77.150.40 镍和铬产品 标准查询与下载

ASTM B718-22 镍铬钼钴钨铁硅合金板的标准规范

1.1 This specification covers wrought alloy UNS N06333 plate intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy Plate

ASTM A494/A494M-22 镍及镍合金铸件标准规范

1.1 This specification covers nickel, nickel-copper, nickelcopper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium alloy castings for corrosionresistant service. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Castings, Nickel and Nickel Alloy

YS/T 717-2021 雾化镍粉

Atomized nickel powder

ASTM B621-21 镍铁铬钼合金棒的标准规范

1.1 This specification2 covers nickel-iron chromiummolybdenum alloy (UNS N08320)3 rod for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Rods 5⁄16 to 3⁄4 in. (7.94 to 19.05 mm) excl in diameter, hot or cold finished, solution annealed and pickled or mechanically descaled. 1.2.2 Rods 3⁄4 to 31⁄2 in. (19.05 to 88.9 mm) incl in diameter, hot or cold finished, solution annealed, ground or turned. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Molybdenum Alloy Rod

ASTM B511/B511M-21 镍铁铬硅合金棒材和型材的标准规范

1.1 This specification2 covers wrought alloys UNS N08330 and UNS N08332 in the form of hot-finished and cold-finished bar and shapes intended for heat-resisting applications and general corrosive service. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Bars and Shapes

ASTM B625-21 Ni-Fe-Cr-Mo-Cu-N低碳合金、Ni-Fe-Cr-Si合金、Cr-Ni-Fe-N低碳合金、Fe-Ni-Cr-Mo-Cu-N合金和Ni-Fe-Cr-Mo-N合金板材、薄板和带材的标准规范

1.1 This specification covers nickel-iron-chromiummolybdenum-copper-nitrogen low-carbon alloy, nickel-ironchromium-silicon alloy, chromium-nickel-iron-nitrogen lowcarbon alloy, iron-nickel-chromium-molybdenum-coppernitrogen alloy, and nickel-iron-chromium-molybdenumnitrogen alloy plate, sheet, and strip in the annealed temper. 1.2 ASTM International has adopted definitions whereby some grades, such as UNS N08904, previously in this specification were recognized as stainless steels, because those grades have iron as the largest element by mass percent. Such grades are under the oversight of ASTM Committee A01 and its subcommittees. The products of N08904 previously covered in this specification are now covered by Specifications A240/ A240M and A480/A480M. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy, Ni-Fe-Cr-Si Alloy, Cr-Ni-Fe-N Low-Carbon Alloy, Fe-Ni-Cr-Mo-Cu-N Alloy, and Ni-Fe-Cr-Mo-N Alloy Plate, Sheet, and Strip

ASTM B649-21 Ni-Fe-Cr-Mo-Cu-N低碳合金和Cr-Ni-Fe-N低碳合金棒材和线材、Ni-Cr-Fe-Mo-N合金线材和Ni-Fe-Cr-Mo-N合金棒材的标准规范

1.1 This specification covers nickel-iron-chromiummolybdenum-copper-nitrogen alloy and chromium-nickeliron-nitrogen low-carbon alloy bar and wire, nickel-chromiumiron-molybdenum-nitrogen alloy wire, and nickel-ironchromium-molybdenum-nitrogen alloy bar. 1.2 ASTM International has adopted definitions whereby some grades, such as UNS N08904,2 previously in this specification were recognized as stainless steels, because those grades have iron as the largest element by mass percent. Such grades are under the oversight of ASTM Committee A01 and its subcommittees. The products of N08904 previously covered in this specification are now covered by Specifications A479/ A479M and A484/A484M. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy and Cr-Ni-Fe-N Low-Carbon Alloy Bar and Wire, Ni-Cr-Fe-Mo-N Alloy Wire, and Ni-Fe-Cr-Mo-N Alloy Bar

ASTM F3055-14a(2021) 粉末层熔合添加剂制造镍合金（UNS N07718）的标准规范

1.1 This specification covers additively manufactured UNS N07718 components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured UNS N07718 components for defining the requirements and ensuring component properties. 1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Supplementary Requirements S1–S16. 1.5 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion

ASTM B630-88(2021) 铬电镀用铬的制备标准实施规程

1.1 This practice is intended to serve as a process guide (not as a standard procedure) for producing adherent electrodeposits of chromium on chromium for engineering use. 1.2 Only well-known, generally practical methods using hexavalent chromium plating baths have been included. Some of the newer proprietary chromium plating processes produce chromium plating for which this process is unsuitable. Suppliers of the processes should be consulted. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Chromium for Electroplating with Chromium

ASTM F3056-14(2021) 粉末层熔合添加剂制造镍合金（UNS N06625）的标准规范

1.1 This specification covers additively manufactured UNS N06625 components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured UNS N06625 components for defining the requirements and ensuring component properties. 1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Supplementary Requirements S1–S16. 1.5 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion

T/ZZB 2407-2021 单晶正极材料用镍钴锰三元素复合氢氧化物

本文件规定了单晶正极材料用镍钴锰三元素复合氢氧化物的术语和定义、分类、基本要求、技术要求、试验方法、检验规则、包装、标志、运输、贮存、质量证明书和质量承诺。 本文件适用于单晶正极材料用镍钴锰三元素复合氢氧化物，其化学式为 NixCoyMn1-x-y(OH)2（其中 x＋y＜1， x＞0 且 y＞0）。

Nickel cobalt manganese composite hydroxide applied in single crystal cathode material

T/CNEA 101.40-2021 压水堆承压部件 材料 第40部分：高温用沉淀硬化镍合金棒材、锻件和锻坯

本文件是T/CNEA 101《压水堆承压部件 材料》的第40部分。本文件共计14章，其中，1-3章为规范性条款，4-14章为压水堆承压部件 材料 第40部分：高温用沉淀硬化镍合金棒材、锻件和锻坯主要内容。主要内容包括：订货要求、化学成分、尺寸和允许偏差、工艺质量、表面质量和外观、试验材料选择、力学性能、试样准备、试验方法、检验、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 40:Precipitation hardening nickel alloy bars, forgings and forging stocks for high-temperature service

T/CNEA 101.38-2021 压水堆承压部件 材料 第38部分：镍-铬-铁合金锻件

本文件是T/CNEA 101《压水堆承压部件 材料》的第38部分。本文件共计15章，其中，1-3章为规范性条款，4-15章为压水堆承压部件 材料 第38部分：镍-铬-铁合金锻件主要内容。主要内容包括：订货要求、化学成分、力学性能、尺寸和允许偏差、工艺质量、表面质量和外观、取样、试验数量、试样制备、试验方法、检验、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 38:Nickel-chromium-iron alloy forgings

T/CNEA 101.39-2021 压水堆承压部件 材料 第39部分：镍-铬-铁合金棒材和线材

本文件是T/CNEA 101《压水堆承压部件 材料》的第39部分。本文件共计15章，其中，1-3章为规范性条款，4-15章为压水堆承压部件 材料 第39部分：镍-铬-铁合金棒材和线材主要内容。主要内容包括：订货要求、化学成分、力学性能、尺寸和允许偏差、工艺表面、表面质量和外观、取样、试验数量、试样准备、试验方法、检验、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 39:Nickel-chromium-iron alloys bars and wires

T/CNEA 101.36-2021 压水堆承压部件 材料 第36部分：镍-铬-铁无缝合金管

本文件是T/CNEA 101《压水堆承压部件 材料》的第36部分。本文件共计16章，其中，1-3章为规范性条款，4-16章为压水堆承压部件 材料 第36部分：镍-铬-铁无缝合金管主要内容。主要内容包括：订货要求、化学成分、力学性能、水压试验或无损检测、尺寸和允许偏差、工艺质量、表面质量和外观、取样、试验数量、试样准备、试验方法、检验、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 36:Nickel-chromium-iron alloys seamless pipes and tubes

T/CNEA 101.37-2021 压水堆承压部件 材料 第37部分：镍-铬-铁合金板、薄板和带材

本文件是T/CNEA 101《压水堆承压部件 材料》的第37部分。本文件共计16章，其中，1-3章为规范性条款，4-16章为压水堆承压部件 材料 第37部分：镍-铬-铁合金板、薄板和带材主要内容。主要内容包括：订货要求、化学成分、力学性能、深冲和旋压的薄板和带材、尺寸和允许偏差、工艺质量、表面质量和外观、取样、试验数量、试样准备、试验方法、检验、质量证明文件和产品标志。

PWR pressure boundary components—Material— Part 37:Nickel-chromium-iron alloys plates, sheets, and strips

DIN 17750:2021 锻造镍和镍合金的带材和板材. 特性

This standard specifies the mechanical properties of strips and sheets of nickel and wrought nickel alloys for the dimensional ranges given in table 1.

Strips and sheets of wrought nickel and nickel alloys - Properties

ASTM B673-21 镍铁铬钼和铁镍铬钼铜焊管标准规范

1.1?This specification covers UNS N08925, UNS N08354, and UNS N089262 welded pipe for general corrosion applications. 1.2?This specification covers pipe sizes in schedules shown in Table 1. 1.3?ASTM International has adopted definitions whereby some grades, such as UNS N08904

Standard Specification for Nickel-Iron-Chromium-Molybdenum and Iron-Nickel-Chromium-Molybdenum-Copper Welded Pipe

YS/T 1370-2020 钛合金用钛锡中间合金

Titanium-tin master alloy for titanium alloys

YS/T 1369-2020 钛合金用镍钼中间合金

Nickel-molybdenum master alloy for titanium alloys