29.160.20 发电机 标准查询与下载

DL/T 294.2-2011 发电机灭磁及转子过电压保护装置技术条件 第2部分：非线性电阻

本标准规定了同步发电机灭磁及转子过电压保护装置用非线性电阻的基本技术要求、使用的术语、定义、计算方法、试验、技术文件等。 本标准适用于单片标称容量为10kJ及以上的非线性电阻阀片及组件，应用于发电机灭磁及转子过电压保护装置非线性电阻的使用与订货要求。

Specification for equipment of de-excitation and over voltage protection for generators. Part 2:Non-linear resistor

DL/T 298-2011 发电机定子绕组端部电晕检测与评定导则

本标准规定了使用日盲型紫外成像装置和暗室目测法对发电机定子绕组端部进行电晕检测的方法和评定的标准。 本标准适用于定子额定电压在10.5KV及以上的发电机。 其他旋转电机也可参照执行。

Guide for detection and evaluation of corona defects on stator winding overhangs of generator

DL/T 331-2010 发电机与电网规划设计关键参数配合导则

本标准规定了发电机接入电网的设计原则及主要设备关键参数配合的技术要求。 本标准适用于220kV及以上的电力系统和新建容量在100MW及以上的汽轮发电机、50MW及以上水轮发电机设备的参数选用。100MW及以上燃气发电机和抽水蓄能机组可参照执行。

Guide of the key parameter coordination for planning and design of generator and power network

ANSI/UL 1004-4-2011 发电机安全标准

The revision proposes an exception to the generator overspeed test.

Standard for Safety for Electric Generators

IEC 114/56/CD:2010 IEC/TS 62600-200:海洋能.波浪,潮汐和其他水能转换器.第200部分:电力生产的潮汐能量变换器的功率性能评价

IEC/TS 62600-200: Marine energy - Wave, tidal and other water current converters - Part 200: Power performance assessment of electricity producing tidal energy converters

DIN EN 60034-22:2010 旋转电机.第22部分:往复式内燃机(RIC)驱动的发电机组用交流发电机(IEC 60034-22-2009).德文版本EN 60034-22-2009

Rotating electrical machines - Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets (IEC 60034-22:2009); German version EN 60034-22:2009

NF C51-222*NF EN 60034-22:2010 旋转电机.第22部分:往复式内燃机驱动的发电机组(RIC)用交流电发电机

Rotating electrical machines - Part 22 : AC generators for reciprocating internal combustion (RIC) engine driven generating sets.

BS EN 60034-22:2010 旋转电机 往复式内燃机驱动的发电机组用交流发电机

Rotating electrical machines. AC generators for reciprocating internal combustion (RIC) engine driven generating sets

BS EN 60034-22:2009 旋转电机.往复式内燃机驱动的发电机组用交流发电机

This part of IEC 60034 establishes the principal characteristics of a.c. generators under the control of their voltage regulators when used for reciprocating internal combustion (RIC) engine driven generating set applications and supplements the requirements given in IEC 60034-1. It covers the use of such generators for land and marine use, but excludes generating sets used on aircraft or used to propel land vehicles and locomotives.

Rotating electrical machines - AC generators for reciprocating internal combustion (RIC) engine driven generating sets

DS/EN 60034-22:2010 旋转电机 第22部分：用于往复式内燃机（RIC）发动机驱动的发电机组的交流发电机

IEC 60034-22:2009 establishes the principal characteristics of a.c. generators under the control of their voltage regulators when used for reciprocating internal combustion engine driven generating set applications and supplements the requirements given in IEC 60034-1. It covers the use of such generators for land and marine use, but excludes generating sets used on aircraft or used to propel land vehicles and locomotives. The most important changes with respect to the previous edition are: - technical changes to many definitions; - revision of table 1 and of the annex.

Rotating electrical machines - Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets

IEC 60034-22:2009 旋转电机.第22部分:往复式内燃机驱动的发电机组用交流发电机

This part of IEC 60034 establishes the principal characteristics of a.c. generators under the control of their voltage regulators when used for reciprocating internal combustion (RIC) engine driven generating set applications and supplements the requirements given in IEC 60034-1. It covers the use of such generators for land and marine use@ but excludes generating sets used on aircraft or used to propel land vehicles and locomotives. NOTE 1 For some specific applications (e.g. essential hospital supplies@ high-rise buildings@ etc.) supplementary requirements may be necessary. The provisions of this standard should be regarded as a basis for such requirements. NOTE 2 Attention is drawn to the need to take note of additional regulations or requirements imposed by various regulatory bodies. Such regulations or requirements may form the subject of agreement between the customer and the manufacturer when conditions of use of the end product invoke such requirements. NOTE 3 Examples of regulatory authorities: ? classification societies@ for generating sets used on ships and offshore installations; ? government agencies; ? inspection agencies@ local utilities@ etc. Annex A discusses the behaviour of generators covered by this standard when subjected to sudden load changes.

Rotating electrical machines - Part 22: AC generators for reciprocating internal combustion (RIC) engine driven generating sets

DL/T 1110-2009 卧式蒸发冷却电机基本技术条件

本标准规定了采用蒸发冷却的卧式电机的技术条件。 本标准适用于冷却方式采用蒸发冷却的卧式电机,包括发电机、电动机和作为调相机使用的电机。

Fundamental technical specifications for evaporative cooling horizontal electrical machinery

DL/T 5420-2009 水轮发电机定子现场装配工艺导则

本标准规定了单机容量在15MW及以上的水轮发电机定子现场装配的工艺方法、技术要求、操作（施工）程序和检验标准，适用于水轮发电机定子在电站现场进行的机座组焊、整体叠装铁心并完成全部线圈嵌线工作的装配。本标准不适用于分瓣定子现场组装或在发电机设备制造工组装并整体运输至现场的定子装配工艺。 本标准所指的水轮发电机定子是指常规全空冷水轮发电机定子、内冷却水轮发电机定子、灯泡贯流式水轮发电机定子以及抽水蓄能电站可逆式发电电动机定子。 单机容量小于15MW的水轮发电机定子的现场装配工艺要求可参照本标准的相应规定执行。

Technological guide for stator assembly in site of hydro-generators

DL/T 5230-2009 水轮发电机转子现场装配工艺导则

本标准规定了单机容量在15MW及以上的水轮发电机转子现场装配的工艺方法、技术要求、操作（施工）程序和检验标准，适用于磁轭为叠片式结构的水轮发电机转子在水电站现场的装配。本标准不适用于在发电机制造厂组装并整体运输至现场的转子装配工艺。 本标准所指的水轮发电机转子系指常规水轮发电机转子、灯泡贯流式水轮发电机转子及可逆式抽水蓄能发电电动机转子。 小型水轮发电机转子的现场装配工艺要求可参照本标准的相应规定执行。

Technological guide for rotor assembly in site of hydro-generators

DIN EN 60034-3:2009 旋转电机 第3部分:蒸汽涡轮或燃气涡轮驱动的同步发电机用专门要求

Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines (IEC 60034-3:2007); German version EN 60034-3:2008

SAE J1444-2009 小型发动机驱动发电机组的瞬时反应评估程序

The scope of this SAE Recommended Practice is to provide a uniform practice for the testing of small engine powered alternating current generator sets. This document is limited to reciprocating piston engines of less than 14.9 kw (20 BHP).

Procedure for Evaluating Transient Response of Small Engine Driven Generator Sets

GOST R 53471-2009 功率为100kW以上的同步三相发电机.通用规范

Synchronous three-phase generators of power above 100 kW. General specifications

IEEE 1665-2009 50和60Hz、额定电压1MVA及以上同步发电机的反绕用指南

Guide for the rewind of synchronous generators, 50 Hz and 60 Hz, rated 1 MVA and above

ANSI/IEEE 1665:2009 50和60Hz、额定电压1MVA及以上同步发电机的反绕用指南

The general parameters for this Guide apply to 50 or 60 hertz synchronous generators driven by reciprocating engines, steam turbines, combustion turbines, and hydro turbines. The guide generally applies to the stator and rotor of generators with rated outputs of 1 MVA and above.

Guide for the Rewind of Synchronous Generators, 50 and 60 Hz, Rated 1 MVA and Above

KS C IEC 60034-3-2008(2023) 旋转电机第3部分:蒸汽轮机或燃气轮机驱动的同步发电机的特殊要求

Rotating electrical machines－Part 3：Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines