59.080.20 纱线 标准查询与下载

T/CCTA 30403-2022 赛络紧密纺莱赛尔纤维本色纱

本文件规定了赛络紧密纺莱赛尔纤维（棉型）本色纱的术语和定义、产品分类、标记、要求、试验方法、检验规则和标志、包装。本文件适用于赛络紧密纺莱赛尔纤维本色纱。

Siro compact spun lyocell natural yarn

EN IEC 63203-201-1:2022 可穿戴电子设备和技术-第 201-1 部分：电子纺织品-导电纱线基本性能的测量方法

IEC 63203-201-1:2022 specifies provisions and test methods for measurement of properties of conductive yarns. Conductive yarns covered in this document have conductivity of a level that can be used for transmission of electric signals, supply of electric power and electromagnetic shield. They do not include high-resistance conductive yarn used for anti-static and heating use. Conductive yarns are the basic material in electronic textiles and are mainly used as conductive traces in clothes-type wearable devices, as well as with secondary processing (woven, knitted, embroidered, nonwoven, etc.) to provide conductive fabrics. This document does not define the required characteristics of the conductive yarn; rather, it specifies the handling and measurement methods for general and electrical properties of conductive yarn.

Wearable electronic devices and technologies - Part 201-1: Electronic textile - Measurement methods for basic properties of conductive yarns

ASTM D4974/D4974M-22 用热收缩烘箱测定纱线和帘线的热空气热收缩的标准试验方法

1.1 This test method covers the measurement of shrinkage of yarns and cords when exposed in a thermal shrinkage oven. 1.2 This test method is applicable to yarns and cords made of nylon, polyester, and other polymers not detrimentally affected by the temperature used and with linear densities in the range from 20 to 700 tex [180 to 6300 denier]. 1.2.1 Yarns or cords for testing may be taken from yarn or cord packages or from fabrics. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. Referee decisions are to use SI units. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Hot Air Thermal Shrinkage of Yarn and Cord Using a Thermal Shrinkage Oven

KS F 3888-1-2022 人造草坪系统

Artificial turf systems

DB4212/T 49-2022 短麻纺纯苎麻纱

Short hemp spun pure ramie yarn

T/CNTAC 94-2022 本色纱线异性纤维检测与分级

本文件给出了用纱疵分级仪对本色短纤维纱线中深色异性纤维进行检测和分级的方法。

Testing and classifying the foreign fibers on grey yarn

IEC 63203-201-1:2022 可穿戴电子设备和技术第201-1部分:电子纺织品导电纱基本性能的测量方法

Wearable electronic devices and technologies - Part 201-1: Electronic textile - Measurement methods for basic properties of conductive yarns

FZ/T 22018-2022 精梳牦牛绒机织纱

Combed yak wool woven yarn

FZ/T 22019-2022 气流纺机织毛纱

Air spinning woolen yarn

SN/T 5431.2-2022 进口固体废物鉴别方法 纺织原料及制品 第2部分：纱线

Identification method of imported solid waste Textile raw materials and products Part 2: Yarn

T/CCTA 30501-2022 涤粘混纺包涤氨双芯本色纱

本文件规定了涤粘混纺包涤氨双芯本色纱的术语和定义、产品分类、标记、要求、试验方法、检验规则和标志、包装。本文件适用于22 dtex～83 dtex涤纶低弹丝和22 dtex～77 dtex氨纶作为双芯，外包涤纶（棉型短纤维，含量≥50%）和粘胶纤维（棉型短纤维）的环锭纺涤粘混纺包涤氨双芯本色纱。 涤粘混纺包涤氨双芯本色纱技术要求包括线密度偏差率、线密度变异系数、单纱断裂强度、单纱断裂强力变异系数、条干均匀度变异系数、千米棉结（+200%）、十万米纱疵、纤维含量偏差、外观质量九项指标。

Polyester-viscose blended polyester-spandex double core natural color yarn

ASTM D1423/D1423M-16(2022) 用直接计数法测定纱线捻度的标准试验方法

1.1 This test method covers the determination of the amount and direction of twist at the completion of any stage of twisting in single (spun or filament), plied, cabled, or novelty (exclusive of long-term repeat patterns) yarns. The procedures are designed primarily for yarns in packages, but, with special precautions, they are applicable to yarns taken from fabrics. The procedure for spun yarn in 9.2 is also applicable to rovings. 1.2 For plied yarns, this test method covers the determination of the twist of the plied yarns and the twist of the single yarn before plying. For cabled yarns, the test method covers the determination of the cable or hawser twist; the twist of the plied yarn after plying, but prior to the last twisting operation; and the twist of the single yarn before plying. Procedures are also included for the determination of the twists of the single and plied yarn components as they lie in the final structure. Also, directions are included for the determination of twist in plied yarn made with direct cabling technology. 1.3 This test method is not intended for yarns that extend more than 5.0 % when tension is increased from 2.5 to 7.5 mN/tex [0.25 to 0.75 gf/tex]. Following the procedures of this test method for such yarns would be independent of the bias and precision determined for this test method. The report from such testing should include the tension used for this testing. 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. NOTE 1—For a more rapid but less accurate method of determining twist in single spun yarns, refer to Test Method D1422. NOTE 2—This test method has been evaluated for use in determining twist in open end yarns and is not recommended. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Twist in Yarns by Direct-Counting

ASTM D6612-00(2022) 用自动测试仪测定纱线数和纱线数可变性的标准试验方法

1.1 This test method covers the measurement of yarn number up to 4000 dtex (3600 denier) and related variability properties of filament and spun yarns using an automated tester with capability for measuring mass variability characteristics. 1.2 Yarn number variability properties include percent density spread (%DS), coefficient of variation (%CV), density frequency variation. NOTE 1—For determination of yarn number by use of reel and balance, refer to Test Method D1907. For another method of measuring variability (unevenness) in yarn, refer to Test Method D1425. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore to ensure conformance with this standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Yarn Number and Yarn Number Variability Using Automated Tester

ASTM D2258/D2258M-16(2022) 试验用纱线取样的标准实施规程

1.1 This practice describes a procedure for the division of shipments of yarn into test lots and the sampling of such lots for testing. 1.1.1 This practice can be used for lot sample testing of yarns for both pre-fabric production and post-fabric production. 1.2 This practice is applicable to single, plied, or cabled yarns, and cords, made of any fiber or mixture of fibers, and supported on any form of package, including beams. 1.3 This practice also describes procedures for the sampling of yarn(s) removed from woven or knitted fabrics; however, when thus sampled, the yarns are usually not representative of entire shipments, as referred to in 1.1. Consequently, the resultant sampling can only be used to determine the characteristics of the yarn and is usually not used for acceptance testing. Moreover, it should be recognized that the characteristics of yarns from fabrics may be different than the characteristics of the same yarn(s), prior to being entered into the fabric manufacturing process. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling Yarn for Testing

T/TYZSH 001-2021 喷气涡流纺腈纶本色纱

本文件规定了喷气涡流纺腈纶本色纱产品的分类、标识、要求、试验方法、检验规则、标志和包装。 本文件适用于以100%腈纶短纤维为主要原料，经过喷气涡流纺纱工艺制成的喷气涡流纺腈纶本色纱。

Acrylic air-jet vortex spun grey yarn

T/CNTAC 87-2021 聚乳酸纤维与棉混纺纱

本文件规定了聚乳酸纤维与棉混纺纱产品的分类、标记、要求、试验方法、检验规则、标志、包装、运输和贮存。

Polylactide and cotton blended yarns

ISO 24180:2021 纺织品.合成长丝纱.通过测量电阻评估静电倾向

This document specifies methods for electrostatic propensity evaluation by measuring electrical resistance of synthetic filament yarns. It is applicable to synthetic filament yarns. Conductive yarns covered in this document are used for anti-static fabric. They are not used for transmission of electric signals, supply of electric power and electromagnetic shield and heating.

Textiles — Synthetic filament yarns — Electrostatic propensity evaluation by measuring electrical resistance

T/ZFB 0011-2021 织物用再加工纤维棉纱

5 要求 织物纱应符合表1、表2的要求。 6 试验方法 6.1 线密度偏差率和线密度变异系数 按GB/T 4743─2009规定执行，线密度偏差率按式（1）计算，其中100m 纱的实测干燥质量按程序2烘干后折算，100m 纱的标准干燥质量按附录A 中式（A.4）计算。线密度变异系数按程序1调湿平衡后，按式（2）计算。计算结果按GB/T 8170修约至小数点后一位。 6.2 单纱断裂强度及单纱断裂强力变异系数 按GB/T 3916 规定执行。 6.3 条干均匀度变异系数、千米棉结（+200%） 按GB/T 3292.1 规定执行。 6.4 明显色结 按FZ/T 10021─2013 中附录A规定执行。 6.5 十万米纱疵试验 按FZ/T 01050 规定执行，十万米纱疵结果用A3、B3、C3、D2以上九级疵点之和表示。 6.6 纤维含量 按FZ/T 01057（所有部分）、GB/T 2910（所有部分）和FZ/T 01026 等规定执行。 6.7 甲醛含量 按GB/T 2912.1 规定执行。 6.8 pH值 按GB/T 7573 规定执行。 6.9 异味 按GB 18401 规定执行。 6.10 可分解致癌芳香胺染料 按GB/T 17592 规定执行。 6.11 余氯试验 按GB/T 28025 规定执行。 6.12 有机氯载体 按GB/T 20384 规定执行。 6.13 耐皂洗色牢度 按GB/T 3921─2008 规定执行，采用单纤维贴衬，试验条件为A（1）。 6.14 耐水色牢度 按GB/T 5713 规定执行，采用单纤维贴衬。 6.15 耐汗渍色牢度 按GB/T 3922 规定执行，采用单纤维贴衬。 6.16 耐摩擦色牢度 按GB/T 3920 规定执行。 6.17 微生物 绿脓杆菌、金黄色葡萄球菌、溶血性链球菌、大肠杆菌、真菌菌落总数和细菌菌落总数项目按GB 15979─2002 附录B 规定执行。 7 检验规则 按FZ/T 10007 规定执行，其中每批另行抽取1个筒子为微生物试验样品，抽取后密封包装，不进行任何处理。

Yarn with recycled fiber used for fabrics

T/ZFB 0012-2021 拖把用再加工纤维纱

5 要求 拖把纱应符合表1、表2 的要求。 6 试验方法 6.1 线密度偏差率 按GB/T 4743—2009 执行。其中，线密度偏差率按式（1）计算，100m 纱的实测质量按程序1调湿平 衡后计算，100m 纱的标准质量按设计质量计算。计算结果按GB/T 8170修约至小数后一位。 6.2 单纱断裂强度及单纱断裂强力变异系数 按GB/T 3916 规定执行。 6.3 异味 按GB 18401 规定执行。 6.4 洗液沾色程度 按FZ/T 73020—2019中6.1.11 规定执行。 6.5 耐摩擦色牢度 按GB/T 3920 规定执行。 6.6 吸水率 按GB/T 21655.1—2008 规定执行,试验样品质量为50g，试样样品数量5个，每个样品整理成20cm 圈 长的纱绞。 6.7 脱毛率 按GB/T 22798—2019 中A法规定执行 6.8 余氯 按GB/T 28025 规定执行。 6.9 微生物 绿脓杆菌、金黄色葡萄球菌、溶血性链球菌、大肠菌群项目按GB 15979—2002 附录B 规定执行。 7 检验规则 按FZ/T 10007 规定执行，其中每批另行抽取1 个筒子为微生物试验样品，抽取后密封包装，不进行 任何处理。

Yarn with recycled fiber used for mops

T/CTES 1047-2021 阻燃缝纫线

本文件规定了阻燃缝纫线的分类、要求、试验方法、验收规则、标志、包装、运输和贮存。 本文件适用于在有明火、散发火花，或在有易燃物质并有轰燃风险场所使用的、纯纺或混纺本质阻燃、永久性阻燃缝纫线及后整理阻燃缝纫线。其他阻燃缝纫线可参考。

Flame retardant sewing thread