83.140.01 橡胶和塑料制品综合 标准查询与下载

T/CRIA 19002-2023 一次性使用医疗防护橡胶检查手套

本文件规定了灭菌或非灭菌一次性使用医疗防护橡胶检查手套（以下简称手套）的分类、材料、抽样和试片选择、技术要求、试验方法、检验规则、包装、标志。 本文件适用于医疗防护人员检查、诊断或治疗病患时为防止交叉感染而使用的检查手套。 手套的安全、正确使用方法和灭菌处理程序以及随后的包装和贮存程序，不在本文件的范围之内。

Disposable medical protective rubber examination gloves

T/HEBQIA 180-2023 汽车驾驶室热塑性弹性体底板垫

本文件规定了汽车驾驶室热塑性弹性体底板垫的产品分类、技术要求、试验方法、检验规则和标志、包装、运输和贮存。

Automobile cab thermoplastic elastomer floor mat

ASTM D6117-23 塑料木材和型材机械紧固件的标准试验方法

1.1 These test methods cover the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures. 1.2 The test methods appear in the following order: Sections Test Method A—Nail, Staple, or Screw Withdrawal Test 4 to 13 Test Method B—Nail, Staple, or Screw Lateral Resistance Test 14 to 22 1.3 Plastic lumber and plastic shapes are currently made predominately from recycled plastics. However, these test methods would also be applicable to similar manufactured plastic products made from virgin resins where the product is non-homogeneous in the cross-section. 1.4 The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Mechanical Fasteners in Plastic Lumber and Shapes

T/ZZB 3108-2023 电梯曳引机用摩擦片

本文件规定了电梯曳引机用摩擦片的分类和结构型式、基本要求、技术要求、试验方法、检验规则、标识、包装、运输和贮存以及质量承诺等要求。 本文件适用于额定速度不大于8 m/s的电梯曳引机用摩擦片（以下简称摩擦片）。

Friction linings for elevator traction machine

T/HBFPIA 012-2023 食品用工具一次性塑料挂式手套

本标准规定了食品用工具一次性塑料挂式手套（以下简称“手套”）的原辅料要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于以食品级塑料为原材料，经吹塑、热封等工艺生产，通过开孔固定于搭配使用的挂件上、带有点断线和高低口的食品用工具一次性塑料挂式手套。

Plastic hanging disposable tool gloves for food

T/GXSLHYXH 001-2023 《露天陆地自然环境降解聚烯烃餐饮具》

1  范围 本文件规定了露天陆地自然环境降解聚烯烃餐饮具的术语和定义、技术要求、试验方法、检验规则、标志、标识、包装、运输和贮存。 本文件适用于使用后暴露在自然环境下能实现生物降解，以聚烯烃树脂转化材料为原料加工制成的餐饮具(产品厚度0.20-0.80mm之间)。 2  规范性引用文件 3  术语和定义 4  分类 5  技术要求 6  试验方法 7  检验规则 8  标志、标识、包装、运输、贮存

Open-air land natural environment degradable polyolefin tableware

QB/T 5815-2023 生物降解塑料保温盒

Biodegradable plastic insulation box

QB/T 5818-2023 电子产品包装用生物降解塑料内衬

Biodegradable plastic lining for electronic product packaging

ASTM D7211-23 一般用途聚氯三氟乙烯（PCTFE）加工零件的标准规范

1.1  This specification is intended to be a means of calling out finished machined parts ready for general use. 1.2  This specification establishes requirements for parts machined from polychlorotrifluoroethylene (PCTFE) semifinished parts. 1.3  For aerospace grade, machined PCTFE parts, use Specification D7194 . Note 1:  Quick-quenched PCTFE will potentially exhibit dimensional relaxation in the vicinity of T g  = 55°C (131°F). Note 2:  Although no recommendations are made regarding the limiting upper use temperature of PCTFE, the heat deflection temperature of PCTFE as determined by Test Method D648 is 126°C (259°F). 1.4  The values stated in SI units are to be regarded as standard. The values in parentheses are for information only. 1.5  The following precautionary caveat pertains only to the test methods portion, Section 11 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 3:  There is no known ISO equivalent to this standard. 1.6  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Parts Machined from Polychlorotrifluoroethylene (PCTFE) and Intended for General Use

T/CPF 0054-2023 塑料包装制品易回收易再生设计要求及评价方法

本文件规定了“塑料包装制品易回收易再生设计”（简称“双易设计”）的分类、设计要求、评价方法、评价结果和报告。

Design requirements and evaluation method of easy collection and easy recycling for plastic packaging products

T/QGCML 707-2023 橡胶制宠物用品

本文件规定了橡胶制宠物用品的术语和定义、原料要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以天然橡胶为原料制成的供宠物喂食、洁牙、玩耍的橡胶制宠物用品。

Rubber pet products

T/SHDSGY 025-2023 新能源电池用导热结构胶技术规范

本文件规定了新能源电池用导热结构胶技术规范的术语和定义、原料要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于新能源动力电池电芯之间的粘结，电芯与模组边框的粘结，电池组加热板/水冷板/底板粘结用导热结构胶。

Technical specification for thermal conductivity structural adhesives for new energy batteries

ASTM D6779-23 聚酰胺模塑和挤压材料（PA）的标准分类系统和规范基础

1.1 This classification system covers polyamide materials suitable for molding and extrusion. Some of these compositions are also suitable for application from solution. 1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5. 1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This classification system is similar to ISO 16396-1 ⁄-2, although the technical content is significantly different. NOTE 2—The materials covered by this classification system include a subset of polyamides defined as polyphthalamides (PPA) as in 3.2.1, some of which are also classified in ASTM D5336. Specifically, groups 7, 10, 12, 13, 14, 15 and 17 in this standard are PPA materials. ASTM D5336 gives further details relating to groups 10, 12 and 13. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)

ASTM D7568-23 室外用聚乙烯基结构级塑料木材标准规范

1.1 This specification covers a type of plastic lumber product, defined as polyethylene-based structural-grade plastic lumber (SGPL), for use as main framing members, including joists, stringers, beams, columns; and secondary framing members, including planking, posts and bracing; in outdoor structures such as decks, boardwalks, docks, and platforms. 1.2 This specification is applicable to solid, rectangular SGPL products where polyethylene resin (non cross-linked) is the continuous phase and is at least 50 % of the product (by weight). 1.3 This specification is not applicable to plastic lumber products containing cellulosic materials as additives, fillers or fiber reinforcements. 1.4 SGPL products covered by this specification shall not be used as tensile members. 1.5 SGPL products are produced using several different manufacturing processes. These processes utilize a number of polyethylene resin material systems that include varying proportions of fillers, fiber reinforcements, and other chemical additives. 1.6 Due to thermodynamic effects that result in outersurface densification during manufacture, SGPL products are typically non-homogeneous in the cross-section. This standard does not address materials that have been modified from their original cross-section. 1.6.1 The cross-section non-homogeneity is addressed in the material property assessments in this document only for applications in which the product cross-section is not modified by cutting, notching, or drilling. For products modified in this manner, additional engineering considerations are required and they are beyond the scope of this document. 1.7 For purposes of this standard, an SGPL product is a specific combination of polyethylene resin, together with fillers, reinforcements, and additives. Each formulation is to be identified as a distinct and different product, to be tested and evaluated separately. 1.8 Diverse and multiple combinations of both virgin and recycled polyethylene material systems are permitted in the manufacture of SGPL products. 1.9 Fiber reinforcements used in SGPL include manufactured materials such as fiberglass (chopped or continuous), carbon, aramid and other polymeric materials. 1.10 A wide variety of chemical additives are typically added to SGPL formulations. Examples include colorants, chemical foaming agents, ultraviolet stabilizers, fire retardants, lubricants, anti-static products, heat stabilizers, and coupling agents. 1.11 Diverse types and combinations of filler systems are permitted in the manufacturing of SGPL products. Fillers that cause the product to fail the requirements of 6.13 are not permitted in the manufacturing of SGPL products. 1.12 In order for a product to be classified as SGPL, it must meet the minimum stress and modulus criteria consistent with the specific product as marked, and additionally the properties specified in Section 6 of this specification. 1.13 This specification pertains to SGPL where any reinforcement is uniformly distributed within the product. When reinforcement is not uniformly distributed, the engineering issues become substantially more complex. For this reason, such products are not covered in this document. 1.14 Products that fail at strains of less than 0.02 (2 %) when tested in flexure in accordance with 6.6 are not compatible with the underlying assumptions of Annex A1 and are beyond the scope of this standard (see Note 1). NOTE 1—Calculation of time-dependent properties in Annex A1 is based on the assumption that the product does not fail in a brittle manner. The 2 % strain limit was selected based on the judgment of the task group members that created Annex A1. 1.15 This specification addresses issues relevant to a buyer’s requirements for SGPL products and has therefore been developed in the format of a procurement specification. 1.16 Criteria for design are included as part of this specification for SGPL products. 1 This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.20 on Plastic Lumber. Current edition approved Feb. 1, 2023. Published February 2023. Originally approved in 2012. Last previous edition approved in 2017 as D7568 – 17. DOI:10.1520/D7568-23. *A Summary of Changes section appears at the end of this standard Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.17 Use of SGPL members in application will typically require the design of structural connections. Connection design between SGPL members falls outside the scope of this standard. 1.18 The values are stated in inch-pound units, as these are currently the most common units used by the US construction industry. Equivalent SI units are indicated in parentheses. 1.19 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 2—There is no known ISO equivalent to this standard. 1.20 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications

T/CNFIA 167-2023 食品接触用生物降解保鲜袋

1 范围 2 规范性引用文件 3 术语和定义 4 基本要求 5 技术要求 6 试验方法 7 检验规则 8 包装、贮存和运输

Biodegradable storage bags for food contact

T/ZZB 3026-2022 淀粉基塑料购物袋

本文件规定了淀粉基塑料购物袋的术语和定义、分类和标识、基本要求、技术要求、试验方法、检验规则、包装、标志、运输、贮存和质量承诺。 本文件适用于以淀粉和塑料树脂为主要原料生产的薄膜、经热合或黏合等制袋工艺加工制得的塑料购物袋，也适用于淀粉基塑料与其他材料复合的购物袋。 本文件不适用于仅以包装使用且不以携提为目的的淀粉基塑料袋如淀粉基塑料连卷袋（也称撕裂袋或点断袋）等。

Starch-based plastic shopping bags

T/GDKJ 0020-2022 食品包装用塑料容器盖

本文件规定了食品包装用塑料容器盖的要求、试验方法、检验规则、标志、标签、包装、运输和贮存。 本文件适用于以聚乙烯（PE）、聚丙烯（PP）树脂为原料，经注塑、热压或其他工艺成型的塑料盖，与普通食品包装用塑料容器（瓶、桶、罐）配套使用（以下简称：塑料盖），不具防盗性能。

Plastic container lids for food packaging

T/GDKJ 0017-2022 食品包装用聚乙烯塑料容器

本文件规定了食品包装用聚乙烯塑料容器的原料要求、要求、试验方法、检验规则、标志、标签、包装、运输、和贮存。 本文件适用于以聚乙烯树脂为主要原料生产的用于盛装食品的塑料容器（瓶、桶、罐），以下简称容器。

Polyethylene Plastic Containers for Food Packaging

T/GDKJ 0019-2022 食品接触用塑料容器

本文件规定了食品接触用塑料容器的原料要求、要求、试验方法、检验规则及标志、包装、运输、贮存。 本文件适用于罐体以聚对苯二甲酸乙二醇酯（PET）和聚乙烯（PE）为主要原料，采用注塑、拉伸、吹塑工艺成型，手把以聚丙烯（PP）为主要原料采用注塑工艺成型生产的，用于盛装酱油和调味粉的食品接触用特定塑料容器，以下简称容器。

Food Contact Plastic Containers

T/GDKJ 0018-2022 多层复合食品包装膜

      本文件规定了食品包装用多层复合膜的符号和缩略语、产品分类、原材料、要求、试验方法、检验规则、标志、包装、运输和贮存。       本文件适用于以聚乙烯膜（PE）、聚丙烯膜（BOPP 或 CPP）、聚酯膜（PET）、铝箔(Al)、尼龙膜（NY）、聚丙烯镀铝膜（MCPP 或 MBOPP）、聚酯镀铝膜（MPET）、双向拉伸聚酰胺（尼龙）膜（BOPA）等薄膜为基材，经复合而成并用于食品包装用的复合膜。

Multi-layer composite food packaging film