29.160.20 发电机 标准查询与下载

DB65/T 2221-2005 并网失速型风力发电机组的检修与验收标准

Maintenance and acceptance standard of gird cinnected stall regulation wand turbine generator system

JB/T 6229-2005 透平发电机转子气体内冷通风道检验方法及限值

本标准规定了透平发电机转子在通风道外加一定风压的情况下，气体内冷通风道的检验方法及通风道内应达到的等效风速限值。 本标准适用于国内电机制造厂生产的气隙取气或槽底副槽通风的转子通风道的检验；也适用于国内电厂在安装交接和大修时，对转子通风道的检验。

Methods and limits for checking the direct gas ventilation cooling system of turbogenerator rotor

JB/T 6228-2005 汽轮发电机绕组内部水系统检验方法及评定

本标准规定了汽轮发电机水冷绕组内部水系统密封性和流通性的检验项目、方法及质量评定的要求。 本标准适用于水冷却的汽轮发电机制造过程的检验，也适用于机组的交接验收及大修过程的检验。

Checking methods and evaluation of water circuit within the winding of turbo generator

DL/T 5113.11-2005 水电水利基本建设工程.单元工程质量等级评定标准.第11部分:灯泡贯流式水轮发电机组安装工程

本标准规定了水电水利基本建设工程中灯泡贯流式水轮发电机组及附属设备单元工程安装质量等级评定办法。 本标准适用于单机容量2MW及以上和转轮直径25m及以上的灯泡贯流式水轮发电机组的工程质量等级评定。其他类型的贯流式水轮发电机组，以及单机容量小于2MW和转轮直径小于25m的灯泡贯流式水轮发电机组可参照执行。

Quality degree evaluate standard of unit engineering for hydropower and water conservancy construction engineering Part 11: Bulb turbine and generator units installation engineering

JB/T 10499-2005 透平型发电机非正常运行工况设计和应用导则

本标准规定了透平型发电机在各种非正常运行工况下运行范围及程度的相关要求。 本标准适用于100MW以上容量范围的透平型同步发电机。 本标准可作为使用部门和制造部门签定技术协议时的依据。对具体产品若有特殊要求，可由供需双方另行商定。

Design application guide of turbo generators under abnormal operation

JB/T 7071-2005 灯泡式水轮发电机基本技术条件

本标准规定了灯泡式水轮发电机的基本技术要求、试验验收、供货范围、包装运输及保管和承包方的保证。 本标准适用于与水轮机直接连接的三相、5OHz、卧轴灯泡式凸极同步发电机(以下简称灯泡式水轮发电机)。 凡本标准未规定的事项，均应符合GB/T 7894、GB 8564标准中有关规定。

Basic specification for bulb hydro generators

IEEE 421.5-2005 动力系统稳定性研究用励磁系统模型推荐规程

Includes excitation system models on both older equipment as well as modern state-of-the-art excitation system designs. Includes an explanation of each model, definitions of model nomenclature, sample data for most models, etc.

Recommended Practice for Excitation System Models for Power System Stability Studies

DS/EN 88528-11:2004 往复式内燃机驱动的交流发电机组 第11部分：旋转式不间断电源系统 性能要求和试验方法

This International Standard, which forms part of the ISO/IEC 8528 series, specifies criteria, including performance and test methods, for rotary uninterruptible power systems (UPS) arising out of a combination of mechanical and electrical rotating machines. This standard applies to power supplies primarily designed for supplying uninterrupted a.c. power to the consumer. When operated without input mains feed, the power is provided by stored energy and/or reciprocating internal combustion (RIC) engine and the output power is provided by one or more rotating electrical machines. This part 11 applies to a.c. power supplies primarily designed for supplying unin

Reciprocating internal combustion engine driven alternating current generating sets - Part 11: Rotary uninterruptible power systems - Performance requirements and test methods

ANSI/IEEE 1193:2003 标准频率环境敏感度测量指南

Describes the nature of the environmental effects, as well as test methods to evaluate, quantify, and report the sensitivity of the frequency of standard frequency generators under environmental influences such as magnetic fields, atmospheric pressure, humidity, shock, vibration, acceleration, temperature, ionizing radiation, and intermittent operation.

Guide for Measurement of Environmental Sensitivities of Standard Frequency

SAE J1444-2003 评估小型发动机驱动发电机组瞬态响应的程序

The scope of this SAE Recommended Practice is to provide a uniform practice for the testing of small engine powered alternating current generator sets. This document is limited to reciprocating piston engines of less than 14.9 kw (20 BHP).

Procedure for Evaluating Transient Response of Small Engine Driven Generator Sets

IEEE 1193-2003 测量标准频率发生器对环境灵敏度用指南

Describes the nature of the environmental effects, as well as test methods to evaluate, quantify, and report the sensitivity of the frequency of standard frequency generators under environmental influences such as magnetic fields, atmospheric pressure, humidity, shock, vibration, acceleration, temperature, ionizing radiation, and intermittent operation.

Guide for Measurement of Environmental Sensitivities of Standard Frequency Generators

CAN/CSA-C679-2002(C2007) 农场应急电源安装与维护

1. Domaine d?application 1.1 Cette norme présente des renseignements visant à aider les installateurs, le personnel d?entretien, les opérateurs, les concepteurs et autres quant à l?installation, au fonctionnement et à l?entretien convenables des systèmes électriques de secours des fermes. 1.2 Cette norme traite des génératrices entraînées par un moteur et des génératrices entraînées un tracteur qui assurent l?alimentation électrique de secours des fermes. 1.3 Les valeurs présentées en unités SI (métriques) constituent la norme. Les valeurs figurant entre parenthèses ne sont indiquées qu?à titre de renseignements.

Installation and maintenance of farm emergency power supply

IEC 60079-14:2002 爆炸性气体环境的电气设备.第14部分:危险场所(矿井除外)中的电气装置

This part of IEC 60079 contains the specific requirements for the design, selection and erection of electrical installations in explosive gas atmospheres. These requirements are in addition to the requirements for installations in non-hazardous areas. Th

Electrical apparatus for explosive gas atmospheres - Part 14: Electrical installations in hazardous areas (other than mines)

JB/T 10326-2002 在役发电机护环超声波检验技术标准

本标准规定了在役发电机护环超声波检验方法。它适用于壁厚为25mm～100mm，晶粒度为-1级及其以上的发电机护环的超声波检验。 　　本标准所述的检验程序适用于A型脉冲反射接触式超声波检验。

Ultrasonic testing standard for retaining ring in-service

CAN/CSA-C679-2002(R2007) 农用备用电力安装与维护

1. Scope 1.1 This Standard provides information to assist installers, maintenance personnel, operators, designers, and others in the proper installation, operation, and maintenance of farm standby electrical systems. 1.2 This Standard covers both engine-driven and tractor-driven generators for farm standby electrical power. 1.3 The values given in SI (metric) units are the standard. The values given in parentheses are for information only.

Installation and Maintenance of Farm Standby Electric Power

SAE AS17108-2002 轴承，滚珠，环形，主要用于飞机发电机，类型 ii

Bearing, ball, annular, primarily for aircraft generators, type ii

IEEE 1110-2002 电力系统稳定性分析中同步电机模拟操作和应用指南

Categorizes three direct-axis and four quadrature-axis models, along with the basic transient reactance model. Discusses some of the assumptions made in using various models and presents the fundamental equations and concepts involved in generator/system interfacing. Covers, generally, the various attributes of power system stability, recognizing two basic approaches. The first is categorized under large disturbance nonlinear analysis; the second approach considers small disturbances, where the corresponding dynamic equations are linearized. Applications of a range of generator models are discussed and treated. The manner in which generator saturation is treated in stability studies, both in the initialization process as well as during large or small disturbance stability analysis procedures is addressed. Saturation functions that are derived, whether from test data or by the methods, of finite elements are developed. Different saturation algorithms for calculating values of excitation and internal power angle depending upon generator terminal conditions are compared. The question of parameter determination is covered. Two approaches in accounting for generator field and excitation system base quantities are identified. Conversion factors are given for transferring field parameters from one base to another for correct generator/excitation system interface modeling, suggestions for modeling of negative field currents and other field circuit discontinuities are included.

Guide for Synchronous Generator Modeling Practices and Applications in Power System Stability Analyses

ANSI/IEEE 1110:2002 电源系统稳定性分析中同步发电机建模规程和应用指南

Summarizes available practices in synchronous machine models used in power system stability studies.

Guide for Synchronous Generator Modeling Practices and Applications in Power System Stability Analyses

IEC 60034-7:2001 旋转电机结构型式、安装型式接线盒的位置的分类(IM代码)

本标准规定了旋转电机的结构型式、安装型式及接线盒位置的分类——IM代码。 两种分类方法规定如下： 代码1(见第2章)：字母数字代号适用于具有端盖式轴承和一个轴伸的电机。 代码2(见第3章)：全数字代号适用于更广的电机型式，包括代码1涉及的电机型式。 代码2中未列入的电机型式应作完整的文字说明。 代码1和代码2之间的关系见附录A(资料性附录)。

Rotating electrical machines--Classification of types of construction,mounting arrangements and terminal box position for (IM Code)

JB/T 3334.1-2000 水轮发电机用制动器.第1部分：立式水轮发电机用制动器

　　本标准规定了立式水轮发电机用活塞式机械制动器的系列、标注型式、基本尺寸、技术要求、试验方法及检验规则。 　　本标准规定的制动器具有制动和顶起两种功能。 　　本标准适用于有制动和顶起转动部分要求的立式水轮发电机。对于无顶起功能要求、不设锁定机构，但有强迫制动停机要求的灯泡式水轮发电机，可参照使用。 　　凡本标准未规定的事项，均应符合GB/T 7894中的有关规定。

Brake for hydraulic generator.Part 1:brake for vertical shaft hydraulic generator