77.150.40 镍和铬产品 标准查询与下载

YS/T 1220-2018 铬靶材

Chromium target

YS/T 1228-2018 粗氢氧化镍

Crude nickel hydroxide

YS/T 1219-2018 草酸镍

Nickel oxalate

ASTM A560/A560M-12(2018) 铬镍合金铸件标准规范

1.1 This specification covers chromium-nickel alloy castings intended for heat-resisting and elevated-temperature corrosion applications, such as structural members, containers, supports, hangers, spacers, and the like, in corrosive environments up to 2000 °F [1090 °C]. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Castings, Chromium-Nickel Alloy

ASTM A494/A494M-17a 镍和镍合金铸件的标准规范

Standard Specification for Castings, Nickel and Nickel Alloy

ASTM B575-17 低碳镍铬钼、低碳镍铬钼铜、低碳镍铬钼钽、低碳镍铬钼钨和低碳镍钼铬合金板、薄板和带材的标准规范

1.1 This specification2 covers plate, sheet, and strip of low-carbon nickel-chromium-molybdenum alloys (UNS N10276, N06022, N06455, N06035, N06044, UNS N06058, UNS N06059),3 low-carbon nickel-chromium-molybdenumcopper alloy (UNS N06200), low-carbon nickel-molybdenumchromium (UNS N10362), low-carbon nickel-chromiummolybdenum-tantalum alloy (UNS N06210), and low-carbon nickel-chromium-molybdenum-tungsten alloy (UNS N06686) as shown in Table 1, for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Sheet and Strip—Hot or cold rolled, solution annealed, and descaled unless solution anneal is performed in an atmosphere yielding a bright finish. 1.2.2 Plate—Hot or cold rolled, solution annealed, and descaled. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tu

ASTM B574-17 低碳镍铬钼、低碳镍钼铬、低碳镍钼铬钽、低碳镍铬钼铜和低碳镍铬钼钨合金棒的标准规范

1.1 This specification2 covers rod of low-carbon nickelchromium-molybdenum alloys (UNS N10276, N06022, N06035, N06044, N06455, N06058, and N06059), low-carbon nickel-molybdenum-chromium (USN N10362), low-carbon nickel-molybdenum-chromium-tantalum (UNS N06210), lowcarbon nickel-chromium-molybdenum-copper alloy (UNS N06200), and low-carbon nickel-chromium-molybdenumtungsten (UNS N06686) as shown in Table 1, for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Rods 5⁄16 to 3⁄4 in. (7.94 to 19.05 mm), exclusive, in diameter, hot or cold finished, solution annealed and pickled, or mechanically descaled. 1.2.2 Rods 3⁄4 to 31⁄2 in. (19.05 to 88.9 mm), inclusive, in diameter, hot or cold finished, solution annealed, ground or turned. 1.2.3 Rods 1⁄4 to 3 1⁄2 in. (6.35 to 88.9 mm), inclusive, in diameter, solution annealed, cold finished, as cold finished, ground or turned (N06059 and N06686 only, see Table 2 and Table 3). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, a

ASTM B564-17 镍合金锻件的标准规范

Standard Specification for Nickel Alloy Forgings

ISO 9725:2017 镍和镍合金锻件

This document specifies requirements for nickel and nickel alloy forgings for general purposes.

Nickel and nickel alloy forgings

ASTM B630-88(2017) 用铬电镀制备铬的标准实践

1.1 This practice is intended to serve as a process guide (not as a standard procedure) for producing adherent electrodeposits of chromium on chromium for engineering use. 1.2 Only well-known, generally practical methods using hexavalent chromium plating baths have been included. Some of the newer proprietary chromium plating processes produce chromium plating for which this process is unsuitable. Suppliers of the processes should be consulted. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Preparation of Chromium for Electroplating with Chromium

NB/T 20008.33-2017 压水堆核电厂用其他材料 第33部分：控制棒驱动机构用GH5605合金棒

Other materials for pressurized water reactor nuclear power plants Part 33: GH5605 alloy rods for control rod driving mechanisms

NB/T 20008.32-2017 压水堆核电厂用其他材料 第32部分：控制棒驱动机构用NS3306合金板材及带材

Other materials for pressurized water reactor nuclear power plants Part 32: NS3306 alloy plates and strips for control rod driving mechanisms

ASTM B535-06(2017) 镍 - 铁 - 铬 - 硅合金标准规格（UNS N08330和N08332）无缝管和管

1.1 This specification2 covers alloys UNS N08330 and N08332 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat resisting applications and general corrosive service. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and N08332) Seamless Pipe and Tube

ASTM B805-06(2017)e1 沉淀硬化镍合金棒和线的标准规范

1.1 This specification covers nickel alloys UNS N07716, N07725, N07773, N07776, N09777, and N09925 in the form of hot or cold finished rounds, squares, hexagons, rectangles, and cold finished wire. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods, portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Precipitation Hardening Nickel Alloys Bar and Wire

NB/T 20008.28-2017 压水堆核电厂用其他材料 第28部分：安全级设备用NS3105合金锻件

Other materials for pressurized water reactor nuclear power plants Part 28: NS3105 alloy forgings for safety grade equipment

NB/T 20008.30-2017 压水堆核电厂用其他材料 第30部分：安全级设备用NS3105合金管

Other materials for pressurized water reactor nuclear power plants Part 30: NS3105 alloy tubes for safety grade equipment

NB/T 20008.31-2017 压水堆核电厂用其他材料 第31部分：安全级设备用NS3105合金棒

Other materials for pressurized water reactor nuclear power plants Part 31: NS3105 alloy rods for safety grade equipment

NB/T 20008.29-2017 压水堆核电厂用其他材料 第29部分：安全级设备用NS3105合金板材及带材

Other materials for pressurized water reactor nuclear power plants Part 29: NS3105 alloy sheets and strips for safety grade equipment

ASTM A494/A494M-17 镍和镍合金铸件的标准规格

1.1 This specification covers nickel, nickel-copper, nickel-copper-silicon, nickel-molybdenum, nickel-chromium, and nickel-molybdenum-chromium alloy castings for corrosion-resistant service. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

Standard Specification for Castings, Nickel and Nickel Alloy

GSO ISO 9725:2016 镍及镍合金锻件

This International Standard specifies requirements for nickel and nickel alloy forgings for general purposes. NOTE 1 Bars used for the manufacture of forgings should conform to the requirements for bars to be further worked by the purchaser, specified in subclause 5.2 of ISO 9723:1992.

Nickel and nickel alloy forgings