and from 1,25 kA to 5 k, for liquid filled transformers.

NF C66-511:1996 电压为1000V以下及电流从250A～5kA的充油变压器套管

Buschings up to 1 kV and from 250 A to 5 kA, for liquid filled transfomers.

IEC TS 61463:1996 套管-抗震鉴定

Bushings - Seismic qualification

CNS 5518-1996 铜线用祼压接套筒

本标准适用于以软铜绞线或单线电线连接机器相互间之配线，使用 CNS 5417 〔屋内配线用电线连接工具〕规定之连接工具或压接套筒制造厂所指定之连接工具（以下简称工具）（1），将导线相互压着连接之裸压接套筒（以下简称套筒）。注（1）：直线对接用套筒及直线重迭压接用套筒

Non-insulated Crimp-type Sleeves for Copper Conductors

NF C66-550:1996 交流电压大于 1 kV 的绝缘套管

Insulated bushings for alternating voltages above 1 kv.

ANSI/IEEE C57.19.03:1996 直流装置用套管的标准要求、术语和试验规程

Applies to outdoor and indoor power apparatus dc bushings of condenser type that have basic impulse insulation levels of 110 kV and above for use as components of oil-filled converter transformers and smoothing reactors, as well as air-to-air dc bushings.

Standard Requirements, Terminology and Test Code for Bushings for DC Applications