29.080.30 绝缘系统 标准查询与下载
共找到 364 条与 绝缘系统 相关的标准，共 25 页
Evaluation and qualification of electrical insulation systems (IEC 60505:2011)
- ICS
- 29.080.30
- CCS
- 发布
- 2011-12-30
- 实施
- 2011-12-30
This International Standard establishes the basis for estimating the ageing of electrical insulation systems (EIS) under conditions of either electrical, thermal, mechanical, environmental stresses or combinations of these (multifactor stresses).It specifies the principles and procedures that shall be followed, during the development of EIS functional test and evaluation procedures, to establish the estimated service life for a specific EIS.This standard should be used by all IEC technical committees responsible for equipment having an EIS.
Evaluation and qualification of electrical insulation systems
- ICS
- 29.080.30
- CCS
- 发布
- 2011-10-17
- 实施
- 2011-10-17
IEC 60664-3:2003+A1:2010 applies to assemblies protected against pollution by the use of coating, potting or moulding, thus allowing a reduction of clearance and creepage distances as described in Part 1 or Part 5. This standard describes the requirements and test procedures for two methods of protection: - type 1 protection improves the microenvironment of the parts under the protection; - type 2 protection is considered to be similar to solid insulation. This standard also applies to all kinds of protected printed boards, including the surface of inner layers of multi-layer boards, substrates and similarly protected assemblies. In the case of multi-layer printed boards, the distances through an inner layer are covered by the requirements for solid insulation in Part 1. This standard refers only to permanent protection. It does not cover assemblies that are subjected to mechanical adjustment or repair. The principles of this standard are applicable to functional, basic, supplementary and reinforced insulation. This consolidated version consists of the second edition (2003) and its amendment 1 (2010). Therefore, no need to order amendment in addition to this publication. The contents of the corrigendum of November 2010 have been included in this copy.
Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
- ICS
- 29.080.30
- CCS
- 发布
- 2011-10-12
- 实施
Insulation coordination for equipment within low-voltage systems - Part 2-1: Application guide - Explanation of application of the IEC 60664 series, dimensioning examples and dielectric testing; Corrigendum 1
- ICS
- 29.080.30
- CCS
- K30
- 发布
- 2011-10
- 实施
Evaluation and qualification of electrical insulation systems
- ICS
- 29.080.30
- CCS
- K04
- 发布
- 2011-09-30
- 实施
- 2011-09-30
IEC 60505:2011 establishes the basis for estimating the ageing of electrical insulation systems (EIS) under conditions of either electrical, thermal, mechanical, environmental stresses or combinations of these (multifactor stresses). It specifies the principles and procedures that shall be followed, during the development of EIS functional test and evaluation procedures, to establish the estimated service life for a specific EIS. This standard should be used by all IEC technical committees responsible for equipment having an EIS. The main change with respect to the previous edition is that Annex A: Glossary is now available in an Internet version as well as a hardcopy version. The internet version contains an abridged text version and a multimedia supplement.
Evaluation and qualification of electrical insulation systems
- ICS
- 29.080.30
- CCS
- 发布
- 2011-08-26
- 实施
- 2011-11-15 (7)
Evaluation and qualification of electrical insulation systems
- ICS
- 29.080.30
- CCS
- K15
- 发布
- 2011-07
- 实施
Electrical insulation systems (EIS). Thermal evaluation of combined liquid and solid components. General requirements
- ICS
- 29.080.30
- CCS
- K15
- 发布
- 2011-06-30
- 实施
- 2011-06-30
1 Scope This part of IEC/TS 62332 is applicable to EIS containing solid and liquid components where the thermal stress is the dominant ageing factor, without restriction to voltage class. This part specifies a dual-temperature test procedure for the thermal evaluation and qualification of electrical insulation systems ( EIS ).
Electrical insulation systems (EIS). Thermal evaluation of combined liquid and solid components - General requirements
- ICS
- 29.080.30
- CCS
- 发布
- 2011-06-30
- 实施
- 2011-06-30
This part of IEC/TS 62332 is applicable to EIS containing solid and liquid components where the thermal stress is the dominant ageing factor, without restriction to voltage class.This part specifies a dual-temperature for the thermal evaluation and qualification of electrical insulation systems (EIS).
Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 1: General requirements
- ICS
- 29.080.30
- CCS
- 发布
- 2011-05-29
- 实施
- 2011-05-29
Insulation co-ordination - Part 1: Definitions, principles and rules
- ICS
- 29.080.30
- CCS
- 发布
- 2011-03-30
- 实施
Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 1: General requirements
- ICS
- 29.080.30
- CCS
- K04
- 发布
- 2011-03
- 实施
Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution (IEC 60664-3:2003 + A1:2010); German version EN 60664-3:2003 + A1:2010, Corrigendum to DIN EN 60664-3 (VDE 0110
- ICS
- 29.080.30
- CCS
- K31
- 发布
- 2011-03
- 实施
This part of IEC 60664, which is a technical report, serves as an application guide for technical committees and manufacturers specifying dimensioning requirements for products in accordance with the IEC 60664 series. The significant items for consideration are as follows: a) nominal system voltage(s) or rated insulation voltage(s); b) overvoltage category of the products (OV cat.); c) any type of overvoltages; d) frequency of the voltage; e) characteristics of the solid insulating material; f) pollution degree and humidity levels.
Insulation coordination for equipment within low-voltage systems - Part 2-1: Application guide - Explanation of application of the IEC 60664 series, dimensioning examples and dielectric testing
- ICS
- 29.080.30
- CCS
- K30
- 发布
- 2011-01-01
- 实施
- 2011-01-01
Insulation coordination for equipment within low-voltage systems - Part 3 : use of coating, potting or moulding for protection against pollution.
- ICS
- 29.080.30
- CCS
- K15
- 发布
- 2011-01-01
- 实施
- 2011-01-01
Insulation coordination for equipment within low-voltage systems -- Part 3: Use of coating, potting or moulding for protection against pollution (IEC 60664-3:2003/A1:2010)
- ICS
- 29.080.30
- CCS
- 发布
- 2010-11-30
- 实施
- 2010-11-30
Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
- ICS
- 29.080.30
- CCS
- K30
- 发布
- 2010-11
- 实施
Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution (IEC 60664-3:2003 + A1:2010); German version EN 60664-3:2003 + A1:2010
- ICS
- 29.080.30
- CCS
- K30
- 发布
- 2010-10
- 实施
- 2010-10-01
Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
- ICS
- 29.080.30
- CCS
- 发布
- 2010-08-23
- 实施
This part of IEC 60664 applies to assemblies protected against pollution by the use of coating, potting or moulding, thus allowing a reduction of clearance and creepage distances as described in Part 1 or Part 5. This standard describes the requirements and test procedures for two methods of protection: – type 1 protection improves the microenvironment of the parts under the protection; – type 2 protection is considered to be similar to solid insulation. This standard also applies to all kinds of protected printed boards, including the surface of inner layers of multi-layer boards, substrates and similarly protected assemblies. In the case of multi-layer printed boards, the distances through an inner layer are covered by the requirements for solid insulation in Part 1. This standard refers only to permanent protection. It does not cover assemblies that are subjected to mechanical adjustment or repair. The principles of this standard are applicable to functional, basic, supplementary and reinforced insulation.
BASIC SAFETY PUBLICATION Insulation coordination for equipment within low-voltage systems – Part 3: Use of coating, potting or moulding for protection against pollution
- ICS
- 29.080.30
- CCS
- K04;A19
- 发布
- 2010-08-01
- 实施
- 2010-08-01
