81.040.20 建筑玻璃 标准查询与下载

ASTM C1376-21a 平板玻璃上热解和真空沉积涂层的标准规范

1.1 This specification covers the optical and aesthetic quality requirements for pyrolytic and vacuum deposition coatings applied on flat glass for use in building glazing. 1.2 The coatings are applied on the glass using either pyrolytic or vacuum sputtering deposition methods to control solar heat gain, energy performance, comfort level, and condensation and to enhance the aesthetic of the building. 1.3 This specification addresses blemishes related to the coating only. It does not address glass blemishes, applied ceramic frits to spandrel glass, and organic film opacifiers. 1.4 The Nonuniformity for Coated Glass requirements, given in 6.10, pertain to glazing units of vertical and sloped orientations as installed in the building exterior. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass

UNI 7697-2021 玻璃应用的安全标准

Safety criteria for glazing applications

DS/ISO/TS 21480:2021 建筑玻璃—建筑一体化光伏组件回收通用技术要求

Glass in building – General technical requirements of building integrated photovoltaic modules recycling

ISO/TS 21480:2021 建筑玻璃.建筑集成光伏组件回收的一般技术要求

Glass in building — General technical requirements of building integrated photovoltaic modules recycling

PN-EN 1279-6-2018-08 P 建筑玻璃 中空玻璃单元 第6部分：工厂生产控制和定期测试

Glass in building -- Insulating glass units -- Part 6: Factory production control and periodic tests

OENORM B 3716-2-2021 建筑玻璃 结构玻璃结构 第2部分：线性玻璃窗

Glass in building - Structural glass construction - Part 2: Linear glazings

OENORM B 3716-1-2021 建筑玻璃 结构玻璃结构 第1部分：基本原理

Glass in building - Structural glass construction - Part 1: Basic principles

ASTM E997-15(2021) 通过验证载荷试验评估均匀静载荷影响下玻璃破碎概率的标准试验方法

1.1 This proof load test method is a procedure to determine, with a 90 % confidence level, if the probability of breakage under design loads for a given population of glass specimens is less than a selected value. It is not intended to be a design standard for determining the load resistance of glass. Practice E1300 shall be used for this purpose. 1.2 This test method describes apparatus and procedures to select and apply a proof load to glass specimens, to determine the number of glass specimens to be tested, and to evaluate statistically the probability of breakage. This test method may be conducted using the standard test frame specified herein or a test frame of the user’s design. 1.3 Proper use of this test method requires a knowledge of the principles of pressure measurement and an understanding of recommended glazing practices. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Evaluating Glass Breakage Probability Under the Influence of Uniform Static Loads by Proof Load Testing

EN 16759:2021 门窗和幕墙用粘合玻璃 铝和钢表面粘合的机械性能验证

Bonded Glazing for doors, windows and curtain walling - Verification of mechanical performance of bonding on aluminium and steel surfaces

FprEN ISO 12543-5:2021 建筑玻璃 夹层玻璃和夹层安全玻璃 第5部分：尺寸和边缘修整（ISO/FDIS 12543-5:2021）

Glass in building - Laminated glass and laminated safety glass - Part 5: Dimensions and edge finishing (ISO/FDIS 12543-5:2021)

GSO ASTM C1036:2021 平板玻璃标准规范

This specification covers the quality requirements of flat, transparent, clear, and tinted glass. This glass is intended to be used primarily for architectural glazing products including: coated glass, insulating glass units, laminated glass, mirrors, spandrel glass, or similar uses. The monolithic flat glass shall be supplied as cut sizes or stock sheets. Two types of glasses shall be used: Type I which is a transparent flat glass and Type II which is a patterned and wired flat glass. Type II glass shall have clear and tinted classes while Type I glass shall only have the clear class. Different test methods for Type I glass shall be performed in order to determine the following properties: point blemish and linear blemish content, ream distortion, string distortion, line distortion, dimension, squareness, reflectance, and transmittance. As for the type II glass the following properties shall be determined after different tests: associated distortion and blemish appraisal, dimension, point blemish, reflectance, and transmittance.

Standard Specification for Flat Glass

GSO ISO 1288-5:2021 建筑用玻璃 玻璃抗弯强度的测定 第5部分：小试验表面积平板试样的同轴双环试验

ISO 1288-5:2016 specifies a method for determining the comparative bending strength of glass for use in buildings, excluding the effects of the edges. See ISO 1288‑1, 5.1.4 for an explanation as to why this test method should only be used for comparing the strength of types of glass and not for assessing strength for design purposes. The limitations of this part of ISO 1288 are described in ISO 1288‑1. ISO 1288‑1 should be read in conjunction with this part of ISO 1288. This test method is not suitable for patterned glass.

Glass in building — Determination of the bending strength of glass — Part 5: Coaxial double ring test on flat specimens with small test surface areas

GSO ASTM C1464:2021 弯曲玻璃的标准规范

This specification covers the standard for bent glass proposed for use in general building construction, furniture, display, and various other non-automotive applications. When the glass is specified as chemically strengthened, heat-strengthened, or fully tempered, the fabrication processes must be completed prior to the strengthening. The glass specimen shall also undergo impact testing for safety glazing.

Standard Specification for Bent Glass

GSO EN 1096-3:2021 建筑玻璃 镀膜玻璃 第3部分：C 类和 D 类镀膜的要求和测试方法

This European Standard specifies requirements and a test method related to resistance to solar radiation for coated glass for use in buildings. This test is aimed at evaluating if the exposure to solar radiation over an extended period of time produces any appreciable change in light transmittance and solar transmittance of the coated glass as well as a reduction of the infrared reflectance in the case of low emissivity coatings. This European Standard applies to Class C and D coatings as defined in EN 1096-1 and used in insulating glass units.

Glass in building - Coated glass - Part 3: Requirements and test methods for class C and D coatings

GSO ISO 1288-3:2021 建筑玻璃 玻璃抗弯强度的测定 第3部分：两点支撑试样试验（四点弯曲）

ISO 1288-3:2016 specifies a method for determining the bending strength, including the effects of the edges, of flat glass for use in building. The method specified can also be used to determine the bending strength of the edges of glass separately. The limitations of this part of ISO 1288 are described in ISO 1288‑1.

Glass in building — Determination of the bending strength of glass — Part 3: Test with specimen supported at two points (four point bending)

GSO EN 1096-2:2021 建筑玻璃 镀膜玻璃 第2部分：A、B 和 S 级镀膜的要求和测试方法

This European Standard specifies requirements and test methods related to artificial weathering and abrasion of coatings on glass for use in buildings. These tests are aimed at evaluating the resistance of the coating to attack by simulated natural weathering conditions as well as to abrasion. This attack can be considered as representative of that which could be found on the external and/or internal face of the glazing. This European Standard applies to Class A, B and S coatings, as described in EN 1096-1.

Glass in building - Coated glass - Part 2: Requirements and test methods for class A, B and S coatings

GSO EN 1096-4:2021 建筑玻璃镀膜玻璃 第4部分：产品标准

This European Standard covers the evaluation of conformity and the factory production control of coated glass for use in buildings. NOTE For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply.

Glass in building - Coated glass - Part 4: Product standard

GSO EN 1279-3:2021 建筑玻璃 中空玻璃 第3部分：气体泄漏率和气体浓度容限的长期测试方法和要求

This European Standard describes the test method for the determination of gas leakage rate and specifies the requirements for limit values for gas leakage rate and gas concentration for gas filled insulating glass units made a) in accordance with EN 1279 1:2018 and manufactured to EN 1279 6:2018, or b) for the purpose to demonstrate that components (e.g. edge seals or spacers) will allow the insulating glass unit to conform to the requirements given in EN 1279 1:2018, Clause 6.

Glass in building - Insulating glass units - Part 3: Long term test method and requirements for gas leakage rate and for gas concentration tolerances

GSO EN 12150-1:2021 建筑玻璃 热钢化钠钙硅酸盐安全玻璃 第1部分：定义和描述

This European Standard specifies tolerances, flatness, edgework, fragmentation and physical and mechanical characteristics of monolithic flat thermally toughened soda lime silicate safety glass for use in buildings. Information on curved thermally toughened soda lime silicate safety glass is given in Annex A, but this product does not form part of this European Standard. Other requirements, not specified in this European Standard, can apply to thermally toughened soda lime silicate safety glass which is incorporated into assemblies, e.g. laminated glass or insulating glass units, or undergo an additional treatment, e.g. coating. The additional requirements are specified in the appropriate glass product standard. Thermally toughened soda lime silicate safety glass, in this case, does not lose its bending strength characteristics and its resistance to temperature differentials. Surface finished glasses (e.g. sandblasted, acid etched) after toughening are not covered by this European Standard.

Glass in building - Thermally toughened soda lime silicate safety glass - Part 1: Definition and description

GSO EN 1279-6:2021 建筑玻璃 中空玻璃 第6部分：工厂生产控制和定期测试

This document describes the routine factory production control, the periodic testing and inspection and test methods to verify that an insulating glass unit (IGU) conforms to the system description.

Glass in building - Insulating glass units - Part 6: Factory production control and periodic tests