77.140.01 钢铁产品综合 标准查询与下载

DB53/T 463-2013 出口美味牛肝菌加工规格要求

本标准规定了出口美味牛肝菌加工规格的术语和定义、产品分类、要求、检验方法和检验规则。本标准适用于出口美味牛肝菌加工规格及贸易要求。

Processing Specifications for Exporting Delicious Boletus

DB53/T 448-2012 非贮压式超细干粉灭火系统设计、施工及验收规范

本标准规定了非贮压式超细干粉灭火系统的术语和定义、系统设计、系统施工、验收和维护。本标准适用于新建、改建、扩建的各类建筑工程中设置的非贮压式超细干粉灭火系统的设计、施工、验收和维护管理。

Specifications for design, construction and acceptance of non-storage pressure ultra-fine dry powder fire extinguishing system

DB53/T 427-2012 热轧锚杆钢

本标准规定了热轧锚杆钢的术语和定义、分类与牌号、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书等。本标准适用于矿山、公路、公路边坡治理工程、桥梁、隧道、建筑物的抗震加固及设备基础的热轧锚杆钢。

Hot Rolled Anchor Steel

DB53/T 426-2012 冷轧钢板及钢带表面残留物的测定

本标准规定了冷轧钢板及钢带表面残留物及残铁的测定方法。本标准适用于用重量法测定冷轧钢板及钢带表面残留物的测定方法及电感耦合等离子体原子发射光谱法测定残铁的测定方法。含量测定范围：残留物为100 mg/m2～3 000 mg/m2；残铁为10 mg/m2～500 mg/m2。

Determination of residues on the surface of cold-rolled steel sheets and strips

ISO 630-3:2012 结构钢.第3部分:细粒结构钢的技术交货条件

This part of ISO 630 specifies requirements for flat and long products of hot-rolled weldable fine-grain structural steels in the as-rolled (for SG grades only), normalized/normalized-rolled and thermomechanical-rolled delivery conditions. It applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are intended for use in heavily loaded parts of welded or bolted structures. This part of ISO 630 covers 11 grades and four qualities. Grades S275, S355, S420 and S460 are covered in Annex A. Grades SG245, SG290, SG325, SG345, SG365, SG415 and SG460 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site.

Structural steels - Part 3: Technical delivery conditions for fine-grain structural steels

ISO 630-4:2012 结构钢.第4部分:高产强度淬火和回火结构钢的技术交货条件

This part of ISO 630 specifies qualities for high-yield-strength quenched and tempered structural steels. This part of ISO 630 applies to steel plates rolled on a reversing mill which are used in the quenched and tempered condition and normally intended for welded or bolted structures. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — Sheet and strip — refer to ISO TC 17/SC 12, Continuous mill flat rolled products; — Tubular products — refer to ISO TC 5/SC 1, Steel tubes. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site. This part of ISO 630 covers 10 grades. Grades S460Q, S500Q, S550Q, S620Q, S690Q, S890Q and S960Q are covered in Annex A. Grades SG460Q, SG500Q, and SG700Q are covered in Annex B.

Structural steels - Part 4: Technical delivery conditions for high-yield-strength quenched and tempered structural steel plates

DB53/T 398-2012 固定式燃气型超音速干粉灭火系统设计、施工及验收规范

本标准规定了固定式燃气型超音速干粉灭火系统的术语与定义、基本要求、系统设计、安装施工、验收和维护。本标准适用于建筑工程中的固定式燃气型超音速干粉灭火系统。本系统可用于扑救下列火灾： ——灭火前可切断气源的气体火灾； ——易燃、可燃液体和可熔化固体火灾； ——可燃固体表面火灾； ——带电设备火灾。本系统不适用于扑救下列物资的火灾： ——硝化纤维、炸药等无空气仍能迅速氧化的化学物质与强氧化剂； ——钾、钠、镁、钛、锆等活泼金属及其氢化物。

Specifications for design, construction and acceptance of fixed gas type supersonic dry powder fire extinguishing system

DB53/T 380-2012 烟草烤炉用耐腐蚀热轧钢带

本标准规定了烟草烤炉用耐腐蚀热轧钢带的牌号表示方法、订货内容、尺寸、外形、重量及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书等。本标准适用于厚度为3.5 mm～6.0 mm、宽度为500 mm～1 520 mm的烟草烤炉用耐腐蚀热轧钢带（以下简称“钢带”）。

Corrosion-resistant hot-rolled steel strip for tobacco ovens

DB53/T 379-2012 冷轧用热轧中宽钢带

本标准规定了冷轧用热轧中宽钢带的术语和定义、订货内容、尺寸、外形及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书等。本标准适用于公称宽度为410 mm～740 mm的冷轧用热轧中宽钢带（以下简称“中宽钢带”）。

Hot rolled medium and wide steel strip for cold rolling

NB/T 20005.8-2012 压水堆核电厂用碳钢和低合金钢.第8部分：S1、S2 级支承件用钢板、型钢和钢棒

本部分规定了压水堆核电厂S1、S2级支撑件用碳钢和低合金钢钢板、型钢和钢棒的制造、试验、检验和验收等技术要求。 本部分适用于压水堆核电厂S1、S2级支撑件用型钢、厚度小于或等于150mm钢板和直径或厚度小于或等于100mm的钢棒。

Carbon steel and low alloy steel for PWR nuclear power plant.Part 8:Steel plates,beams and bars for class S1 and S2 supports

NB/T 20005.4-2012 压水堆核电厂用碳钢和低合金钢.第4部分：主蒸汽系统、主给水流量控制系统、辅助给水系统和汽轮机旁路系统用锻、轧件

本部分规定了压水堆核电厂主蒸汽系统、主给水流量控制系统、辅助给水系统和汽轮机旁路系统用P280GH锻、轧件的制造、化学成分、力学性能、试验方法、检验规则等技术要求。 本部分适用于压水堆核电厂主蒸汽系统、主给水流量控制系统、辅助给水系统和汽轮机旁路给水系统用P280GH锻、轧件。

Carbon steel and low alloy steel for pressurized water reactor nuclear power plants.Part 4:The forged or rolled parts for use in steam generator main steam systems,feedwater flow control systems,auxiliary feedwater systems and turbine bypass systems

GOST 31443-2012 工艺管道用钢管.规格

Steel pipes for crafts pipelines. Specifications

ANSI/AISI S214-2012 冷轧成型钢框架的北美标准.桁架设计

North American Standard for Cold-Formed Steel Framing - Truss Design

GOST 31458-2012 钢管,管子和管制品.检验文件

Steel pipes, tubes and pipe products. Inspection documents

GOST 31444-2012 海底管道用低合金钢管.规格

Pipes from low-alloy steel for submsrine sea pipelines. General specifications

DB13/T 1484-2011 无缝钢管与焊接钢管鉴别 金相法

Metallographic method for identification of seamless steel pipe and welded steel pipe

GSO EN 40-5:2011 灯杆 第5部分：钢灯杆的要求

This European Standard specifies requirements for steel lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns. This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under impact in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards. It provides for the evaluation of conformity of the products to this European Standard.

Lighting columns - Part 5: Requirements for steel lighting columns

ISO 630-1:2011 结构钢.第1部分:热轧制品的一般技术交货条件

This part of ISO 630 specifies the general technical delivery conditions for steel flat and long products (plate/ sections/wide flats and bars) used principally for general-purpose structural steels. The steels specified in this part of ISO 630 are intended for use in welded or bolted structures. The specific requirements for structural steels are given in the individual parts of ISO 630. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — sheet and strip: refer to ISO TC 17/SC 12 “Continuous mill flat rolled products”; — tubular products: refer to ISO TC 5/SC 1 “Steel tubes”. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site.

Structural steels - Part 1: General technical delivery conditions for hot-rolled products

ISO 630-2:2011 结构钢.第2部分:结构钢通用目的技术交货条件

This part of ISO 630 specifies qualities for steels for general structural use. This part of ISO 630 applies to steel plates rolled on a reversing mill, wide flats, hot-rolled sections and bars, which are used in the as-delivered condition and normally intended for welded or bolted structures. This part of ISO 630 covers eight steel grades and four qualities. Grades S235, S275, S355, and S450 are covered in Annex A. Grades SG205, SG250, SG285 and SG345 are covered in Annex B. Not all grades are available in all qualities, and some qualities have Charpy V-notch requirements. This part of ISO 630 does not include the following structural steels, some of which are covered by other International Standards: — sheet and strip: refer to ISO TC 17/SC 12 “Continuous mill flat rolled products”; — tubular products: refer to ISO TC 5/SC 1 “Steel tubes”. NOTE Lists of standards covered by ISO/TC 17/SC 12 and ISO/TC 5/SC 1 are available on the ISO Web site.

Structural steels - Part 2: Technical delivery conditions for structural steels for general purposes

ABNT NBR 6655-2011 改进机械性能、拉深性和焊接性的热轧镇静钢板和薄板规范

This standard stablishes the required requirements for ordering, manufacturing and supplying hot-rolled coils and sheets, carbon and high-strength low-alloy killed steel, with thickness form 2 mm incl. to 16 mm incl., intended for applications where special requirements of mechanical properties, formability and weldability are fundamental, such as siderails and frames. As previous agreed upon between the purchaser and the producer, this specification could be also applied to plates with thickness over 16 mm.

Hot rolled killed steel plates and sheets with improved mechanical properties, drawability and weldability - Specifi cation