77.140.25 弹簧钢 标准查询与下载

KS D ISO 8458-3-2003(2013) 机械弹簧用钢丝第3部分:油淬回火钢丝

Steel wire for mechanical springs－Part 3：Oil－hardened and tempered wire

KS D ISO 8458-1-2003(2013) 机械弹簧用钢丝第1部分:一般要求

Steel wire for mechanical springs－Part 1：General requirements

NF A35-587*NF EN 10151:2003 弹簧用不锈钢带材.交货技术条件

Stainless steel strip for springs - Technical delivery conditions.

DIN EN 10089:2003 淬火和回火弹簧用热轧钢材.交货技术条件

Hot rolled steels for quenched and tempered springs - Technical delivery conditions; German version EN 10089:2002

DS/EN 10151:2003 弹簧用不锈钢带材 交货技术条件

This standard applies to cold rolled narrow strip of thicknesses up to and including 3 mm in rolled widths less than 600 mm made from the stainless steel grades listed in Table 1. The steels are used in the conditions given in Table 4 for the production of springs and spring parts that are exposed to corrosive effects and sometimes slightly increased temperatures.

Stainless steel strip for springs - Technical delivery conditions

DIN EN 10151:2003 不锈钢弹簧带材.交货技术条件

The document applies to cold rolled narrow strip of thickness up to and including 3 mm in rolled widths less than 600 mm made from the stainless steel grades listed in table 1. The steels are currently used in the conditions given in table 4 for the production of springs and spring parts that are exposed to corrosive effects and sometimes slightly increased temperatures.

Stainless steel strip for springs - Technical delivery conditions; German version EN 10151:2002

BS EN 10089:2002 淬火和回火弹簧用热轧钢.交货技术条件

1.1 This European Standard specifies the technical delivery requirements for round and flat bars, ribbed and grooved bars and rod manufactured from the alloy steels listed in Table 3, intended for hot-formed and subsequently heat-treated springs or cold-formed and subsequently heat-treated springs. The products are supplied in one of the heat-treatment conditions given for the different types of products in Table 1, lines 2 to 6, and in one of the surface conditions given in Table 2. 1.2 In special cases, variations in these technical delivery requirements or additions to them may form the subject of an agreement at the time of enquiry and order (see annex A). 1.3 In addition to the specifications of this European Standard, the general technical delivery requirements of EN 10021 are applicable.

Hot rolled steels for quenched and tempered springs - Technical delivery conditions

BS EN 10151:2002 弹簧用不锈钢带材.交货技术条件

1.1 This European Standard applies to cold rolled narrow strip of thicknesses up to and including 3 mm in rolled widths less than 600 mm made from the stainless steel grades listed in Table 1. The steels are used in the conditions given in Table 4 for the production of springs and spring parts that are exposed to corrosive effects and sometimes slightly increased temperatures. 1.2 Other steel grades than those listed in Table 1, but covered by prEN 10088-2 can be supplied in the above conditions after agreement between supplier and customer (see also annex A). 1.3 The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard.

Stainless steel strip for springs - Technical delivery conditions

DS/EN 10132-4:2002 热处理用冷轧窄钢带 交货技术条件 第4部分：弹簧钢和其他应用

This part of EN 10132 applies to: - non-alloy and alloy cold rolled narrow steel strip thicknesses up to 6 mm; - non-alloy and alloy cold rolled narrow steel strip in the quenched and tempered condition in thicknesses between 0,30 mm and 3,00 mm for springs and for other special applications.

Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Part 4: Spring steels and other applications

ASTM A682/A682M-02 冷轧高碳带材的一般要求

1.1 This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. (7.6 mm) or less in thickness and over 1/2 to 23 15/16 in. (12.5 to 600 mm) in width, inclusive. Strip tolerance products may be available in widths wider than 2315/16 in. (600 mm) by agreement between purchaser and supplier; however, such products are technically classified as cold-rolled sheet.1.2 The maximum of the specified carbon range is over 0.25 % to 1.35 %, inclusive. 1.3 The above shall apply to the cold-rolled carbon spring steel strip furnished under each of the following specifications issued by ASTM:Title of Specification ASTM DesignationSteel, Strip, High Carbon,A 684/A 684MCold Rolled 1.4 The tolerances in this specification are different than those in Specification A 568/A 568M and Specification A 109/A 109M.1.5 For the purpose of determining conformance with this specification, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.6 The metric portions of the tables herein list permissible variations in dimensions and mass (see Note 1) in SI (metric) units. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the "M" specification is used.Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term in mass.1.7 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems will result in nonconformance with the specification.1.8 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.

Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled, General Requirements For

ASTM A682/A682M-00 冷轧高碳带材的一般要求

1.1 This specification covers the general requirements for cold-rolled carbon spring steel strip in coils or cut lengths. Strip is classified as product that is 0.3000 in. (7.6 mm) or less in thickness and over 1/2 to 23 15/16 in. (12.5 to 600 mm) in width, inclusive. Strip tolerance products may be available in widths wider than 2315/16 in. (600 mm) by agreement between purchaser and supplier; however, such products are technically classified as cold-rolled sheet.1.2 The maximum of the specified carbon range is over 0.25 % to 1.35 %, inclusive. 1.3 The above shall apply to the cold-rolled carbon spring steel strip furnished under each of the following specifications issued by ASTM:Title of Specification ASTM DesignationSteel, Strip, High Carbon,A 684/A 684MCold Rolled 1.4 The tolerances in this specification are different than those in Specification A 568/A 568M and Specification A 109/A 109M.1.5 For the purpose of determining conformance with this specification, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29.1.6 The metric portions of the tables herein list permissible variations in dimensions and mass (see Note 1) in SI (metric) units. The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the "M" specification is used.Note 18212;The term weight is used when inch-pound units are the standard. However, under SI the preferred term in mass.1.7 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems will result in nonconformance with the specification.1.8 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.

Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled, General Requirements For

EN 10089:2002 淬火和回火热轧弹簧钢.交货技术条件

This European Standard specifies the technical delivery requirements for round and flat bars,ribbed and grooved bars and rod manufactured from the alloy steels listed in Table 3,intended for hot-formed and subsequently heat-treated springs or cold-formed and subsequently heat-treated springs.

Hot-rolled steels for quenched and tempered springs - Technical delivery conditions

EN 10151:2002 弹簧用不锈钢带材.交货技术条件

This European Standard applies to cold rolled narrow strip of thicknesses up to and including 3 mm in rolled widths less than 600 mm made from the stainless steel grades listed in Table 1.The steels are used in the conditions given in Table 4 for the production of springs and spring parts that are exposed to corrosive effects andsometimes slightly increased temperatures.

Stainless steel strip for springs - Technical delivery conditions

ASTM A313/A313M-98 不锈钢弹簧丝标准规格

1.1 This specification covers austenitic and age-hardenable stainless steel round spring wire intended especially for the manufacture of springs. 1.2 The values stated in inch-pound units or SI units are to be regarded separately as the standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 Unless the order specifies an "M" designation, the material shall be furnished to inch-pound units.

Standard Specification for Stainless Steel Spring Wire

DLA MIL-W-21425 B NOTICE 1-1997 机械弹簧方未上漆的高碳钢圈

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

WIRE, STEEL, HIGH CARBON, SQUARE UNCOATED FOR MECHANICAL SPRINGS [Superseded: SAE AMS-W-21425B, SAE AMS-W-21425A, SAE AMS-W-21425]

ANSI/ASTM B471:1996 UNS NO8020、UNS NO8026和UNS NO8024镍合金弹簧丝规范

Specification for UNS N08020, UNS N08026, and UNS N08024 Nickel Alloy Spring Wire

JIS G 4313:1996 弹簧用冷轧不锈钢带

この規格は，主として自動車，電気機器などに使用される薄板ばね，ぜんまいばねに用いるステンレス鋼帯（以下，帯という。)について規定する。

Cold rolled stainless steel strip for springs

ASTM A764-95(2001) 金属涂层碳钢丝的标准规格 尺寸涂层 尺寸为机械弹簧

Standard Specification for Metallic Coated Carbon Steel Wire, Coated at Size and Drawn to Size for Mechanical Springs

JIS G 4314:1994 弹簧用不锈钢丝

この規格は，ばね用ステンレス鋼線(以下，線という。)について規定する。

Stainless steel wires for springs

SAE J217-1994 不锈钢17-7 PH 弹簧钢丝和弹簧

This SAE Recommended Practice covers a high-quality corrosion resisting steel wire, cold drawn, formed, and heat treated to produce uniform mechanical properties. It is magnetic in all conditions. It is intended for the manufacture of springs and wire forms that are to be heat treated after forming to enhance the spring properties. This document covers basic processing requirements of springs and forms fabricated from this wire.

Stainless Steel 17-7 PH Spring Wire and Springs