共找到 351 条与 相关的标准,共 24 页
이 표준은 완전한 제품 설명 없이 익스팬더/세그먼트 오일-컨트롤 링의 기본 특성에 관해서 기술한다(익스팬더-스페이서 디자인은 피스톤 링 제작자에 따라서 다양하기 때문에, 제작자와 주문자 간의 합의 사항에 따라 특정한 디자인 상세도가 결정된다).이 표준은 도로 차량용 왕복형 내연 기관에 대한 호칭 지름 40 mm∼125 mm 범위의 익스팬더/세그먼트 오일 컨트롤 링에 적용한다. 유사한 조건하에서 작동하는 압축기의 피스톤 링에도 또한 적용한다.?
Internal combustion engines — Piston rings — Expander/segment oil-control rings
Cylinder liners for automotive engines
이 표준은 4사이클 자동차 엔진에 사용하는 실린더 라이너에 대하여 규정한다. 다만 경합금제 실린더 블록에 주물까지 합쳐서 사용하는 실린더 라이너에는 적용하지 않는다.
Cylinder liners for automotive engines
This document describes methodologies to determine the causes blow-by oil consumption caused by the power cylinder.
Power Cylinder Blow-by: Problem Solving
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mou
Engine Flywheel Housing and Mating Transmission Housing Flanges
This part of ISO 18669 specifies the essential dimensional characteristics of piston pins with an outer diameter between 8 mm and 100 mm, for reciprocating internal combustion engines for road vehicles and other applications. In addition, it establishes a vocabulary, a pin-type classification, material description based on mechanical properties, common features and quality requirements. The use of this part of ISO 18669 may require a manufacturer and customer statistical process control agreement.
Internal combustion engines -- Piston pins -- Part 1: General specifications
This part of ISO 18669 defines the measuring principles to be used for measuring piston pins; it applies to piston pins from 8 mm up to and including 100 mm outside diameter for reciprocating internal combustion engines and compressors. In certain applications, except road vehicles, and provided that mutual agreement is made between the purchaser and the manufacturer, this part of ISO 18669 may be used with suitable modifications.
Internal combustion engines -- Piston pins -- Part 2: Inspection measuring principles
Methods of test for constant speed diesel engines
Belt drives-Pulleys and V-ribbed belts for the automotive industry-PK profile:Dimensions
Belt drives-Pulleys and V-ribbed belts for the automotive industry-PK profile:Dimensions
Glossary of terms relating to rotary engine
Sleeve type flanged half bearings for automobile engines
Internal combustion engines. Piston rings. Rectangular rings made of steel
This part of ISO 6622 specifies the essential dimensional features of rectangular rings made of steel, types R, B, BA, and M having nominal diameters from 30 mm up to and including 160 mm, used in reciprocating internal combustion piston engines for road vehicles and other applications.
Internal combustion engines.Piston rings.Part 2: Rectangular rings made of steel
이 표준은 자동차 엔진용 흡기ㆍ배기 밸브(이하 밸브라 한다.)에 대하여 규정한다.
Valves for automobile engines
This part of ISO 6621 specifies those quality aspects that are capable of definition but not normally found on a drawing specification.
Internal combustion engines.Piston rings.Part 5: Quality requirements
Internal combustion engines. Piston rings. Quality requirements
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号