77.140.01 钢铁产品综合 标准查询与下载

T/TJSS 001-2021 高频焊接H型钢

本标准的主要内容包括：1.范围；2.规范性引用文件；3.术语和定义；4.代号和标记；5.要求；6.试验和检测方法；7.检验规则；8.标志；9.包装、运输和贮存以及附录。

High Frequency Welded H Steel Sections

BS ISO 630-4:2021 结构钢 高屈服强度调质结构钢板和宽扁钢板交货技术条件

What is ISO 630 ‑ 4 about?    ISO 630-4 is the fourth part in the multi-series of International Standards on ‘Steels for structural purposes’. ISO 630 ‑ 4 specifies qualities for high-yield-strength quenched and tempered structural steels. ISO 630 ‑ 4 applies to steel plates and wide flats rolled on a reversing mill which is used in the quenched and tempered condition and normally intended for welded or bolted structures.   ISO 630

Structural steels - Technical delivery conditions for high yield strength quenched and tempered structural steel plates and wide flats

KS D 8505-2021 吸氢合金氢化反应热的测定方法

Method for measuring the heat of hydriding reaction of hydrogen absorbing alloys

DS-håndbog 111.2.1:2021 钢铁—2.1部分：结构钢热轧产品

Iron and steel – Part 2.1: Hot rolled products of structural steels

BS ISO 630-2:2021 结构钢 通用结构钢交货技术条件

Structural steels. Technical delivery conditions for structural steels for general purposes

BS ISO 630-3:2021 结构钢 细粒结构钢交货技术条件

Structural steels. Technical delivery conditions for fine-grain structural steels

BS ISO 630-1:2021 结构钢 热轧产品交货通用技术条件

Structural steels. General technical delivery conditions for hot-rolled products

ISO 630-3:2021 结构钢 第3部分:细晶粒结构钢交货技术条件

This document specifies requirements for flat and long products of hot-rolled weldable fine- grain structural steels in the as-rolled (for SG grades only), normalized/normalized rolled and thermomechanical processed delivery conditions. It applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are intended for use in heavily loaded parts of welded or bolted structures. This document covers 13 grades and 6 qualities. Grades S275, S355, S390, S420, S460 and S500 are covered in Annex A. Grades SG245, SG290, SG325, SG345, SG365, SG415 and SG460 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. The steels specified in this document are applicable to hot-rolled plates, wide flats, sections and bars with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 250 mm for grades S275N, S355N, S390N, S420N and S460N, a maximum nominal thickness of 150 mm for grades S275M, S355M, S390M, S420M, S460M, and S500M, a maximum nominal thickness of 200 mm for grades SG245, SG325 and SG415, a maximum nominal thickness of 100 mm for grades SG345, SG365 and SG460, and a maximum nominal thickness of 40 mm for grade SG290. This document does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.

Structural steels — Part 3: Technical delivery conditions for fine-grain structural steels

ISO 630-1:2021 结构钢 - 第1部分:热轧产品的一般技术交付条件

This document specifies the general technical delivery conditions for steel flat and long products (plates/ sections/wide flats and bars) used principally for general-purpose structural steels. The steels specified in this document are intended for use in welded or bolted structures. The specific requirements for structural steels are given in the individual parts of ISO 630. This document does not include the following structural steels, some of which are covered by other International Standards: — sheet and strip: refer to ISO TC 17/SC 12 “Continuous mill flat rolled products”; — tubular products: refer to ISO TC 5/SC 1 “Steel tubes”. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.

Structural steels — Part 1: General technical delivery conditions for hot-rolled products

ISO 630-4:2021 结构钢. 第4部分: 高产强度淬火和回火结构钢和宽扁钢的技术交货条件

This document specifies qualities for high-yield-strength quenched and tempered structural steels. It applies to steel plates and wide flats rolled on a reversing mill which are used in the quenched and tempered condition and normally intended for welded or bolted structures. This document covers 10 grades and 5 qualities. Grades S460Q, S500Q, S550Q, S620Q, S690Q, S890Q and S960Q are covered in Annex A. Grades SG460Q, SG500Q, and SG700Q are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460Q, S500Q, S550Q, S620Q and S690Q, a maximum nominal thickness of 125 mm for grades S890Q and S960Q, a maximum nominal thickness of 100 mm for grades SG460Q and SG500Q and a maximum nominal thickness of 150 mm for grade SG700Q. This document does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE 1 Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. NOTE 2 In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise stated.

Structural steels - Part 4: Technical delivery conditions for high yield strength quenched and tempered structural steel plates and wide flats

ISO 630-2:2021 结构钢. 第2部分: 结构钢通用目的技术交货条件

This document specifies qualities for steels for general structural use. This document applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are used in the asdelivered condition and normally intended for welded or bolted structures. This document covers 8 steel grades and 4 qualities. Grades S235, S275, S355, and S460 are covered in Annex A. Grades SG205, SG250, SG285 and SG345 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. The steels specified in this document are applicable to hot-rolled flat products and sections with: — thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S460 all qualities; — thicknesses ≥ 3 mm and ≤ 250 mm for long products or ≤ 400 mm for flat products of all other grades and qualities; and no restriction on nominal thickness for grades SG205, SG250, SG285, and SG345 for flat products, sections and long products. This document does not include the following structural steels, some of which are covered by other International Standards: — sheet and strip: refer to ISO TC 17/SC 12 “Continuous mill flat rolled products”; — tubular products: refer to ISO TC 5/SC 1 “Steel tubes”. NOTE 1 NOTE 2 stated. Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO website. In all parts of ISO 630, the term of "thickness" is considered as "nominal thickness", unless otherwise

Structural steels - Part 2: Technical delivery conditions for structural steels for general purposes

T/SSEA 0113-2021 MEC处理钢材表面质量等级

本文件规定了采用机械柔性水磨法去除钢材表面氧化铁皮（MEC）的技术处理钢材表面质量等级的分类和代号、表面质量等级、检验方法、检验规则、等级标识。 本文件适用于碳素结构钢、低合金结构钢、不锈钢的热轧钢板和钢带以及热轧盘条产品经MEC处理后的表面质量等级，其他热轧钢材产品经MEC处理后的表面质量等级可参考使用。

MEC treated steel surface quality grade

T/SSEA 0098-2021 热连轧花纹钢带

本文件规定了热连轧花纹钢带的分类、代号及牌号表示方法、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志和质量证明书等内容。 本文件适用于厚度为2.3mm～10.5mm的热轧花纹钢带（以下简称钢带）

Hot rolling patterned steel strip

T/SSEA 0101-2021 螺丝成型精冲用高速工具钢

本文件规定了螺丝成型精冲用高速工具钢的订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、标志和质量证明书。 本文件适用于制造螺丝成型精冲用直径10mm~35mm的高速工具钢热轧圆钢及银亮圆钢（以下简称圆钢）。

High speed tool steel for fine blanking of screw forming

PNST 531-2021 石油和天然气工业 海底生产系统 热锻非合金和合金钢棒 规格

Petroleum and natural gas industry. Subsea production systems. Hot-Wrought non-alloy and Alloy Steel Bars. Specifications

ASTM A1012-10(2021) 带有整体散热片的无缝和焊接铁素体, 奥氏体和双相合金钢冷凝器和换热器管的标准规范

1.1?This specification describes seamless and welded ferritic, austenitic and duplex alloy steel tubing on which the external or internal surface, or both, has been modified by a cold forming process to produce an integral enhanced surface for improved heat transfer. The tubes a

Standard Specification for Seamless and Welded Ferritic, Austenitic and Duplex Alloy Steel Condenser and Heat Exchanger Tubes With Integral Fins

JIS G 3101:2020 普通结构用轧制钢

Rolled steels for general structure

KS D 4000-2020 钢铁副产品直接还原铁

Direct reduced iron from iron and steel by-products

YB/T 4829-2020 钢板镀层质量试验方法 在线X射线荧光法

Steel plate coating quality test method online X-ray fluorescence method

T/CAMT 6-2020 《钢板剪切加工中心建设与管理规范》

1  范围   2  规范性引用文件  3  术语和定义  4  加工中心建设要求 4.1  一般要求   4.2  项目可行性研究  4.3  选址 4.4  功能要求  4.5  工艺布局 4.6  建筑要求 4.7  设备设施要求   4.8  厂区环境   4.9  建设项目管理要求 5  加工中心加工管理    5.1  一般要求    5.2  制度规范   5.3  作业运行   5.4  客户服务  附录A  加工中心典型工艺布局 附录B  中心设备采购、安装、调试以及验收要点  附录C  建设项目各阶段展开工作 附录D  项目土建招标所需准备资料清单 附录E  建设项目基建资料归档清单 附录F  建设项目设备资料归档清单 附录G  加工中心各类安全规范图示 附录H  热轧剪切产品常用包装方式和适用产品 附录I  冷轧剪切产品常用包装方式和适用产品

Code for Construction and Management of Steel Plate Shearing Processing Center