43.060.40 标准查询与下载

GB/T 5923-1986 汽车柴油机燃油滤清器的试验方法

本标准适用于汽车柴油机及燃油喷射装置试验设备的燃油滤清器。本标准规定的试验方法也可用 于燃用无残渣矿物油的柴油机燃油滤清器。 本标准适用于额定流量在200L/h以下的燃油滤清器。

Test methods of fuel filters for automotive compression ignition engines

GB/T 5924-1986 汽车柴油机燃油滤清器的试验值及分级

本标准适用于汽车柴油机的燃油滤清器及燃油喷射装置试验设备的燃油滤清器。

Test values and classification of fuel filters for automotive compression ignition engines

BS ISO 22760-4:2024 道路车辆 二甲醚（DME）燃油系统部件 液位指示器

Road vehicles — Dimethyl ether (DME) fuel system components - Level indicator

BS ISO 22760-9:2024 道路车辆 二甲醚（DME）燃油系统部件 压力释放装置（PRD）

Road vehicles. Dimethyl ether (DME) fuel system components - Pressure relief device (PRD)

BS ISO 22760-6:2024 道路车辆 二甲醚（DME）燃油系统部件 压力释放阀（PRV）

Road vehicles. Dimethyl ether (DME) fuel system components - Pressure relief valve (PRV)

BS ISO 22760-3:2024 道路车辆 二甲醚（DME）燃料系统部件-85%截止阀

Road vehicles. Dimethyl ether (DME) fuel system components - 85% stop valve

24/30470350 DC ISO 13296 柴油发动机草案 高压燃油喷射管组件 通用要求和尺寸

Draft ISO 13296 Diesel engines — High-pressure fuel injection pipe assemblies — General requirements and dimensions

24/30468678 DC BS ISO 20766-19 道路车辆 液化石油气 (LPG) 燃料系统组件 第19部分：燃气管泄压阀

BS ISO 20766-19 Road vehicles — Liquefied petroleum gas (LPG) fuel system components - Part 19: Gas-tube pressure relief valves

GSO ISO 20766-24:2024 道路车辆 液化石油气 (LPG) 燃料系统组件 第24部分：燃气管

This document specifies general requirements and definitions for the gas tube component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 24: Gas tubes

GSO ISO 12614-19:2024 道路车辆 液化天然气（LNG）燃料系统组件 第19部分：自动阀

This document specifies tests and requirements for the automatic valve, a liquefied natural gas fuel system component intended for use on the types of motor vehicles defined in ISO 3833. This document is applicable to vehicles using natural gas in accordance with ISO 15403-1 (mono-fuel, bi-fuel or dual-fuel applications). It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically covered herein can be examined to meet the criteria of this document and tested according to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document is based upon a working pressure for natural gas as a fuel of 1,6 MPa [16 bar1]. Other working pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio). For example, 2 MPa (20 bar) working pressure system will require pressures to be multiplied by 1,25.   1 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

Road vehicles — Liquefied natural gas (LNG) fuel system components — Part 19: Automatic valve

GSO ISO 20766-4:2024 道路车辆 液化石油气（LPG）燃料系统组件 第4部分：液位指示器

This document specifies general requirements and definitions of liquefied petroleum gas fuel components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 4: Level indicator

GSO ISO 20766-11:2024 道路车辆 液化石油气 (LPG) 燃料系统组件 第11部分：手动截止阀

This document specifies general information regarding the manual shut off valve component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It provides general design principles and specifies requirements for instructions and marking. It also specifies test requirements for the manual shut off valve. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 11: Manual shut-off valve

GSO ISO 20766-16:2024 道路车辆 液化石油气（LPG）燃料系统组件 第16部分：喷射器和气体混合装置/燃油轨

This document specifies general requirements for the injectors and gas mixing device/fuel rail, components of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 16: Injectors and gas mixing device/fuel rail

GSO ISO 20766-10:2024 道路车辆 液化石油气 (LPG) 燃料系统组件 第10部分：气密外壳

This document specifies general information regarding the gas-tight housing component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles defined in ISO 3833. It provides general design principles and specifies requirements for instructions and marking. It also specifies test requirements for the gas-tight housing. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 10: Gas-tight housing

GSO ISO 20766-2:2024 道路车辆 液化石油气（LPG）燃料系统部件 第2部分：性能和一般测试方法

This document specifies performance and general test methods of liquefied petroleum gas fuel system components, intended for use on the types of motor vehicles as defined in ISO 3833. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using liquefied petroleum gas in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; and e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 2: Performance and general test methods

GSO ISO 20766-3:2024 道路车辆 液化石油气 (LPG) 燃料系统组件 第3部分：80% 截止阀

This document specifies general requirements and definitions of liquefied petroleum gas fuel components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; and e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 3: 80% stop valve

GSO ISO 20766-1:2024 道路车辆 液化石油气（LPG）燃料系统组件 第1部分：一般要求和定义

This document specifies general requirements and definitions of liquefied petroleum gas fuel system components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; and e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane rich at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 1: General requirements and definitions

GSO ISO 20766-6:2024 道路车辆 液化石油气 (LPG) 燃料系统组件 第6部分：泄压阀 (PRV)

This document specifies general requirements and definitions of liquefied petroleum gas fuel components, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; and e) refuelling receptacles. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 6: Pressure relief valves (PRV)

GSO ISO 20766-14:2024 道路车辆 液化石油气 (LPG) 燃料系统组件 第14部分：汽化器/压力调节器

This document specifies general requirements for the vaporizer/pressure regulator, a component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20766 series, including testing to the appropriate functional tests. All references to pressure in this document are considered gauge pressures unless otherwise specified. This document applies to devices which have a service pressure in the range of 110 kPa (butane rich at 20 °C) and 840 kPa (propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel system components — Part 14: Vaporizer/pressure regulator

GSO ISO 20766-18:2024 道路车辆 液化石油气 (LPG) 燃料系统组件 第18部分：软管

This document specifies general information regarding the hose component of liquefied petroleum gas fuel, intended for use on the types of motor vehicles as defined in ISO 3833. It provides general design principles and specifies requirements for instructions and marking. It also specifies test requirements for the hose. This document is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using gaseous fuels in accordance with ISO 9162. It is not applicable to the following: a) fuel containers; b) stationary gas engines; c) container mounting hardware; d) electronic fuel management; e) refuelling receptacles. Fully metal bendable hoses are excluded from this document. NOTE 1 It is recognized that miscellaneous components not specifically addressed herein can be examined for compliance with the criteria of any applicable part of ISO 20766, including testing to the appropriate functional tests. NOTE 2 All references to pressure in this document are considered gauge pressures unless otherwise specified. NOTE 3 This document applies to devices which have a service pressure in the range of 110 kPa (Butane rich at 20 °C) and 840 kPa (Propane at 20 °C), hereinafter referred to in this document. Other service pressures can be accommodated by adjusting the pressure by the appropriate factor (ratio).

Road vehicles — Liquefied petroleum gas (LPG) fuel systems components — Part 18: Hose