77.150.40 镍和铬产品 标准查询与下载

ASTM B167-23 镍铬铝合金、镍铬铁合金、镍铬钴钼合金、镍铁铬钨合金和镍铬钼铜合金无缝管标准规范

Standard Specification for Nickel-Chromium-Aluminum Alloys, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Co

ASTM B444-23 镍铬钼铌合金和镍铬钼硅合金管材标准规范

1.1 This specification2 covers nickel-chromiummolybdenum-niobium alloys (UNS N06625 and UNS N06852) and nickel-chromium-molybdenum-silicon alloy (UNS N06219)3 in the form of cold-worked seamless pipe and tube. The general requirements for pipe and tube are covered by Specification B829. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. X1.1 Scope X1.1.1 This appendix lists the conditions and finishes in which pipe and tube (other than converter sizes) are normally supplied. These are subject to change, and the manufacturer should be consulted for the latest information available. X1.2 Cold-Worked Tube and Pipe X1.2.1 Cold–Drawn, Annealed or Solution Annealed with Ground Outside Diameter—The inside diameter may have a bright finish when material is annealed or solution annealed in a protective atmosphere; otherwise, the inside diameter is supplied descaled as necessary. It is available in sizes 1⁄2 in. to 4 in. (12.7 mm to 102 mm), incl, in outside diameter in both normal and heavy-wall tube, and pipe sizes, all schedules, of corresponding outside-diameter dimensions. X1.2.2 Cold–Drawn, Annealed or Solution Annealed and Pickled (Not Ground)—Outside and inside diameter will have dull, matte (pickled) surfaces. Available in sizes 1⁄2 in. to 65⁄8 in. (12.7 mm to 168 mm), incl, in outside diameter in both normal and heavy-wall tube, and pipe sizes, all schedules, of corresponding outside-diameter dimensions. SUMMARY OF CHANGES Committee B02 has identified the location of selected changes to this standard since the last issue (B444 – 18) that may impact the use of this standard. (Approved July 1, 2023.) (1) Revised Title. (2) Added Terminology Section and B899 to Referenced Documents section. (3) Added Materials and Manufacture section. Relocated General Requirements and Scope information to this section. (4) Changed light wall tube to tube with specified wall thickness 3 % or less of the specified outside diameter for converter sizes. (5) Deleted Dimensions and Permissible Variations section. (6) Moved converter sizes from Appendix to Annex. (7) Deleted Number of Tests section and addressed requirements under specific test. (8) Changes Columbium to Niobium in 1.1 and Table 2 and added equivalency footnote. (9) Updated Ordering Information references. (10) Revised 8.1. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website (www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http://www.copyright.com/ B444 − 23 5 

Standard Specification for Nickel-Chromium-Molybdenum-Niobium Alloys and Nickel-Chromium-Molybdenum-Silicon Alloy Pipe and Tube

ASTM B805-23 沉淀硬化镍合金棒材和线材标准规范

1.1 This specification covers nickel alloys UNS N07716, N07725, N07773, N07776, N09777, and N09925 in the form of hot or cold finished rounds, squares, hexagons, rectangles, and cold finished wire. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods, portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Precipitation Hardening Nickel Alloys Bar and Wire

ASTM B575-17(2023) 低碳镍铬钼、低碳镍铬钼铜、低碳镍铬钼钽、低碳镍铬钼钨和低碳镍钼铬合金板、薄板和带材的标准规范

1.1 This specification2 covers plate, sheet, and strip of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06455, N06035, N06044, UNS N06058, UNS N06059),3 low-carbon nickel-chromium-molybdenumcopper alloy (UNS N06200), low-carbon nickel-molybdenumchromium (UNS N10362), low-carbon nickel-chromiummolybdenum-tantalum alloy (UNS N06210), and low-carbon nickel-chromium-molybdenum-tungsten alloy (UNS N06686) as shown in Table 1, for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip—Hot or cold rolled, solution annealed, and descaled unless solution anneal is performed in an atmosphere yielding a bright finish. 1.2.2 Plate—Hot or cold rolled, solution annealed, and descaled. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tu

ASTM B581-17(2023) 镍铬铁钼铜合金棒的标准规范

1.1 This specification2 covers rod of Ni-Cr-Fe-Mo-Cu alloys (UNS N06007, N06975, N06985, N06030, N08031, and N08034)3 as shown in Tables 1-3, for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Rods 5⁄16 in. to 3⁄4 in. (7.94 mm to 19.05 mm) excl in diameter, hotor cold-finished, solution annealed and pickled or mechanically descaled. 1.2.2 Rods 3⁄4 in. to 31⁄2 in. (19.05 mm to 88.9 mm) incl in diameter, hotor cold-finished, solution annealed, ground or turned. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod

ASTM B739-03(2023) 镍铁铬硅合金焊接管标准规范

1.1 This specification covers alloys UNS N08330 and UNS N08332 in the form of welded tube intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Tube

T/CNIA 0200-2023 绿色设计产品评价技术规范 镍钴二元素复合氢氧化物

本文件规定了镍钴二元素复合氢氧化物绿色设计产品评价的评价要求、生命周期评价（LCA）报告编制方法、评价方法和流程。 本文件适用于锂离子电池正极材料前驱体镍钴二元素复合氢氧化物的绿色设计产品评价。

Technical specifications for green design product evaluation Nickel-cobalt di-element composite hydroxide

ASTM B434-22 镍钼铬铁合金板、薄板和带材

1.1 This specification2 covers nickel-molybdenumchromium-iron alloys in the form of plate, sheet, and strip. The alloys are typically for general corrosive service, but are not limited to this usage. 1.2 Alloys that can currently be certified to this specification are UNS N10003 and UNS N10242.3 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Molybdenum-Chromium-Iron Alloys Plate, Sheet, and Strip

ASTM B535-06(2022) 镍铁铬硅合金（UNS N08330和N08332）无缝管

1.1 This specification2 covers alloys UNS N08330 and N08332 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube

ASTM B409-22 镍铁铬合金板、薄板和带材标准规范

1.1 This specification2 covers UNS N08120, UNS N08890, UNS N08800, UNS N08810, and UNS N088113 in the form of rolled plate, sheet, and strip. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100 °F (593 °C). Alloys UNS N08120, UNS N08810, UNS N08811, and UNS N08890 are normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture is required, and they are annealed to develop controlled grain size for optimum properties in this temperature range. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium Alloy Plate, Sheet, and Strip

ASTM B424-22 镍铁铬钼铜合金板、薄板及带材

1.1 This specification2 covers rolled nickel-iron-chromiummolybdenum-copper alloys (UNS N08642, UNS N06845, UNS N08221, UNS N08825, and UNS N08827) plate, sheet, and strip. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloys Plate, Sheet, and Strip

YS/T 1516-2022 高纯镍铸锭

本文件适用于半导体溅射靶材、蒸发料等所需的高纯镍铸锭。

High purity nickel ingot

KS D 6023-2022 镍及镍合金铸件

Nickel and nickel alloy castings

ASTM B906-22 平轧镍和镍合金板材、薄板和带材的一般要求标准规范

1.1 This specification covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled nickel and nickel alloy plate, sheet, and strip, under each of the following specifications issued by ASTM: Specifications B127, B162, B168, B333, B409, B424, B434, B435, B443, B463, B536, B575, B582, B599, B620, B625, B670, B688, B709, B718, B755, B814, B818, B872. 1.2 In case of any conflicting requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip

T/ZZB 2775-2022 锂离子电池用镍钴锰三元素复合氢氧化物

本文件规定了锂离子电池用镍钴锰三元素复合氢氧化物的分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书、订货单（或合同）内容和质量承诺。 本文件适用于以硫酸镍、硫酸钴、硫酸锰为主要原料经合成反应制成的锂离子电池用镍钴锰三元素复合氢氧化物，以下简称NCM。

Nickel cobalt manganese composite hydroxide for lithium ion batteries

GSO ASTM F2633:2022 医疗器械和外科植入物用锻造无缝镍钛形状记忆合金管的标准规范

This specification covers the chemical, mechanical, and dimensional requirements for wrought seamless nickel-titanium shape memory alloy tubes used for the manufacture of medical devices and surgical implants. Tubes shall be furnished in the superelastic condition, and the outer surface shall have a pickled, ground, or mechanically polished finish, or as agreed upon between purchaser and supplier. This specification addresses those product variables that differentiate drawn medical grade tube from the raw material and mill product forms. This specification applies precisely to tube with 10 mm (0.4 in.) and smaller nominal outside diameter and 2 mm (0.08 in.) and thinner nominal wall thickness. The mechanical properties to which the tubes shall conform are ultimate tensile strength (UTS), uniform elongation, upper plateau strength, lower plateau strength, and residual elongation.

Standard Specification for Wrought Seamless Nickel-Titanium Shape Memory Alloy Tube for Medical Devices and Surgical Implants

ASTM B408-22 镍铁铬合金棒材的标准规范

1.1 This specification2 covers UNS N08120, UNS N08800, UNS N08810, UNS N08811,3 and UNS N08890 in the form of hot-worked and cold-worked rod and bar. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100 °F (593 °C). Alloys UNS N08120, UNS N08810, UNS N08811, and UNS N08890 are normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture is required, and they are annealed to develop controlled grain size for optimum properties in this temperature range. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium Alloy Rod and Bar

T/ATCRR 44-2022 粗制镍钴锰氢氧化物

粗制镍钴锰氢氧化物

Crude nickel cobalt manganese hydroxide

ASTM B564-22 镍合金锻件标准规范

1.1 This specification2 covers forgings of: Alloy Type UNS Number(s) Fe-Ni-Cr-Mo-N N08367 Low-carbon Cr-Ni-Fe-N R20033 Low-carbon Ni-Cr-Mo N06035, N06058, N06059, N06044 Low-carbon Ni-Cr-Mo-Cu N06200 Low-carbon Ni-Cr-Mo-W N06686 Low-carbon Ni-Fe-Cr-Mo-Cu N08031, N08034 Low-carbon Ni-Mo-Cr N10276, N06022, N10362 Low-carbon Ni-Mo-Cr-Ta N06210 Ni N02200 Ni-Co-Cr-Si N12160 Ni-Cr-Al N06699 Ni-Cr-Co-Mo N06617 Ni-Cr-Fe N06600, N06603, N06690 Ni-Cr-Fe-Al N06025 Ni-Cr-Fe-Si N06045 Ni-Cr-Mo-Nb N06625 Ni-Cr-Mo-Si N06219 Ni-Cr-Mo-W N06110 Ni-Cr-W-Mo N06230 Ni-Cu N04400 Ni-Fe-Cr N08120, N08800, N08810, N08811 Ni-Fe-Cr-Mo-Cu N08825, N08827 Ni-Fe-Cr-W N06674 Ni-Mo N10665, N10675, N10629 Ni-Mo-Cr-Fe N10242, N10624 1.1.1 The nickel-iron-chromium alloys are UNS N08120, UNS N08800, UNS N08810, and UNS N08811. Alloy UNS N08800 is normally employed in service temperatures up to and including 1100 °F (593 °C). Alloys UNS N08810, N08120, and UNS N08811 are normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture is required, and are annealed to develop controlled grain size for optimum properties in this temperature range. 1.1.2 Nickel-iron-chromium-tungsten alloy UNS N06674 is normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture is required, and is annealed to develop optimum properties in this temperature range. 1.1.3 Nickel-chromium-molybdenum-columbium (UNS N06625) products are furnished in two grades of different heat-treated conditions: 1.1.3.1 Grade 1 (Annealed)—Material is normally employed in service temperatures up to 1100 °F (593 °C). 1.1.3.2 Grade 2 (Solution annealed)—Material is normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture are required. NOTE 1—Hot-working or reannealing may change properties significantly, depending on working history and temperatures. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel Alloy Forgings

ASTM B718-22 镍铬钼钴钨铁硅合金板的标准规范

1.1 This specification covers wrought alloy UNS N06333 plate intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy Plate