共找到 143 条与 弹簧钢 相关的标准,共 10 页
Applies to the steel grades listed in table 1, which are generally used in the work-hardened condition in the form of wire up to about 6 mm in diameter. The produced springs are exposed to corrosive effects and sometimes slightly increased temperatures.
Stainless steels for springs - Part 1: Wire
この規格は,内燃機関の弁ばね又はこわに準じろばねに使用されるオィルテンパ一線(以下,線という。)について規定する。
Oil tempered wire for valve springs
この規格は,一般のばねに使用されるオィルテンパ一線(以下,線という。)について規定する。
Oil tempered wire for mechanical springs
This SAE Recommended Practice covers a high-strength corrosion-resisting steel wire, uniform in mechanical properties, intended for the manufacture of springs and wire forms. It covers processing requirements of springs and forms fabricated from this wire.
(R) Stainless Steel, SAE 30302, Spring Wire and Springs June 1994
Настоящий стандарт устанавливает общие требования, предъявляемые к стальной пружинной проволоке круглого сечения без покрытия, предназн
Steel wire for mechanical springs. General requirements
1.1 This specification covers round, uncoated, cold-drawn spring wire in coils having properties and quality intended for the manufacture of the following upholstery springs: 1.1.1 Type A8212;Zig-zag (U-formed), 1.1.2 Type B8212;Square-formed, and 1.1.3 Type C8212;Sinuous for furniture spring units. 1.2 These types of upholstery springs are used in the manufacture of automotive seat springs and furniture springs. The wire is not intended for the manufacture of mechanical springs.
Standard Specification for Steel Wire, Cold-Drawn, for Zig-Zag, Square-Formed, and Sinuous-Type Upholstery Spring Units
Настоящий стандарт устанавливает требования, предъявляемые к холоднотянутой проволоке из углеродистой стали, предназначенной для изгот
Steel wire for mechanical springs cold-drown carbon steel wire
Steel wire for mechanical springs; part 3: oil-hardened and tempered wire
Heat-treatable steels, alloy steels and free-cutting steels; part 14: hot-rolled steels for quenched and tempered springs
Specification for patented cold drawn steel wire for mechanical springs
Steel wire for mechanical springs; part 2: cold-drawn carbon steel wire
Steel wire for mechanical springs; part 1: general requirements
Applies to hot-rolled spring steel with the dimensions stated in table 1, of the steel grades listed in clause 4, which are preferably used for rail vehicle construction. Specifies dimensions and tolerances, material, mode of delivery and testing.
Steel; hot-rolled ribbed and grooved flats for spring leaves; tolerances and dimensions
Steel strip intended for the manufacture of springs - Specification for martensitic and austenitic stainless steel
Requirements for annealed or annealed and lightly drawn wire suitable for the manufacture of mechanical springs by cold forming, that are subsequently hardened and tempered.
Specification for annealed round steel wire for general engineering springs
Настоящий стандарт распространяется на стальную холоднокатаную ленту, предназначенную для изготовления пружин, измерительных лент и дру
Cold-rolled tool and spring steel strip. Specifications
This specification covers three types of uncoated, squake (0.050 to 0.500 inches in width), high-carbon steel wire (see 6.1).
WIRE, STEEL, HIGH CARBON, SQUARE UNCOATED FOR MECHANICAL SPRINGS
Heat-treated steels, alloy steels and free-cutting steels — Part 14: Steels for hot-formed and heat-treated springs
Requirements for patented cold drawn plain carbon steel round wire; chemical composition, standard sizes and tolerances, methods of testing and mechanical properties, including tensile strength ranges, and packing and identification data.
Specification for carbon steel wire for coiled springs (bedding and seating)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号